Safety Data Sheet Dichtungsmasse - Opel/Vauxhall Aftersales + IFZ

Adam Opel AG
Safety Data Sheet
according to Regulation (EC) No 1907/2006
Sealing compound
Print date: 05.10.2016
Page 1 of 11
Part-no. 93165267
SECTION 1: Identification of the substance/mixture and of the company/undertaking
Product group:
Others
Catalogue-no.: 15 03 305
Dichtungsmasse
Sealing compound
Matériau d‘étanchéité
1.2. Relevant identified uses of the substance or mixture and uses advised against
Use of the substance/mixture
Used in the automobile industry.
For processing instructions, please see annex safety data sheet.
1.3. Details of the supplier of the safety data sheet
Company name:
Adam Opel AG
Place:
D 65423 Rüsselsheim
Telefax: +49-6142/ 749-503
e-mail:
Responsible Department:
[email protected]
IFZ Ingenieurbüro und Consulting GmbH
Telefon: +49 30 2904897-10
Telefax: +49 - 30 / 2904897-20
Internationale Hotline: +49 6131 19240
United Kingdom +44 870 600 626 / 0870 600 6266
1.4. Emergency telephone
number:
Further Information
No more data.
SECTION 2: Hazards identification
2.1. Classification of the substance or mixture
Regulation (EC) No. 1272/2008
Hazard categories:
Serious eye damage/eye irritation: Eye Irrit. 2
Hazard Statements:
Causes serious eye irritation.
2.2. Label elements
Regulation (EC) No. 1272/2008
Signal word:
Warning
Pictograms:
Hazard statements
H319
Causes serious eye irritation.
Precautionary statements
P262
Do not get in eyes, on skin, or on clothing.
P264
Wash hands / face thoroughly after handling.
P280
Wear protective gloves/protective clothing/eye protection/face protection.
Revision No: 1,25
GB - EN
Revision date: 04.10.2016
Adam Opel AG
Safety Data Sheet
according to Regulation (EC) No 1907/2006
Sealing compound
Print date: 05.10.2016
P305+P351+P338
P337+P313
Page 2 of 11
Part-no. 93165267
IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if
present and easy to do. Continue rinsing.
If eye irritation persists: Get medical advice/attention.
Special labelling of certain mixtures
EUH208
Contains 3-Aminopropyltriethoxysilane. May produce an allergic reaction.
51 % of the mixture consists of ingredient(s) of unknown acute toxicity.
The product hardens in the presence of moisture and gives off methanol . Provide
adequate ventilation and/or an exhaust system. See safety data sheet for further
information.
Additional advice on labelling
The product is classified and labelled in accordance with the EC directives or respective national laws.
2.3. Other hazards
Contains epoxy constituents. See information supplied by the manufacturer.
On contact with water or humidity formation of: methanol (Highly flammable. Toxic by inhalation, in contact with
skin and if swallowed.).
SECTION 3: Composition/information on ingredients
3.2. Mixtures
Chemical characterization
Contains calcium carbonate.
The product hardens in the presence of moisture and gives off methanol .
Hazardous components
CAS No
Chemical name
EC No
Quantity
Index No
REACH No
Classification according to Regulation (EC) No. 1272/2008 [CLP]
2768-02-7
Trimethoxyvinylsilane
1 -< 3 %
220-449-8
01-2119513215-52
Flam. Liq. 3, Acute Tox. 4, STOT RE 2; H226 H332 H373
2530-83-8
[3-(2,3-Epoxypropoxy)propyl]- trimethoxysilane
<2%
219-784-2
Eye Dam. 1; H318
67-56-1
Methanol
200-659-6
< 1.0 %
603-001-00-X
Flam. Liq. 2, Acute Tox. 3, Acute Tox. 3, Acute Tox. 3, STOT SE 1; H225 H331 H311 H301 H370
**
919-30-2
3-Aminopropyltriethoxysilane
<1%
213-048-4
Acute Tox. 4, Skin Corr. 1B, Skin Sens. 1; H302 H314 H317
Full text of H and EUH statements: see section 16.
SECTION 4: First aid measures
4.1. Description of first aid measures
General information
In case of feeling unwell: Obtain medical attention. Show this safety data sheet to the doctor in attendance.
If unconscious, place the person in the recovery position and seek medical advice immediately. Do not
administer liquids to the unconscious person and avoid vomiting.
