PIPE & FITTINGS
PRODUCT CATALOGUE
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
EURAPIPE ABS
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
disclaimer
COPYRIGHT
This document has been prepared
by Pentair Water Solutions to assist
qualified engineers and contractors in
the selection of the Company’s product,
and is not intended to be an exhaustive
statement on pipeline design,
installation or technical matters. Any
conclusions, formulae and the like
contained in the manual represent best
estimates only and may be based on
assumptions which, while reasonable
may not necessarily be correct for every
installation.
This manual is a publication of Pentair
Water Solutions, ABN 75 087 415 745,
and must not be copied or reproduced
in whole or part without the Company’s
prior written consent.
Successful installation depends
on numerous factors outside the
Company’s control, in to any person
who relies on the whole or any part of
this manual and excludes all liability
imposed by any statute or by the
general law in respect of this manual
whether statements and representation
in this manual are made negligently
or otherwise except to the extent it is
prevented by law from so doing. The
manual is not an offer to trade and
shall not form any part of the trading
terms in any transaction. Pentair Water
Solutions trading terms contain specific
provisions which limit the liability of
Pentair Water Solutions to the cost of
replacing or repairing any defective
product.
This manual is and shall remain as
the Company’s property and shall be
returned to the Company on its request.
The Company reserves the right to
make changes to any matter at any
time without notice.
All Pentair trademarks and logos are
owned by Pentair Ltd. All other brand
or product names are trademarks or
registered marks of their respective
owners.
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
3
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
THE COMPANY
INTRODUCTION
MATERIAL PROPERTIES
Pentair has a highly trained
and experienced team who
are dedicated to the design,
manufacture, installation and
operation of its products.
ABS thermoplastics are recognized
as a suitable material to be used in
many industry applications.
The formulation of ABS used by
Euratech has been developed
in conjunction with polymer
manufacturers to optimise
performance in respect to tensile
strength, chemical resistance,
ductility, resistance to weathering,
heat stability, low toxicity, taint
free and ease processing from raw
material to finished product.
The company is committed
to a program of continuous
improvement in the quality and
reliability of its products and
services. Technical advice is
available from our engineer team.
Application advice and support is
also available.
Our products are manufactured
to conform to recognised
international engineering quality
standard such as Australian
Standard AS/NZS 3518 : 2004.
Pantair’s is also accredited to
ISO9001:2008 Quality System.
PRODUCT APPLICATIONS
Our products are widely used in a variety of applications such as:
• HVAC, chilled water and condenser
ABS piping systems are replacing
many piping systems made from
other materials.
Pentair’s ABS piping systems
compromises a large range of
pressure ratings for pipes and
fittings, joined together by cold
solvent cement welding.
THE MATERIAL
Acrylonitrile – Butadiene – Styrene
(ABS) identifies a family of
engineering thermoplastics with
a board range of performance
characteristics. The copolymeric
system is alloyed to yield the
optimum balance of properties
suited to the selected end use.
• Water reticulation
ACRYLONITRILE
• Domestic plumbing
imparts chemical resistance and
rigidity.
• Water treatment plants
• Waste water treatment and recycling
plants
• Power generation plants
• Industrial plants such as electronics,
food processing, chemical, paper
mills, palm oils and rubber mills.
PRESSURE RATINGS
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
The material is very tough and
resilient, has high impact strength,
good chemical resistance non-toxic
and taint free.
EURAPIPE ABS piping systems are
available in the following range of
sizes: DN15 to DN750. Standard
o
pressure ratings at 20 C are 900
KPa, 1200 KPa and 1500 KPa
(Class C, Class D and Class E).
4
BUTADIENE
endows the product with impact
strength, toughness and abrasion
resistance.
STYRENE
contributes to the lustre, ease of
processing and rigidity.
ABS is tough and strong over the
recommended temperature range
of -30oC to +60oC.
THE OUTSTANDING
PROPERTIES OF ABS ARE:
• High impact strength and ductility,
which combine to give exceptional
toughness.
• Good chemical resistance.
• Abrasion resistance.
• High strength solvent weld jointing
which allows efficient system
assembly and modification.
• Withstands aggressive ground
waters.
• High strain tolerance for buried
applications.
• Good resistance to ultraviolet light.
• Better flow rate.
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
ENVIRONMENTAL
WEATHER RESISTANCE
SMOOTH BORE
The use of ABS contributes positively
to the environment as it takes
approximately one sixth of the energy
to manufacture compared to metal
products. This has direct savings
in greenhouse gas emissions.
Additionally ABS is lead and chlorine
free and can be readily recycled.
EURAPIPE ABS is one of the
most weather resistance polymers
available today. Successful field
tests have been completed on
piping systems having been exposed
to weathering for over 30 years.
EURAPIPE ABS does not suffer
from internal corrosion and
provides a smooth bore for the life
of the piping systems. The smooth
bore does not support formation
of scale and slime as do cement
based lined products.
IMPACT STRENGTH
The butadiene constituent in ABS
affords unrivalled resistance to
impact. This means that EURAPIPE
Piping systems may be used in
more critical applications where
other types of plastics could not be
considered.
ABS is a ductile material and the
mode of failure resembles that of
soft copper. Failure is by ductile
distortion and tearing, the localized
nature minimizing the loss of pipe
contents.
In contract, crack propagation and
hazardous material fragmentation
accompany the failure of brittle
material.
LIGHT WEIGHT
ABS is one-sixth the weight of steel
systems, making EURAPIPE easy
to handle and install. This reduces
the cost of installation, handling
and transport.
CHEMICAL RESISTANCE
EURAPIPE ABS is unaffected by
both internal and external attack
by a wide range of acids, alkalis,
ground water salts and other
environmental factors. Please refer
to Pentair for further information.
QUICK REFERENCE CHEMICAL REISITANCE
• Weak acids Good resistance
• Strong acids Limited resistance
25
• Weak alkalis Good resistance
• Strong alkalis Good resistance
IMPACT ENERG Y (Kgm)
20
15
uPVC @ 20° C
• Aggressive soils
Excellent resistance
AB S @ 0° C
• Metal salts Good resistance
• Sea water Excellent resistance
AB S @20° C
• Aromatic Poor resistance
hydrocarbons
10
• Organic solvents
Poor resistance
5
0
20
32
50
1002
PI PE S IZE (mm)
00
ABRASION RESISTANCE
EURAPIPE ABS offers outstanding
resistance to abrasion and erosion
from aggressive slurries which
can rapidly damage steel or other
traditional pipe materials.
The ABS formulation contains no
harmful metallic stabilizers and
it has been widely used for many
years in piping systems for drinking
water, medical preparations,
food products and potable water.
EURAPIPE ABS systems is ideal for
potable cold water. It conforms to
World Health Organisation, E.E.C.
and AS4020 / BS6920 requirement
for potable water reticulation and
distribution.
The EURAPIPE range also utilizes
the proven traditional method of
joining ABS pipes, cold solvent
cement welding, which provides a
homogenous bond/weld between
pipes and fittings (SWJ).
TEMPERATURE RANGE
A great advantage of EURAPIPE
ABS over other plastic systems is
its ability to perform over a wide
temperature range from -30°C
to +60°C. This makes EURAPIPE
ABS very versatile and capable of
handling a wide variety of fluids
from refrigerants to moderately hot
corrosive liquids.
THERMAL EXPANSION
All thermoplastics expand at a
greater rate than metal.
Expansion need not caused undue
concern in design or installation
of an ABS piping system provided
that due recognition is taken at
the design stage. The reduced
flexural modulus of ABS over that
of steel results in reduced loads
on supports and equipment arising
from thermal strains. The linear
coefficient of thermal expansion of
ABS is 10.1 x 10-5 m/m°C.