Revision No: 1,25
GB - EN
Revision date: 04.10.2016
Adam Opel AG
Safety Data Sheet
according to Regulation (EC) No 1907/2006
Sealing compound
Print date: 05.10.2016
Page 3 of 11
Part-no. 93165267
Protection is needed for the First Aider. (protective gloves, chemical-resistant; safety glasses)
When vapors or aerosols: Use breathing apparatus.
Eye wash fountains and safety showers must be easily accessible.
After inhalation
Remove the victim into fresh air. In case of irregular breathing or respiratory arrest: Oxygen or artificial
respiration, if needed. Lay the affected person down, and keep her or him warm and calm. If symptoms persist,
call a physician.
After contact with skin
Wash off with soap and plenty of water immediately. Remove all contaminated clothes and shoes. In the case
of skin irritation or allergic reactions see a physician.
After contact with eyes
Rinse with plenty of water immediately, also under the eyelids, for at least 15 minutes. Protect unharmed eye.
Remove contact lenses after the first 1 - 2 minutes and continue flushing. Consult an ophthalmologist
immediately.
Eye wash.
After ingestion
Clean mouth with water and drink plenty of water afterwards. Drink 1 or 2 glasses of water. Never give anything
by mouth to an unconscious person. Call a physician immediately.
4.2. Most important symptoms and effects, both acute and delayed
Severe eye irritation, irritation of the respiratory tract. May cause skin irritation. May produce an allergic
reaction.
Methanol:
May cause: Conjunctivitis, dizziness, insomnia, gastrointestinal disturbance, visual disturbances.
4.3. Indication of any immediate medical attention and special treatment needed
Symptomatic treatment (decontamination and vital functions). If necessary, contact poisson centre.
SECTION 5: Firefighting measures
5.1. Extinguishing media
Suitable extinguishing media
Carbon dioxide (CO2), dry powder, sprayed water stream.
Use a sprayed water stream to fight a large fire. (or alcohol-resistant foam)
Unsuitable extinguishing media
High volume water jet.
5.2. Special hazards arising from the substance or mixture
The product is combustible. Burning produces obnoxious and toxic fumes. In the event of a fire, the following
substances may be formed: silicon dioxide, carbon monoxide (CO) and carbon dioxide (CO2), traces of
incompletely burned hydrocarbons, nitrogen oxides (NOx), formaldehyde. The inhalation of hazardous
decomposition products may cause serious health damage.
5.3. Advice for firefighters
In the event of fire, wear self-contained breathing apparatus. Full protective flameproof clothing.
Clothing for firefighters which comply with the European norm EN 469 (including helmet, protective boots,
protective gloves) provide a basic protection for accident with chemicals.
Avoid contact with this material during fire fighting operations . If contact is likely, change to full chemical
resistant fire fighting clothing with self-contained breathing apparatus.
Additional information
The combustion gases are partially condensed with the water used to extinguish the fire and end up as a
contaminant in this water. Contaminated extinguishing water and soil must be disposed of in accordance with
official regulations.
SECTION 6: Accidental release measures
Revision No: 1,25
GB - EN
Revision date: 04.10.2016
Adam Opel AG
Safety Data Sheet
according to Regulation (EC) No 1907/2006
Sealing compound
Print date: 05.10.2016
Page 4 of 11
Part-no. 93165267
6.1. Personal precautions, protective equipment and emergency procedures
Provide adequate ventilation and/or exaust ventilation. Remove all sources of ignition. Wear personal
protective equipment. Avoid contact with skin and eyes. Do not breathe in vapours. Keep unprotected people
away. Slipping hazard due to leakage.
6.2. Environmental precautions
Do not flush into surface water or sanitary sewer system.
6.3. Methods and material for containment and cleaning up
Prevent further leakage or spillage if safe to do so. Take up mechanically and collect in suitable container for
disposal. Dispose of the material collected according to regulations.
6.4. Reference to other sections
See also section 8, 13.
SECTION 7: Handling and storage
7.1. Precautions for safe handling
Advice on safe handling
After use: Containers keep tightly closed. Provide sufficient air exchange and/or exhaust in work rooms. Do not
inhale large amounts of the vapours released at the beginning of the curing process (contact with humid air).
Avoid contact with skin, eyes and clothing. Avoid spillage and leakage due to the risk of slipping . Wear suitable
protective clothing. See section 8. Wash hands and face before breaks and immediately after handling the
product. Wash contaminated skin areas thoroughly with soap and water .
Advice on protection against fire and explosion
Keep product and empty container away from heat and sources of ignition. Do not smoke. Take precautionary
measures against static discharges. Use a spark-free tool. Do not burn, or use a cutting torch on the empty
drum.
Further information on handling
Contains epoxy constituents. See information supplied by the manufacturer.
7.2. Conditions for safe storage, including any incompatibilities
Requirements for storage rooms and vessels
Store in original container. Pay attention to storage conditions on the label. Keep containers tightly closed in a
cool, well-ventilated place. Keep in a dry place. Keep away from open flames, hot surfaces, and sources of
ignition. The product may only come into contact with suitable materials. Store product upright. Do not drop.
Avoid shock and friction. Always keep in containers made from the same material as the original one. Do not
re-use empty containers.
Advice on storage compatibility
Protect from humid air and water. The product hardens in the presence of moisture and gives off methanol.
Further information on storage conditions
Protect from heat and direct sunlight. Smoking in the storage rooms is forbidden.
Total storage period: 12 months / Storage temperatures (°C): +25
7.3. Specific end use(s)
No data available.
SECTION 8: Exposure controls/personal protection
8.1. Control parameters
Revision No: 1,25
GB - EN
Revision date: 04.10.2016
Adam Opel AG
Safety Data Sheet
according to Regulation (EC) No 1907/2006
Sealing compound
Print date: 05.10.2016
Page 5 of 11
Part-no. 93165267
Exposure limits (EH40)
CAS No
Substance
1317-65-3
Calcium carbonate, respirable
67-56-1
Methanol
ppm
mg/m³
-
fibres/ml
Category
Origin
4
TWA (8 h)
WEL
-
-
STEL (15 min)
WEL
200
266
TWA (8 h)
WEL
250
333
STEL (15 min)
WEL
Additional advice on limit values
The product hardens in the presence of moisture and gives off methanol.
8.2. Exposure controls
Appropriate engineering controls
Use product only in closed system. Provide adequate ventilation and/or exaust ventilation. Follow the maximum
workplace concentration values. If necessary: Local exhaust.
Personal protection equipment should comply with the relevant standards, be suitable for purpose, in good
condition and maintained as specified.
Eye wash
Protective and hygiene measures
When using, do not eat, drink, or smoke. Keep away from food, drink, and animal food stuffs. Avoid contact
with skin and eyes. Do not breathe in vapours. Wash hands, forearms and face thoroughly after handling
chemical products, before eating, smoking and using the lavatory and at the end of the working period.
Remove and wash contaminated clothing before re-use. Contaminated work clothing should not be allowed out
of the workplace. Eye wash fountains and safety showers must be easily accessible.
Eye/face protection
Tightly fitting safety goggles (EN 166) / facial protection.
Hand protection
Protective gloves, chemical-resistant (EN 374). The manufacturer recommends the following glove materials:
butyl rubber. Penetration time of the glove material: > 480 min. Safety gloves should be selected for the actual
conditions of use and in accordance with the instructions for use provided by the manufacturer.
Please note that the daily use of a chemical glove in practice may be considerably shorter than the permeation
time calculated in EN 374 as a result of many different factors (for example temperature). Use tested protective
gloves. Protective gloves should be replaced immediately if damaged or in case of signs of wear.
Skin protection
Wear suitable protective clothing.
No rings, watches or similar things should be worn. Product residues can remain and, therefore, can trigger
skin reactions. If necessary: Clean thoroughly. Discard items which cannot be decontaminated, including
leather articles such as shoes, belts and watchbands.
Respiratory protection
Only use in well-ventilated areas. Use respiratory equipment when gases, vapours/aerosols form.
When the concentration in the air is over the maximum occupational exposure limit, an approved respiratory
protection apparatus must be worn.
Methanol:
Respirator with AX filter - EN 14387 (organic vapours - Boiling point/range < 65°C).
In the case of dust or aerosol formation use respirator with filter model A -P2 (according to EN 14387).
Environmental exposure controls
No data available.
Revision No: 1,25
GB - EN
Revision date: 04.10.2016
Adam Opel AG
Safety Data Sheet
according to Regulation (EC) No 1907/2006
Sealing compound
Print date: 05.10.2016
Page 6 of 11
Part-no. 93165267
SECTION 9: Physical and chemical properties
9.1. Information on basic physical and chemical properties
Physical state:
Colour:
Odour:
paste
grey
alcoholic
Test method
pH-Value:
n.a.
Changes in the physical state
Melting point:
n.a.
Initial boiling point and boiling range:
n.a.