5
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
NON-TOXIC / TAINT FREE
COLD SOLVENT WELD
JOINING
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
DURAFLO ABS PRESSURE PIPE SERIES 1
CODE
PAGE 8-9
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
CODE 100
PAGE 10
STUB FLANGE
CODE 135
PAGE 11
FULL FACE FLANGE
CODE 129, 130, 317, 322
PAGE 12
SHOULDER STYLE COUPLING
CODE 953 PAGE 14
BLANK FLANGE STUB STYLE
CODE 136 PAGE 15
BLANK FULL FACE FLANGE
CODE 131, 326, 313, 325
PAGE 16
BACKING RING
CODE 415, 416, 425, 413
PAGE 19, 20, 21 & 22
VALVE SUPPORT PLATE
CODE 465, 460, 470 PAGE 23
GASKET (FULL FACE STYLE)
CODE 409, 410, 426 PAGE 24
GASKET
(STUB FLANGE STYLE)
CODE 431 PAGE 25
ELBOW 45O
FAUCET ELBOW 90O
MOULDED BEND 90O
BEND 90O R=1.2D (Sp-Sp)
CODE 119
PAGE 27
CODE 116
PAGE 28
CODE 118
PAGE 29
BLIND STEEL PLATE
CODE 731, 732
CODE 305
PAGE 17
PAGE 30
SHOULDER END
CODE 954
PAGE 13
BLIND ABS LINER
CODE 721, 722
PAGE 18
ELBOW 90O
CODE 115
PAGE 26
BEND 45º R=1.2D
CODE 304
PAGE 31
BEND 90º SHORT RADIUS
BEND 45º SHORT RADIUS
BEND 90º LONG RADIUS
BEND 45º LONG RADIUS
EQUAL TEE (So-SoxSo)
CODE 308
CODE 312
CODE 309
CODE 310
CODE 122
PAGE 32
REDUCING TEE SPIGOT
OFFTAKE (So-SoxSp)
CODE 120
PAGE 37
6
PLAIN SOCKET
PAGE 33
REDUCING TEE SOCKET
OFFTAKE (So-SoxSo)
CODE 122
PAGE 38
PAGE 34
TEE THREADED OFF TAKE
(So-SoxTh)
CODE 121
PAGE 39
PAGE 35
Y PIECE 45º
CODE 128
PAGE 40
PAGE 36
SADDLE STRIPS
CODE 146
PAGE 41
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
TAPPING SADDLES
CODE 127
PAGE 42
VALVE SOCKET
CODE 151
PAGE 47
SADDLE CLIP
CODE 455
PAGE 52
BALL CHECK VALVE SINGLE
UNION
CODE 836, 838 PAGE 57
REDUCING SOCKET
CODE 114
PAGE 43
FAUCET ADAPTOR
CODE 153
PAGE 48
PIPE CLIP
CODE 434
PAGE 53
BALL VALVE DOUBLE UNION
CODE 880, 882 PAGE 58
REDUCING BUSH
CODE 109
PAGE 44
CAP
CODE 140
CODE 101
PAGE 45
THREADED PLUG
PAGE 49
RUBBER EXPANSION JOINT
CODE 452
FAUCET SOCKET
PAGE 54
CODE 155
PAGE 50
ANCHOR SLEEVE
CODE 272
PAGE 55
ABS SOLVENT CEMENT
MEK CLEANER/PRIMER
CODE 461
CODE 463 PAGE 59
PAGE 59
VALVE ADAPTOR
CODE 107
PAGE 46
SOCKET UNION
CODE 205
PAGE 51
ANCHOR FLANGE
CODE 137
PAGE 56
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
7
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
DURAFLO ABS PRESSURE PIPE SERIES 1
SIZE/PRESSURE RATING
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
DN
15
S1
COMPOUND
CLASSIFICATION
PRODUCT
CODE
PRESSURE
(BAR)
OD MEAN
(mm)
WALL
MEAN
(mm)
ID MEAN
(mm)
DURAFLO
ABS160
R11.5200.015
20
21.4
2.1
17.2
DN
20
S1
PN18
DURAFLO
ABS160
R11.5180.020
18
26.8
2.4
21.9
DN
25
S1
PN18
DURAFLO
ABS160
R11.5180.025
18
33.6
3.0
27.5
DN
32
S1
PN18
DURAFLO
ABS160
R11.5180.032
18
42.3
3.2
35.9
DN
40
S1
PN18
DURAFLO
ABS160
R11.5180.040
18
48.3
3.6
41.0
DN
50
S1
PN12
DURAFLO
ABS160
R11.5120.050
12
60.4
3.7
53.0
DN
50
S1
PN15
DURAFLO
ABS160
R11.5150.050
15
60.4
4.5
51.3
DN
65
S1
PN12
DURAFLO
ABS160
R11.5120.065
12
75.4
4.5
66.4
DN
65
S1
PN15
DURAFLO
ABS160
R11.5150.065
15
75.4
5.7
64.0
DN
80
S1
PN 9
DURAFLO
ABS160
R11.5090.080
9
88.9
4.1
80.7
DN
80
S1
PN12
DURAFLO
ABS160
R11.5120.080
12
88.9
5.4
78.2
DN
80
S1
PN15
DURAFLO
ABS160
R11.5150.080
15
88.9
6.6
75.7
DN
100
S1
PN 9
DURAFLO
ABS160
R11.5090.100
9
114.3
5.3
103.8
DN
100
S1
PN12
DURAFLO
ABS160
R11.5120.100
12
114.3
6.8
100.7
DN
100
S1
PN15
DURAFLO
ABS160
R11.5150.100
15
114.3
8.5
97.4
*DN
125
S1
PN 9
DURAFLO
ABS160
R11.5090.125
9
140.2
6.4
127.3
*DN
125
S1
PN 12
DURAFLO
ABS160
R11.5120.125
12
140.2
8.4
123.4
DN
125
S1
PN 15
DURAFLO
ABS160
R11.5150.125
15
140.2
10.4
119.4
DN
150
S1
PN 9
DURAFLO
ABS160
R11.5090.150
9
168.3
7.7
152.9
DN
150
S1
PN12
DURAFLO
ABS160
R11.5120.150
12
168.3
10.1
148.1
DN
150
S1
PN15
DURAFLO
ABS160
R11.5150.150
15
168.3
12.4
143.4
*DN
200
S1
PN 6
DURAFLO
ABS160
R11.5060.225
6
225.3
7.1
211.3
DN
200
S1
PN 9
DURAFLO
ABS160
R11.5090.225
9
225.3
10.3
204.7
DN
200
S1
PN15
DURAFLO
ABS160
R11.5150.225
15
225.3
16.6
192.1
*DN
225
S1
PN 6
DURAFLO
ABS160
R11.5060.250
6
250.4
7.8
234.8
DN
225
S1
PN 9
DURAFLO
ABS160
R11.5090.250
9
250.4
11.4
227.5
DN
225
S1
PN15
DURAFLO
ABS160
R11.5150.250
15
250.4
18.5
213.0
* Denotes Non-Stockable
8
PN20
TYPE
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
DURAFLO ABS PRESSURE PIPE SERIES 1
SIZE/PRESSURE RATING
*DN
300
S1
PN 6
TYPE
DURAFLO
ABS160
PRODUCT
CODE
PRESSURE
(BAR)
OD MEAN
(mm)
WALL
MEAN
(mm)
ID MEAN
(mm)
R11.5060.315
6
315.5
9.7
296.0
DN
300
S1
PN 9
DURAFLO
ABS160
R11.5090.315
9
315.5
14.4
286.7
DN
300
S1
PN15
DURAFLO
ABS160
R11.5150.315
15
315.5
23.2
269.1
*DN
350
S1
PN 6
DURAFLO
ABS160
R11.5060.355
6
355.5
11.0
333.6
DN
350
S1
PN 9
DURAFLO
ABS160
R11.5090.355
9
355.5
16.2
323.2
DN
350
S1
PN15
DURAFLO
ABS160
R11.5150.355
15
355.5
26.2
303.1
*DN
375
S1
PN 6
DURAFLO
ABS160
R11.5060.400
6
400.5
12.3
375.8
DN
375
S1
PN 9
DURAFLO
ABS160
R11.5090.400
9
400.5
18.2
364.1
DN
375
S1
PN15
DURAFLO
ABS160
R11.5150.400
15
400.5
29.5
341.5
*DN
400
S1
PN 6
DURAFLO
ABS160
R11.5060.450
6
450.5
13.9
422.7
*DN
400
S1
PN 9
DURAFLO
ABS160
R11.5090.450
9
450.5
20.5
409.6
DN
400
S1
PN15
DURAFLO
ABS160
R11.5150.450
12
450.5
33.2
384.1
*DN
450
S1
PN 6
DURAFLO
ABS160
R11.5060.500
6
500.5
15.4
469.7
DN
450
S1
PN 9
DURAFLO
ABS160
R11.5090.500
9
500.5
22.7
456.0
*DN
450
S1
PN12
DURAFLO
ABS160
R11.5120.500
12
500.5
29.8
441.0
*DN
500
S1
PN 6
DURAFLO
ABS160
R11.5060.560
6
560.5
17.2
526.0
*DN
500
S1
PN 9
DURAFLO
ABS160
R11.5090.560
9
560.5
25.4
509.6
*DN
500
S1
PN12
DURAFLO
ABS160
R11.5120.560
12
560.5
33.3
493.9
*DN
575
S1
PN 6
DURAFLO
ABS160
R11.5060.630
6
630.6
19.4
591.8
575
S1
PN 9
DURAFLO
ABS160
R11.5090.630
9
630.6
28.6
573.4
575
S1
PN12
DURAFLO
ABS160
R11.5120.630
12
630.6
37.5
555.7
*DN
650
S1
PN 6
DURAFLO
ABS160
R11.5060.710
6
710.7
21.8
667.0
*DN
650
S1
PN 9
DURAFLO
ABS160
R11.5090.710
9
710.7
32.2
646.2
*DN
750
S2
PN 6
DURAFLO
ABS160
R11.5060.826
6
825.6
25.3
774.9
*DN
750
S2
PN 9
DURAFLO
ABS160
R11.5090.826
9
825.6
37.4
750.8
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
DN
*DN
* Denotes Non-Stockable
PIPE COMPLIES WITH AS/NZS 3518:2004
All values quoted are subject to manufacturing tolerances. Standard pipe length supplied 5.8m. Other lengths and pressure ratings are available upon request.
Pipe is supplied plain ended.
9
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
PLAIN SOCKET
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
SIZE
ID
A
B
Z
PN
(mm)
(mm)
(mm)
(mm)
RATING
DN 15 S1
R 01.100.015
21
27
43
9
15
DN 20 S1
R 01.100.020
27
33
47
7
15
DN 25 S1
R 01.100.025
34
41
53
7
15
DN 32 S1
R 01.100.032
42
52
61
7
15
DN 40 S1
R 01.100.040
48
59
65
5
15
DN 50 S1
R 01.100.050
60
74
77
5
15
DN 65 S1
R 01.100.065
75
93
91
3
15
DN 80 S1
R 01.100.080
89
110
112
10
15
DN 100 S1
R 01.100.100
114
141
138
10
15
DN 125 S1
R 01.100.125
140
168
165
12
15
DN 150 S1
R 01.100.150
168
204
192
12
15
DN 200 S1
R 11.100.225
225
250
246
8
12
DN 225 S1
R 11.100.250
250
280
271
9
12
DN 300 S1
R 11.100.315
315
355
337
9
12
DN 350 S1
R 11.100.355
355
388
377
9
12
DN 375 S1
R 11.100.400
400
440
423
11
12
DN 400 S1
R 11.100.450
450
500
476
14
12
DN 450 S1
R 11.100.500
500
560
527
15
12
DN 500 S1
R 11.100.560
560
665
555
15
12
DN 575 S1
R 11.100.630
630
708
590
20
21
DN 650 S1
R 11.100.710
710
808
630
20
9
DN 750 S2
R 11.100.826
826
922
675
15
9
COMPLIES WITH AS/NZS 3518:2004
10
CODE
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
CODE 135 - TO SUIT ALL OTHER DRILLINGS
STUB FLANGE
SIZE
DN 50 S1
CODE
R01.***.050
ID
A
B
C
D
Z
D*
A*
PN
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
RATING
60
96
40
14
74
3
74
96
15
DN 65 S1
R01.***.065
75
106
47
10
90
3
90
106
15
DN 80 S1
R01.***.080
89
127
57
18
108
5
108
127
15
DN 100 S1
R01.***.100
114
159
70
20
134
5
134
156
15
DN 125 S1
R01.***.125
140
187
84
12
163
5
163
181
15
DN 150 S1
R01.***.150
168
214
100
24
192
8
192
214
15
DN 200 S1
R11.***.225
225
270
126
25
250
6
247
267
12
DN 225 S1
R11.***.250
250
334
138
30
305
6
301
330
12
DN 300 S1
R11.***.315
315
376
171
35
362
6
350
374
12
DN 350 S1
R11.***.355
355
440
191
37
415
6
395
420
12
DN 375 S1
R11.***.400
400
488
214
35
450
8
440
483
12
DN 400 S1
R11.***.450
450
548
331
110
506
100
492
538
12
DN 450 S1
R11.***.500
500
613
356
110
561
100
544
593
12
DN 500 S1
R11.***.560
560
665
282
50
615
12
598
647
12
DN 575 S1
R11.***.630
630
708
340
65
671
55
12
DN 650 S1
R11.***.710
710
808
325
70
770
20
9
DN 750 S2
R11.***.826
826
922
430
110
870
100
9
COMPLIES WITH AS/NZS 3518:2004
*CODE 134 - TO SUIT BACKING RING DRILLED TO JIS10K
SIZE
CODE
ID
A
B
C
D
Z
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
200
R11.138. 225
225
270
144
35
250
250
225
R11.138. 250
250
334
191
70
305
60
300
R11.138. 315
315
376
224
70
362
60
350
R11.138. 355
355
440
244
70
415
60
375
R11.138. 400
400
488
306
110
450
100
Technical Data
Size Range: DN 200 to DN 375
Temperature Range: -30°C to 60°C
Jointing Methods: Solvent cement
11
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
Traditional Stub Flanges
When using the new compact stub flanges
it will be important to determine what
equipment they are matching up to. Where
the flanges are being used with butterfly
valves you will need to check the cordal
diameter of the valve disc (the disc cord
dimension at the face of the valve) to determine if there will be a clash with the pipe
ID. Where this is likely to occur we have the
138 series stub flange which is designed to
take the potential clash into account
138 Series Stub Flange
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
FULL FACE FLANGE Table “E”
SIZE
DN 15 S1
CODE
R01.130.015
B
C
D
Z
D*
PN
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
RATING
21
95
23
10
30
3
30
15
DN 20 S1
R01.130.020
27
100
25
10
35
3
35
15
R01.130.025
34
115
28
10
43
3
43
15
DN 32 S1
R01.130.032
42
140
32
10
52
3
52
15
DN 40 S1
R01.130.040
48
150
34
10
62
3
62
15
DN 50 S1
R01.130.050
60
165
40
10
74
3
74
15
DN 80 S1
R01.130.080
89
200
57
12
108
5
108
15
DN 100 S1
R01.130.100
114
220
70
17
134
5
134
15
DN 150 S1
R01.130.150
168
285
100
22
192
8
192
15
CODE 317 - DRILLED TABLE D AS 2129:2000.