Flash point:
Sustaining combustion:
63 °C
No data available
Flammability
Solid:
No data available.
No data available.
Gas:
Explosive properties
No data available.
Lower explosion limits:
Upper explosion limits:
No data available.
No data available.
Ignition temperature:
> 200 °C
see below
Auto-ignition temperature
Solid:
Gas:
n.a.
n.a.
Decomposition temperature:
No data available. (See section 10.)
Oxidizing properties
No data available.
Vapour pressure:
No data available.
Density (at 25 °C):
1.24 g/cm³ (water = 1)
Water solubility:
insoluble
Solubility in other solvents
No data available.
Partition coefficient:
No data available.
Viscosity / dynamic:
(at 25 °C)
300000 mPa·s
Vapour density:
No data available. (air = 1)
Evaporation rate:
No data available.
9.2. Other information
Solid content:
No data available.
The product is not self-igniting.
Odour threshold value: No data available.
SECTION 10: Stability and reactivity
Revision No: 1,25
GB - EN
Revision date: 04.10.2016
Adam Opel AG
Safety Data Sheet
according to Regulation (EC) No 1907/2006
Sealing compound
Print date: 05.10.2016
Page 7 of 11
Part-no. 93165267
10.1. Reactivity
On contact with water or humidity formation of: methanol.
10.2. Chemical stability
Stable under proper storage and handling.
10.3. Possibility of hazardous reactions
No dangerous reactions occur under normal storage conditions and in normal use.
10.4. Conditions to avoid
Protect from humid air and water. The product hardens in the presence of moisture and gives off methanol.
10.5. Incompatible materials
acids, alkalies, water, strong oxidizers
10.6. Hazardous decomposition products
Possible decomposition products in case of hydrolysis are: methanol.
Decomposes on heating. (at high temperatures)
Thermal decomposition can lead to release of irritating gases and vapours.
Small amounts of formaldehyde are formed in the presence of air at temperatures above approx. 150°C due to
oxidative decomposition. See also section 5.
Further information
No decomposition if stored and applied as directed.
SECTION 11: Toxicological information
11.1. Information on toxicological effects
Toxicocinetics, metabolism and distribution
No data available.
Acute toxicity
No data is available on the product itself. The following toxicological assessments are based on the
toxicological knowledge of the separate components of the product.
Methanol:
LC50/inhalative/rat: 64000 ppm/4h
CAS No
Chemical name
Exposure route
2768-02-7
67-56-1
919-30-2
Dose
Species
Source
Trimethoxyvinylsilane
inhalative vapour
LC50
2773 mg/l
inhalative aerosol
ATE
1.5 mg/l
oral
LD50
5628 mg/kg
rats
dermal
LD50
15800 mg/kg
rabbit
inhalative (4 h) vapour
LC50
85.26 mg/l
rats
inhalative aerosol
ATE
0.5 mg/l
ATE
500 mg/kg
Methanol
3-Aminopropyltriethoxysilane
oral
Irritation and corrosivity
Revision No: 1,25
GB - EN
Revision date: 04.10.2016
Adam Opel AG
Safety Data Sheet
according to Regulation (EC) No 1907/2006
Sealing compound
Print date: 05.10.2016
Page 8 of 11
Part-no. 93165267
Causes serious eye irritation.
Trimethoxyvinylsilane: The volatile by-products released during the processing may irritate the eyes and
respiratory tract.
Prolonged or repeated skin contact can have an irritating effect .
Sensitising effects
May produce an allergic reaction. (3-Aminopropyltriethoxysilane)
Contains compounds which contain epoxide. May produce an allergic reaction.
Carcinogenic/mutagenic/toxic effects for reproduction
No data available.
STOT-single exposure
No data available.
STOT-repeated exposure
Ingestion: More severe effects (bladder) if excessive exposure.
Aspiration hazard
No data available.
Additional information on tests
On contact with water or humidity formation of: methanol. Toxic by inhalation, in contact with skin and if
swallowed. Toxic: danger of very serious irreversible effects through inhalation , in contact with skin and if
swallowed.
Small amounts of formaldehyde are formed in the presence of air at temperatures above approx. 150°C due to
oxidative decomposition. In the case of inhalation formaledyde vapours are harmful to health with
concentrations of less than 1ppm. They can irritate the eyes and the respiratory system.