CODE 322 - DRILLED ANSI 150
*CODE 329 - DRILLED JIS10K
COMPLIES WITH AS/NZS 3518:2004
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
A
DN 25 S1
CODE 129 - Undrilled
12
ID
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
SHOULDER END
SIZE
CODE
ID
A
B
Z
PN
(mm)
(mm)
(mm)
(mm)
RATING
DN 50 S1
R01.954.050
60
74
70
33
15
DN 80 S1
R01.954.080
89
104
90
39
15
DN 100 S1
R01.954.100
114
141
108
45
15
DN 150 S1
R01.954.150
168
208
140
50
15
DN 200 S1
R11.954.225
225
269
170
51
12
DN 225 S1
R11.954.250
250
310
207
76
12
DN 300 S1
R11.954.315
315
355
245
81
12
DN 350 S1
R11.954.355
355
387
273
89
9
DN 375 S1
R11.954.400
400
450
307
101
9
DN 400 S1
R11.954.450
450
500
337
106
9
DN 450 S1
R11.954.500
500
560
367
111
9
COMPLIES WITH AS/NZS 3518:2004
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
13
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
SHOULDER STYLE COUPLING
TO SUIT PIPE
CODE
SIZE
Z
(mm)
(mm)
(mm)
DN 50 S1
R03.953.050
140
98
44
R03.953.080
175
131
46
DN 100 S1
R03.953.100
205
162
50
DN 150 S1
R03.953.150
275
214
52
DN 200 S1
R13.953.225
DN 225 S1
R13.953.250
410
348
69
DN 300 S1
R13.953.315
489
395
69
DN 350 S1
R13.953.355
555
448
76
DN 375 S1
R13.953.400
568
482
73
DN 400 S1
R13.953.450
619
539
79
DN 450 S1
R13.953.500
698
597
76
CASING - GALVANIZED IRON
GASKET - EDPM
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
B
DN 80 S1
MATERIAL -
14
A
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
BLANK FLANGE STUB STYLE
SIZE
CODE
A
B
(mm)
(mm)
DN 200
S1
R11.136.225
270
25
DN 225
S1
R11.136.250
334
34
DN 300
S1
R11.136.315
376
40
FOR LARGER SIZES STEEL PLATES ARE RECOMMENDED
* Requires a backing ring
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
15
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
BLANK FULL FACE FLANGE TABLE “E”
SIZE
B
(mm)
(mm)
R01.313.015
95
13
DN 20 S1
R01.313.020
100
13
DN 25 S1
R01.313.025
115
13
DN 32 S1
R01.313.032
140
13
DN 40 S1
R01.313.040
150
13
DN 50 S1
R01.313.050
165
13
DN 80 S1
R01.313.080
200
19
DN 100 S1
R01.313.100
220
19
DN 150 S1
R01.313.150
285
25
CODE 129 - Undrilled
CODE 325 - DRILLED ANSI 150
CODE 332 - DRILLED JIS10K
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
A
DN 15 S1
CODE 326 - DRILLED TABLE D / AS 2129:2000.
16
CODE
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
BLIND STEEL PLATE
SIZE
CODE
A
B
(mm)
(mm)
TABLE D*
TABLE E*
DN 50 S1
R03.***.050
150
8
10
DN 65 S1
R03.***.065
165
8
10
DN 80 S1
R03.***.080
185
10
11
DN 100 S1
R03.***.100
215
10
12
DN 125 S1
R03.***.125
255
13
14
DN 150 S1
R03.***.150
280
13
17
DN 200 S1
R13.***.225
335
13
19
DN 225 S1
R13.***.250
405
16
22
DN 300 S1
R13.***.315
455
19
25
DN 350 S1
R13.***.355
525
22
29
DN 375 S1
R13.***.400
580
22
32
DN 400 S1
R13.***.450
640
25
35
DN 450 S1
R13.***.500
705
29
38
DN 500 S1
R13.***.560
760
29
44
DN 575 S1
R13. ***.630
825
32
48
DN 650 S1
R13.***.710
910
35
51
DN 750 S2
R13.***.826
1060
41
54
STANDARD MATERIAL - HOT DIPPED GALVANISED MILD STEEL TO AS/NZS 4680:1999.
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
CODE 732 - DRILLED TABLE D / AS 2129:2000.
CODE 731 - DRILLED TABLE E / AS 2129:2000.
OTHER DRILLINGS AVAILABLE ON REQUEST
* when using blind steel plate it is recommended to use blind plastic liner as well.
17
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
BLIND ABS LINER
TO SUIT PIPE
CODE
SIZE
R01.***.050
150
3
DN 65 S1
R01.***.065
165
3
DN 80 S1
R01.***.080
185
3
DN 100 S1
R01.***.100
215
3
DN 125 S1
R01.***.125
255
3
DN 150 S1
R01.***.150
280
3
DN 200 S1
R11.***.225
335
3
DN 225 S1
R11.***.250
405
3
DN 300 S1
R11.***.315
455
3
DN 350 S1
R11.***.355
525
3
DN 375 S1
R11.***.400
580
3
DN 400 S1
R11.***.450
640
3
DN 450 S1
R11.***.500
705
3
DN 500 S1
R11.***.560
760
3
DN 575 S1
R11.***.630
825
3
DN 650 S1
R11.***.710
910
3
DN 750 S2
R11.***.826
1060
3
CODE 722 - DRILLED TABLE D / AS 2129:2000.
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
B
(mm)
DN 50 S1
STANDARD MATERIAL - ABS WHITE SHEET.
CODE 721 - DRILLED TABLE E / AS 2129:2000.
OTHER DRILLINGS AVAILABLE ON REQUEST
* to be used in conjunction with blind steel plate
18
A
(mm)
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
BACKING RING TABLE D
TABLE D AS 2129:2000
TO SUIT PIPE
CODE
SIZE
ID
A
B
(mm)
(mm)
(mm)
DN
PCD
NO OF
HOLE
(mm)
HOLES
(mm)
DN 15 S1
R03.415.015
34
95
6
15
67
4
14
DN 20 S1
R03.415.020
40
100
6
20
73
4
14
DN 25 S1
R03.415.025
48
115
6
25
83
4
14
DN 32 S1
R03.415.032
58
120
6
32
87
4
14
DN 40 S1
R03.415.040
64
135
6
40
98
4
14
DN 50 S1
R03.415.050
79
150
8
50
114
4
18
DN 65 S1
R03.415.065
92
165
8
65
127
4
18
DN 80 S1
R03.415.080
112
185
8
80
146
4
18
DN 100 S1
R03.415.100
139
215
8
100
178
4
18
DN 125 S1
R03.415.125
167
255
10
125
210
8
18
DN 150 S1
R03.415.150
196
280
10
150
235
8
18
DN 200 S1
R13.415.225
258
335
10
200
292
8
18
DN 225 S1
R13.415.250
310
405
20
250
356
8
22
DN 300 S1
R13.415.315
366
455
20
300
406
12
22
DN 350 S1
R13.415.355
420
525
20
350
470
12
26
R13.415.400
454
580
20
*400
521
12
26
R13.415.450
510
640
25
*450
584
12
26
*DN 450 S1
R13.415.500
565
705
30
*500
641
16
26
*DN 500 S1
R13.415.560
621
760
30
*550
699
16
30
*DN 575 S1
R13.415.630
675
825
32
*600
756
16
30
*DN 650 S1
R13.415.710
775
910
35
*700
845
20
30
*DN 750 S2
R13.415.826
902
1060
41
*800
984
20
36
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
*DN 375 S1
*DN 400 S1
STANDARD MATERIAL - HOT DIPPED GALVANISED MILD STEEL TO AS/NZS 4680:1999.
AVAILABLE IN STAINLESS STEEL ON REQUEST - CODE 422
OTHER DRILLINGS AVAILABLE ON REQUEST
*WHEN CONNECTING ABS SYSTEMS TO OTHER SYSTEMS PLEASE NOTE VARIATION BETWEEN ABS SYSTEM “DN”
DESIGNATION AND AS 2129 “DN” DESIGNATION
19
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
BACKING RING TABLE E
TABLE E AS 2129:2000
TO SUIT PIPE
CODE
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
SIZE
ID
A
B
(mm)
(mm)
(mm)
DN
PCD
NO OF
HOLE
(mm)
HOLES
(mm)
DN 15 S1
R03.416.015
34
95
6
15
67
4
14
DN 20 S1
R03.416.020
40
100
6
20
73
4
14
DN 25 S1
R03.416.025
48
115
6
25
83
4
14
DN 32 S1
R03.416.032
58
120
6
32
87
4
14
DN 40 S1
R03.416.040
64
135
6
40
98
4
14
DN 50 S1
R03.416.050
79
150
8
50
114
4
18
DN 65 S1
R03.416.065
92
165
8
65
127
4
18
DN 80 S1
R03.416.080
112
185
8
80
146
4
18
DN 100 S1
R03.416.100
139
215
8
100
178
8
18
DN 125 S1
R03.416.125
167
255
10
125
210
8
18
DN 150 S1
R03.416.150
196
280
10
150
235
8
22
DN 200 S1
R13.416.225
258
335
10
200
292
8
22
DN 225 S1
R13.416.250
310
405
20
250
356
12
22
DN 300 S1
R13.416.315
366
455
20
300
406
12
26
DN 350 S1
R13.416.355
420
525
20
350
470
12
26
*DN 375 S1
R13.416.400
454
580
20
*400
521
12
26
*DN 400 S1
R13.416.450
510
640
25
*450
584
16
26
*DN 450 S1
R13.416.500
565
705
30
*500
641
16
26
*DN 500 S1
R13.416.560
621
760
30
*550
699
16
30
*DN 575 S1
R13.416.630
675
825
32
*600
756
16
33
*DN 650 S1
R13.416.710
775
910
35
*700
845
20
33
*DN 750 S2
R13.416.826
902
1060
41
*800
984
20
36
STANDARD MATERIAL - HOT DIPPED GALVANISED MILD STEEL TO AS/NZS 4680:1999.
AVAILABLE IN STAINLESS STEEL ON REQUEST - CODE 420
OTHER DRILLINGS AVAILABLE ON REQUEST
*WHEN CONNECTING ABS SYSTEMS TO OTHER SYSTEMS PLEASE NOTE VARIATION BETWEEN ABS SYSTEM “DN”
DESIGNATION AND AS 2129 “DN” DESIGNATION
20
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
BACKING RING ANSI150
ANSI 150
TO SUIT PIPE
CODE
SIZE
ID
(mm)
A
B
(mm)
(mm)
DN
PCD
NO OF
HOLE
(mm)
HOLES
(mm)
DN 15 S1
R03.425.015
34
95
6
15
60
4
15
DN 20 S1
R03.425.020
40
100
6
20
70
4
15
DN 25 S1
R03.425.025
48
115
6
25
79
4
15
DN 32 S1
R03.425.032
58
120
6
32
89
4
15
DN 40 S1
R03.425.040
64
135
6
40
98
4
15
DN 50 S1
R03.425.050
79
150
8
50
121
4
18
DN 65 S1
R03.425.065
92
165
8
65
140
4
18
DN 80 S1
R03.425.080
112
185
8
80
152
4
18
DN 100 S1
R03.425.100
139
215
8
100
191
8
18
DN 125 S1
R03.425.125
167
255
10
125
216
8
21
DN 150 S1
R03.425.150
196
280
10
150
241
8
21
DN 200 S1
R13.425.225
258
335
10
200
298
8
21
DN 225 S1
R13.425.250
310
405
20
250
362
12
25
DN 300 S1
R13.425.315
366
455
20
300
432
12
25
DN 350 S1
R13.425.355
420
525
20
350
476
12
28
DN 375 S1
R13.425.400
454
580
20
400
540
16
30
STANDARD MATERIAL - HOT DIPPED GALVANISED MILD STEEL TO AS/NZS 4680:1999.
AVAILABLE IN STAINLESS STEEL ON REQUEST - CODE 430
OTHER DRILLINGS AVAILABLE ON REQUEST
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
21
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
BACKING RING JIS10K
JIS 10K
TO SUIT PIPE
CODE
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
SIZE
ID
A
B
(mm)
(mm)
(mm)
DN
PCD
NO OF
HOLE
(mm)
HOLES
(mm)
DN 15 S1
R03.413.015
34
95
6
15
70
4
14
DN 20 S1
R03.413.020
40
100
6
20
75
4
14
DN 25 S1
R03.413.025
48
125
6
25
90
4
18
DN 32 S1
R03.413.032
58
135
6
32
100
4
18
DN 40 S1
R03.413.040
64
140
6
40
105
4
18
DN 50 S1
R03.413.050
79
155
8
50
120
4
18
DN 65 S1
R03.413.065
92
175
8
65
140
4
18
DN 80 S1
R03.413.080
112
185
8
80
150
8
18
DN 100 S1
R03.413.100
139
210
8
100
175
8
18
DN 125 S1
R03.413.125
167
250
10
125
210
8
22
DN 150 S1
R03.413.150
196
280
10
150
240
8
22
DN 200 S1
R13.413.225
258
330
10
200
290
12
22
DN 225 S1
R13.413.250
310
400
20
250
355
12
24
DN 300 S1
R13.413.315
366
445
20
300
400
16
24
DN 350 S1
R13.413.355
420
490
20
350
445
16
24
*DN 375 S1
R13.413.400
454
560
20
*400
510
16
26
*DN 400 S1
R13.413.450
510
620
25
*450
565
20
26
*DN 450 S1
R13.413.500
565
675
30
*500
620
20
26
*DN 500 S1
R13.413.560
621
745
30
*550
680
20
32
STANDARD MATERIAL - HOT DIPPED GALVANISED MILD STEEL TO AS/NZS 4680:1999.
AVAILABLE IN STAINLESS STEEL ON REQUEST - CODE 445
OTHER DRILLINGS AVAILABLE ON REQUEST
*WHEN CONNECTING ABS SYSTEMS TO OTHER SYSTEMS PLEASE NOTE VARIATION BETWEEN ABS SYSTEM “DN”
DESIGNATION AND JIS 10K “DN” DESIGNATION
22
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
VALVE SUPPORT PLATE
TO SUIT PIPE
CODE
SIZE
A
B
C
D
E
F
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
DN 15 S1
R03.***.015
95
86
51
14
16
8
DN 20 S1
R03.***.020
100
89
76
14
16
8
DN 25 S1
R03.***.025
115
95
76
14
16
8
DN 32 S1
R03.***.032
120
99
76
14
16
8
DN 40 S1
R03.***.040
135
105
76
14
16
8
DN 50 S1
R03.***.050
150
127
102
14
22
8
DN 65 S1
R03.***.065
165
143
115
14
22
8
DN 80 S1
R03.***.080
185
143
126
14
22
8
DN 100 S1
R03.***.100
215
159
152
14
22
8
DN 125 S1
R03.***.125
255
185
190
14
30
10
DN 150 S1
R03.***.150
280
216
230
18
33
10
DN 200 S1
R13.***.225
335
248
280
18
33
10
DN 225 S1
R13.***.250
405
298
340
22
40
12
DN 300 S1
R13.***.315
455
348
390
22
40
12
STANDARD MATERIAL - HOT DIPPED GALVANISED MILD STEEL TO AS/NZS 4680
CODE 465 - DRILLED TABLE D / AS 2129:2000.