Formaldehyde: Toxic by inhalation, in contact with skin and if swallowed. Causes severe caustic burns to skin
and eyes. Risk of serious damage to eyes. May produce an allergic reaction. May cause genetic defects. May
cause cancer. The following symptoms can occur after inhalation: cough, lung edema. Symptoms may be
delayed.
SECTION 12: Ecological information
12.1. Toxicity
No data is available on the product itself.
CAS No
Chemical name
2768-02-7
Trimethoxyvinylsilane
Aquatic toxicity
67-56-1
[h] | [d] Species
Dose
Acute fish toxicity
LC50
191 mg/l
96 h Oncorhynchus mykiss
Acute algae toxicity
ErC50
> 100 mg/l
72 h -
Acute crustacea toxicity
EC50
> 100 mg/l
48 h Daphnia magna
Acute fish toxicity
LC50
15400 mg/l
96 h Lepomis macrochirus
Acute crustacea toxicity
EC50
> 10000 mg/l
48 h Daphnia magna
Source
Methanol
12.2. Persistence and degradability
No data available.
12.3. Bioaccumulative potential
Partition coefficient n-octanol/water
CAS No
Chemical name
67-56-1
Methanol
Revision No: 1,25
Log Pow
-0.77
GB - EN
Revision date: 04.10.2016
Adam Opel AG
Safety Data Sheet
according to Regulation (EC) No 1907/2006
Sealing compound
Print date: 05.10.2016
Page 9 of 11
Part-no. 93165267
12.4. Mobility in soil
No data available.
12.5. Results of PBT and vPvB assessment
No data available.
12.6. Other adverse effects
Contains no organically bonded halogens (AOX), nitrates, heavy metal compounds and formaldehyde.
Further information
Water-endangering to a small extent. Do not flush into surface water or sanitary sewer system. Do not allow
material to contaminate ground water system.
SECTION 13: Disposal considerations
13.1. Waste treatment methods
Advice on disposal
Disposal in accordance with the official regulations . Hazardous waste incineration. Must be incinerated in a
suitable incineration plant authorised under the Environmental Protection Act . Must not be disposed of with
domestic waste. Do not let product enter drains.
Waste disposal number of waste from residues/unused products
WASTES FROM ORGANIC CHEMICAL PROCESSES; wastes from the MFSU of plastics, synthetic
070216
rubber and man-made fibres; waste containing hazardous silicones
Classified as hazardous waste.
Waste disposal number of used product
WASTES FROM ORGANIC CHEMICAL PROCESSES; wastes from the MFSU of plastics, synthetic
070216
rubber and man-made fibres; waste containing hazardous silicones
Classified as hazardous waste.
Waste disposal number of contaminated packaging
WASTE PACKAGING; ABSORBENTS, WIPING CLOTHS, FILTER MATERIALS AND
150110
PROTECTIVE CLOTHING NOT OTHERWISE SPECIFIED; packaging (including separately
collected municipal packaging waste); packaging containing residues of or contaminated by
hazardous substances
Classified as hazardous waste.
Contaminated packaging
Disposal in accordance with the official regulations . Empty containers should be transported/delivered using a
registered waste carrier for local recycling or waste disposal. Dispose of non-cleansing packaging in the same
way as the product.
Suitable cleaning agents: alcohol.
SECTION 14: Transport information
Land transport (ADR/RID)
14.1. UN number:
not regulated
14.2. UN proper shipping name:
not regulated
14.3. Transport hazard class(es):
not regulated
14.4. Packing group:
not regulated
Other applicable information (land transport)
Not classified as dangerous regarding transport regulations.
Inland waterways transport (ADN)
14.1. UN number:
not regulated
14.2. UN proper shipping name:
not regulated
14.3. Transport hazard class(es):
not regulated
Revision No: 1,25
GB - EN
Revision date: 04.10.2016
Adam Opel AG
Safety Data Sheet
according to Regulation (EC) No 1907/2006
Sealing compound
Print date: 05.10.2016
14.4. Packing group:
Part-no. 93165267
Page 10 of 11
not regulated
Other applicable information (inland waterways transport)
Not classified as dangerous regarding transport regulations.
Marine transport (IMDG)
14.1. UN number:
not regulated
14.2. UN proper shipping name:
not regulated
14.3. Transport hazard class(es):
not regulated
14.4. Packing group:
n.d.a.
Other applicable information (marine transport)
Not classified as dangerous regarding transport regulations.
Air transport (ICAO-TI/IATA-DGR)
14.1. UN number:
not restricted
14.2. UN proper shipping name:
not restricted
14.3. Transport hazard class(es):
not restricted
14.4. Packing group:
n.d.a.