CODE 460 - DRILLED TABLE E / AS 2129:2000.
CODE 470 - DRILLED TO ANSI 150
OTHER DRILLINGS AVAILABLE ON REQUEST
AVAILABLE IN STAINLESS STEEL ON REQUEST.
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
23
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
GASKET (FULL FACE STYLE)
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
SIZE
CODE
A
B
(mm)
(mm)
DN 15 S1
R04.***.015
22
95
3
DN 20 S1
R04.***.020
28
100
3
DN 25 S1
R04.***.025
35
115
3
DN 32 S1
R04.***.032
43
120
3
DN 40 S1
R04.***.040
49
135
3
DN 50 S1
R04.***.050
61
150
3
DN 80 S1
R04.***.080
90
185
3
DN 100 S1
R04.***.100
115
215
3
DN 150 S1
R04.***.150
169
280
3
DN 200 S1
R14.***.225
226
335
8
DN 225 S1
R14.***.250
251
405
8
DN 300 S1
R14.***.315
316
455
8
DN 350 S1
R14.***.355
356
535
8
DN 375 S1
R14.***.400
401
580
8
DN 400 S1
R14.***.450
451
640
8
DN 450 S1
R14.***.500
501
705
8
DN 500 S1
R14.***.560
561
760
8
DN 575 S1
R14.***.630
631
825
8
DN 650 S1
R14.***.710
711
910
8
DN 750 S2
R14.***.826
827
1060
8
STANDARD MATERIAL - EDPM. OTHER MATERIALS ARE AVAILABLE ON REQUEST
CODE 409 - DRILLED TABLE D* / AS 2129:2000.
CODE 410 - DRILLED TABLE E* / AS 2129:2000.
CODE 426 - DRILLED TO ANSI 150*
OTHER DRILLINGS AVAILABLE ON REQUEST
*SEE NOTES AND DRILLING DETAILS ON PAGES 19, 20, 21 & 22
24
ID
(mm)
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
GASKET (STUB FLANGE STYLE)
SIZE
CODE
ID
A
B
(mm)
(mm)
(mm)
DN 50 S1
R04.431.050
61
97
3
DN 65 S1
R04.431.065
76
105
3
DN 80 S1
R04.431.080
90
129
3
DN 100 S1
R04.431.100
115
161
3
DN 125 S1
R04.431.125
141
187
3
DN 150 S1
R04.431.150
169
214
3
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
25
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
ELBOW 90º
SIZE
CODE
ID
B
Z
PN
(mm)
(mm)
(mm)
RATING
DN 15 S1
R01.115.015
21
31
11
15
DN 20 S1
R01.115.020
27
36
14
15
DN 25 S1
R01.115.025
34
43
18
15
DN 32 S1
R01.115.032
42
51
22
15
DN 40 S1
R01.115.040
48
56
25
15
DN 50 S1
R01.115.050
60
69
32
15
DN 65 S1
R01.115.065
75
83
39
15
DN 80 S1
R01.115.080
89
102
50
15
DN 100 S1
R01.115.100
114
147
71
15
DN 125 S1
R01.115.125
140
180
96
15
DN 150 S1
R01.115.150
168
180
88
15
DN 200 S1
R11.115.225
225
235
116
12
DN 225 S1
R11.115.250V
250
258
127
12
DN 300 S1
R11.115.315V
315
322
158
12
DN 350 S1
R11.115.355R
355
507
323
9
DN 375 S1
R11.115.400V
400
507
300
9
COMPLIES WITH AS/NZS 3518:2004
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
ELBOW DN350 IS MANUFACTURED FROM ELBOW DN375 FITTED WITH DN375-DN350 REDUCING BUSHES
FOR DN200 AND ABOVE, ELBOWS WITH HIGHER PRESSURE RATINGS ARE AVAILABLE.
THEY ARE MANUFACTURED FROM ABS LAYERED WITH GLASS REINFORCED EPOXY AND ARE DESIGNED AND MANUFACTURED IN ACCORDANCE TO EURAPIPE INTERNAL QUALITY AND MANUFACTURING
PROCEDURES AND SPECIFICATIONS AND TYPE TESTED AT 3.2 TIMES THE DESIGN PRESSURE.
26
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
ELBOW 45º
SIZE
CODE
ID
B
Z
PN
(mm)
(mm)
(mm)
RATING
DN 15 S1
R01.119.015
21
27
7
15
DN 20 S1
R01.119.020
27
30
8
15
DN 25 S1
R01.119.025
34
35
10
15
DN 32 S1
R01.119.032
42
42
13
15
DN 40 S1
R01.119.040
48
45
14
15
DN 50 S1
R01.119.050
60
54
17
15
DN 65 S1
R01.119.065
75
61
17
15
DN 80 S1
R01.119.080
89
74
21
15
DN 100 S1
R01.119.100
114
94
28
15
DN 125 S1
R01.119.125
140
107
31
15
DN 150 S1
R01.119.150
168
132
40
15
DN 200 S1
R11.119.225V
225
171
52
12
DN 225 S1
R11.119.250V
250
190
58
12
DN 300 S1
R11.119.315V
315
232
68
12
DN 350 S1
R11.119.355R
355
294
110
9
DN 375 S1
R11.119.400V
400
294
87
9
COMPLIES WITH AS/NZS 3518:2004
ELBOW DN350 IS MANUFACTURED FROM ELBOW DN375 FITTED WITH DN375-DN350 REDUCING BUSHES
27
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
FOR DN200 AND ABOVE, ELBOWS WITH HIGHER PRESSURE RATINGS ARE AVAILABLE.
THEY ARE MANUFACTURED FROM ABS LAYERED WITH GLASS REINFORCED EPOXY AND ARE DESIGNED AND MANUFACTURED IN ACCORDANCE TO EURAPIPE INTERNAL QUALITY AND MANUFACTURING
PROCEDURES AND SPECIFICATIONS AND TYPE TESTED AT 3.2 TIMES THE DESIGN PRESSURE.
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
FAUCET ELBOW 90º
SIZE
SIZE
SW SOCKET
THREADED
DN 15 S1
1/2” BSP
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
R01.116.015
A
B
C
D
ID
Z
PN
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
RATING
29
29
31
18
21
11
15
DN 20 S1
3/4” BSP
R01.116.020
35
35
36
21
27
14
15
DN 25 S1
1” BSP
R01.116.025
44
42
43
24
34
18
15
DN 20 S1
1/2” BSP
R01.116.020015
35
32
36
18
27
14
15
COMPLIES WITH AS/NZS 3518:2004
28
CODE
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
MOULDED BEND 90º
SIZE
CODE
ID
A
B
C
L
PN
(mm)
(mm)
(mm)
(mm)
(mm)
RATING
DN 15 S1
R01.118.015
21
29
40
58
20
15
DN 20 S1
R01.118.020
27
35
50
71
22
15
DN 25 S1
R01.118.025
34
43
64
88
25
15
DN 32 S1
R01.118.032
42
54
80
109
29
15
DN 40 S1
R01.118.040
48
64
100
131
31
15
DN 50 S1
R01.118.050
60
76
126
163
37
15
DN 65 S1
R01.118.065
75
93
150
195
44
15
DN 80 S1
R01.118.080
89
113
180
231
53
15
DN 100 S1
R01.118.100
114
137
220
284
65
15
COMPLIES WITH AS/NZS 3518:2004
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
29
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
BEND 90º R=1.2D (So- So)
SIZE
CODE
A
B
PN
(mm)
min(mm)
RATING
DN 400 S1 PN 9
R11.305090.450
1142
1387
9
DN 450 S1 PN 9
R11.305090.500
1235
1506
9
DN 500 S1 PN 9
R11.305090.560
1272
1557
9
DN 575 S1 PN 9
R11.305090.630
1300
1605
9
DN 650 S1 PN 9
R11.305090.710
1593
1918
9
DN 750 S2 PN 9
R11.305090.826
1752
2097
9
A=MINIMUM LEG LENGTH
MANUFACTURING TOLERANCES APPLY
OTHER ANGLES ARE AVAILABLE UPON REQUEST
THE FOLLOWING ADDITIONAL BEND PRESSURE RATINGS ARE AVAILABLE UPON REQUEST:
CODE 305045
PN 4.5
CODE 305060
PN 6
CODE 305120
PN 12
THE BENDS ARE MANUFACTURED FROM ABS LAYERED WITH GLASS REINFORCED EPOXY.
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
THEY ARE DESIGNED AND MANUFACTURED IN ACCORDANCE TO EURAPIPE INTERNAL QUALITY AND MANUFACTURING PROCEDURES AND SPECIFICATIONS AND TYPE TESTED AT 3.2 TIMES THE DESIGN
PRESSURE.
30
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
BEND 45º R=1.2D (So- So)
SIZE
CODE
A
B
PN
(mm)
min(mm)
RATING
DN 400 S1 PN 9
R11.304090.450
878
1123
9
DN 450 S1 PN 9
R11.304090.500
969
1241
9
DN 500 S1 PN 9
R11.304090.560
1134
1419
9
DN 575 S1 PN 9
R11.304120.630
1153
1458
9
DN 650 S1 PN 9
R11.304090.710
1429
1754
9
DN 750 S2 PN 9
R11.304090.826
1396
1741
9
A=MINIMUM LEG LENGTH
MANUFACTURING TOLERANCES APPLY
OTHER ANGLES ARE AVAILABLE UPON REQUEST
THE FOLLOWING ADDITIONAL BEND PRESSURE RATINGS ARE AVAILABLE UPON REQUEST:
CODE 304045
PN 4.5
CODE 304060
PN 6
CODE 304120
PN 12
THE BENDS ARE MANUFACTURED FROM ABS LAYERED WITH GLASS REINFOCED EPOXY.
THEY ARE DESIGNED AND MANUFACTURED IN ACCORDANCE TO EURAPIPE INTERNAL QUALITY AND MANUFACTURING PROCEDURES AND SPECIFICATIONS AND TYPE TESTED AT 3.2 TIMES THE DESIGN
PRESSURE.
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
31
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
BEND 90º SHORT RADIUS R=2.5D (Sp- Sp)
SIZE
CODE
A
B
PN
(mm)
min(mm)
RATING
DN 50 S1 PN 15
R01.308150.050
208
251
15
DN 65 S1 PN 15
R01.308150.065
252
288
15
DN 80 S1 PN 15
R01.308150.080
295
327
15
DN 100 S1 PN 15
R01.308150.100
371
416
15
DN 125 S1 PN 15
R01.308150.125
447
503
15
DN 150 S1 PN 15
R01.308150.150
532
604
15
DN 200 S1 PN 9
R11.308090.225
800
947
9
DN 225 S1 PN 9
R11.308090.250
887
960
9
DN 300 S1 PN 9
R11.308090.315
1115
1215
9
DN 350 S1 PN 9
R11.308090.355
1255
1355
9
DN 375 S1 PN 9
R11.308090.400
1411
1511
9
DN 400 S1 PN 9
R11.308090.450
1586
1686
9
*DN 450 S1 PN 9
R11.308090.500
2019
2290
9
A=MINIMUM LEG LENGTH
MANUFACTURING TOLERANCES APPLY
OTHER ANGLES ARE AVAILABLE UPON REQUEST
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
THE FOLLOWING ADDITIONAL BEND PRESSURE RATINGS ARE AVAILABLE UPON REQUEST:
ALL SIZES
CODE 308045
ALL SIZES
CODE 308060
DN50 TO DN150
CODE 308120
* DN450 BENDS ARE MANUFACTURED FROM ABS LAYERED WITH GLASS REINFOCED EPOXY AND ARE SUPPLYED COMPLETE WITH SOCKETS AT BOTH ENDS. THEY ARE DESIGNED AND MANUFACTURED
IN ACCORDANCE TO EURAPIPE INTERNAL QUALITY AND MANUFACTURING PROCEDURES AND SPECIFICATIONS AND TYPE TESTED AT 3.2 TIMES THE DESIGN PRESSURE.
Bends supplied plain ended, require sockets or Stub & B/Ring for joining.
32
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
BEND 45º SHORT RADIUS R=2.5D (Sp- Sp)
SIZE
CODE
A
B
PN
(mm)
min(mm)
RATING
DN 50 S1 PN 15
R01.312150.050
119
212
15
DN 65 S1 PN 15
R01.312150.065
142
254
15
DN 80 S1 PN 15
R01.312150.080
165
267
15
DN 100 S1 PN 15
R01.312150.100
203
318
15
DN 125 S1 PN 15
R01.312150.125
241
385
15
DN 150 S1 PN 15
R01.312150.150
286
434
15
DN 200 S1 PN 12
R11.312120.225
471
753
12
DN 225 S1 PN 12
R11.312120.250
521
839
12
DN 300 S1 PN 12
R11.312120.315
654
936
12
DN 350 S1 PN 12
R11.312120.355
736
1083
12
DN 375 S1 PN 12
R11.312120.400
826
1214
12
DN 400 S1 PN 12
R11.312120.450
928
1374
12
*DN 450 S1 PN 12
R11.312120.500
2050
1678
12
A=MINIMUM LEG LENGTH
MANUFACTURING TOLERANCES APPLY
OTHER ANGLES ARE AVAILABLE UPON REQUEST
THE FOLLOWING ADDITIONAL BEND PRESSURE RATINGS ARE AVAILABLE UPON REQUEST:
CODE 312045
PN 4.5
CODE 312060
PN 6
CODE 312090
PN 9
33
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
* DN450 BENDS ARE MANUFACTURED FROM ABS LAYERED WITH GLASS REINFOCED EPOXY AND ARE SUPPLYED COMPLETE WITH SOCKETS AT BOTH ENDS. THEY ARE DESIGNED AND MANUFACTURED
IN ACCORDANCE TO EURAPIPE INTERNAL QUALITY AND MANUFACTURING PROCEDURES AND SPECIFICATIONS AND TYPE TESTED AT 3.2 TIMES THE DESIGN PRESSURE.
Bends supplied plain ended, require sockets or Stub & B/Ring for joining.