Other applicable information (air transport)
Not classified as dangerous regarding transport regulations.
14.5. Environmental hazards
ENVIRONMENTALLY HAZARDOUS:
no
14.6. Special precautions for user
Not classified as dangerous regarding transport regulations.
14.7. Transport in bulk according to Annex II of Marpol and the IBC Code
No data available.
SECTION 15: Regulatory information
15.1. Safety, health and environmental regulations/legislation specific for the substance or mixture
EU regulatory information
Additional information
No Substances of Very High Concern (SVHC) according REACH Articel 57.
National regulatory information
Employment restrictions:
Observe restrictions to employment for juvenils according to the 'juvenile
work protection guideline' (94/33/EC).
Additional information
The national regulations have to be complied with as necessary.
15.2. Chemical safety assessment
Chemical safety assessments for substances in this mixture were not carried out.
SECTION 16: Other information
Changes
Section: 2, 4, 7, 8, 11, 13
Abbreviations and acronyms
n.a. = not applicable
n.d. = not determined
n.d.a. = no data available
ATE = Acute Toxicity Estimate
VOC = Volatile organic compounds
Revision No: 1,25
GB - EN
Revision date: 04.10.2016
Adam Opel AG
Safety Data Sheet
according to Regulation (EC) No 1907/2006
Sealing compound
Print date: 05.10.2016
Page 11 of 11
Part-no. 93165267
SVHC = substance of very high concern
REACH = Registration, Evaluation, Authorisation and Restriction of Chemicals Regulation (EC) No 1907/2006
GHS = Globally Harmonized System
CLP = Classification Labelling Packaging Regulation; Regulation (EC) No 1272/2008
Relevant H and EUH statements (number and full text)
H225
Highly flammable liquid and vapour.
H226
Flammable liquid and vapour.
H301
Toxic if swallowed.
H302
Harmful if swallowed.
H311
Toxic in contact with skin.
H314
Causes severe skin burns and eye damage.
H317
May cause an allergic skin reaction.
H318
Causes serious eye damage.
H319
Causes serious eye irritation.
H331
Toxic if inhaled.
H332
Harmful if inhaled.
H370
Causes damage to organs.
H373
May cause damage to organs (bladder) through prolonged or repeated exposure if
swallowed.
EUH208
Contains 3-Aminopropyltriethoxysilane. May produce an allergic reaction.
Further Information
The information is based on present levels of our knowledge. It does not, however, give assurances of product
properties and establishes no contract legal rights.
The product is to be used exclusively for the applications named in the technical data sheet or in the
processing instructions.
The receiver of our product is singularly responsible for adhering to existing laws and regulations.
(The data for the hazardous ingredients were taken respectively from the last version of the sub-contractor's safety
data sheet.)
Revision No: 1,25
GB - EN
Revision date: 04.10.2016
Product information
Sealing compound
93165267 – 15 03 305
The product is an RTV (room temperature vulcanizing) silicone liquid gasket developed for flange
surfaces that have to withstand extreme vibrations, such as valve covers, oil sumps, water pumps
etc.
Excellent chemical resistance to engine coolant and engine oil.
Application
The product shows excellent adhesion even on slightly soiled surfaces. In order to achieve optimum
results, however, humidity, grease and other dirt should be removed from the mating surface.
According to the joint conditions (width, roughness depths, bumps, etc.), apply a suitable quantity of
the silicone evenly on the mating surface and join, position correctly and fix the parts within a period of
ten minutes.
Excess material can easily be removed with a piece of cloth.
The degree of hardening of the silicone varies depending on the layer thickness, the ambient
temperature and relative humidity. At +25°C and 55 % relative humidity, the surface starts drying after
15 minutes.
Immediate leak tightness for pressure and engine tests is achieved.
The application temperature range is in a range of -60°C to +200°C.
Special instructions
Storage
12 months at +25°C
Keep away from direct sun, moisture and heat and store in a well-ventilated place.
Safety
For handling our products please refer to the instructions on our safety data sheet at www.ifz-berlin.de
and the safety instructions on the product label.
The receiver of our product is singularly responsible for adhering to existing laws and regulations.
11/25/2013
Adam Opel AG, D-65423 Rüsselsheim, Germany
Page | 1
Please note: The data provided above are only intended for general information. Due to the processing, application and storage conditions outside our sphere of influence
and the large number of different materials, we provide no guarantee for specific application results.

Download Report