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
BEND 90º LONG RADIUS R= 5D (Sp-Sp)
SIZE
CODE
PN
RATING
R01.309150.050
357
570
15
DN 65 S1 PN 15
R01.309150.065
439
845
15
DN 80 S1 PN 15
R01.309150.080
523
870
15
DN 100 S1 PN 15
R01.309150.100
655
950
15
DN 125 S1 PN 15
R01.309150.125
796
970
15
DN 150 S1 PN 15
R01.309150.150
952
1165
15
DN 200 S1 PN 12
R11.309120.225
1264
1495
12
DN 225 S1 PN 12
R11.309120.250
1401
1615
12
DN 300 S1 PN 12
R11.309120.315
1758
2024
12
DN 350 S1 PN 12
R11.309120.355
1978
2274
12
DN 375 S1 PN 12
R11.309120.400
2226
2600
12
OTHER ANGLES AND PRESSURE RATINGS ARE AVAILABLE UPON REQUEST
* Bends supplied plain ended, require sockets or Stub & B/Ring for joining.
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
B
min(mm)
DN 50 S1 PN 15
A=MINIMUM LEG LENGTH
MANUFACTURING TOLERANCES APPLY
34
A
(mm)
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
BEND 45º LONG RADIUS R=5D (Sp-Sp)
SIZE
CODE
A
B
PN
(mm)
min(mm)
RATING
DN 50 S1 PN 15
R01.310150.050
181
514
15
DN 65 S1 PN 15
R01.310150.065
219
756
15
DN 80 S1 PN 15
R01.310150.080
259
776
15
DN 100 S1 PN 15
R01.310150.100
321
806
15
DN 125 S1 PN 15
R01.310150.125
386
830
15
DN 150 S1 PN 15
R01.310150.150
460
968
15
DN 200 S1 PN 12
R11.310120.225
605
1276
12
DN 225 S1 PN 12
R11.310120.250
668
1357
12
DN 300 S1 PN 12
R11.310120.315
836
1622
12
DN 350 S1 PN 12
R11.310120.355
939
1870
12
DN 375 S1 PN 12
R11.310120.400
1054
2078
12
A=MINIMUM LEG LENGTH
MANUFACTURING TOLERANCES APPLY
OTHER ANGLES AND PRESSURE RATINGS ARE AVAILABLE UPON REQUEST
* Bends supplied plain ended, require sockets or Stub & B/Ring for joining.
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
35
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
EQUAL TEE (So-SoxSo)
SIZE
CODE
ID
A
B
L
Z
(mm)
(mm)
(mm)
(mm)
(mm)
TYPE
PN
RATING
DN 15 S1
R01.122.015
21
63
31
20
11
M
15
DN 20 S1
R01.122.020
27
72
36
22
14
M
15
DN 25 S1
R01.122.025
34
85
43
25
18
M
15
DN 32 S1
R01.122.032
42
102
51
29
22
M
15
DN 40 S1
R01.122.040
48
112
56
31
25
M
15
DN 50 S1
R01.122.050
60
137
69
37
32
M
15
DN 65 S1
R01.122.065
75
166
83
44
39
M
15
DN 80 S1
R01.122.080
89
204
102
53
49
M
15
DN 100 S1
R01.122.100
114
258
129
65
64
M
15
DN 125 S1
R01.122.125
140
298
149
76
73
F
15
DN 150 S1
R01.122.150
168
360
180
92
88
M
15
DN 200 S1
R11.122.225V
225
463
232
119
113
M
12
DN 225 S1
R11.122.250V
250
526
263
131
132
M
12
DN 300 S1
R11.122.315V
315
644
322
164
158
M
12
DN 350 S1
R11.122.355
355
840
420
184
236
F
6
DN 375 S1
R11.122.400V
400
840
420
206
214
M
6
COMPLIES WITH AS/NZS 3518:2004
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
TEE DN350 IS MANUFACTURED FROM TEE DN375 FITTED WITH DN375-DN350 REDUCING BUSHES
FOR DN200 AND ABOVE, TEES WITH HIGHER PRESSURE RATINGS ARE AVAILABLE.
THEY ARE MANUFACTURED FROM ABS LAYERED WITH GLASS REINFORCED EPOXY AND ARE DESIGNED AND MANUFACTURED IN ACCORDANCE TO EURAPIPE INTERNAL QUALITY AND MANUFACTURING
PROCEDURES AND SPECIFICATIONS AND TYPE TESTED AT 3.2 TIMES THE DESIGN PRESSURE.
36
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
REDUCING TEE SPIGOT OFFTAKE (So-SoxSp)
SIZE
CODE
ID
A
B
C
L
PN
(mm)
(mm)
(mm)
(mm)
(mm)
RATING
DN 200–DN 150
R11.120.225150
225
315
500
250
120
12
DN 225–DN 150
R11.120.250150
250
339
500
325
131
12
DN 300–DN 200
R11.120.315225
315
400
650
375
164
12
DN 350–DN 225
R11.120.355250
355
450
720
450
184
12
DN 375–DN 225
R11.120.400250
400
500
800
450
206
12
DN 400–DN 350
R11.120.450355
450
560
920
657
231
12
DN 450–DN 350
R11.120.500355
500
613
1000
575
256
12
DN 500–DN 375
R11.120.560400
560
665
1200
625
270
12
DN 575–DN 375
R11.120.630400
630
708
1300
625
285
12
DN 650–DN 400
R11.120.710450
710
808
1400
680
305
9
DN 750–DN 450
R11.120.826500
826
922
1500
775
330
9
COMPLIES WITH AS/NZS 3518:2004
MAXIMUM ALLOWABLE SPIGOT DIAMETER IS SHOWN.
REDUCERS TO SMALLER DIAMETER SPIGOTS ARE AVAILABLE UPON REQUEST
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
37
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
REDUCING TEE SOCKET OFFTAKE (So-SoxSo)
SIZE
DN 20–DN 15
CODE
R01.122.020015
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
B
C
ID1
ID2
Z1
Z2
PN
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
RATING
33
67
34
27
21
12
14
15
DN 25–DN 15
R01.122.025015
41
73
38
34
21
12
18
15
DN 25–DN 20
R01.122.025020
41
78
40
34
27
14
18
15
DN 40–DN 25
R01.122.040025
59
97
50
48
34
18
25
15
DN 50–DN 25
R01.122.050025
74
109
56
60
34
18
31
15
DN 50–DN 40
R01.122.050040
74
125
62
60
48
26
31
15
COMPLIES WITH AS/NZS 3518:2004
38
A
(mm)
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
TEE THREADED OFF TAKE (So-SoxTh)
SIZE
SIZE
SW SOCKET
THREADED
DN 15 S1
1/2” BSP
DN 20 S1
DN 20 S1
CODE
ID
A
B
C
D
Z
PN
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
RATING
R01.121.015
21
29
63
29
18
11
15
1/2” BSP
R01.121.020015
27
35
67
32
18
12
15
3/4” BSP
R01.121.020
27
44
72
35
21
14
15
DN 25 S1
1/2” BSP
R01.121.025015
34
35
73
35
18
12
15
DN 25 S1
1” BSP
R01.121.025
34
44
85
42
24
18
15
COMPLIES WITH AS/NZS 3518:2004
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
39
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
Y PIECE 45º
SIZE
DN 20 S1
CODE
R01.128.020
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
B
C
Z1
Z2
Z3
(mm)
(mm)
(mm)
(mm)
(mm)
27
68
43
34
26
6
TYPE*
PN
RATING
M
15
DN 25 S1
R01.128.025
34
81
52
55
29
7
M
15
DN 32 S1
R01.128.032
42
98
65
52
42
9
M
15
DN 40 S1
R01.128.040
48
117
77
65
51
11
M
15
DN 50 S1
R01.128.050
60
140
95
78
63
12
M
15
DN 80 S1
R01.128.080
89
290
203
189
152
27
F
6
DN 100 S1
R01.128.100
114
596
373
469
310
170
F
6
DN 150 S1
R01.128.150
168
814
495
634
405
229
F
6
COMPLIES WITH AS/NZS 3518:2004
40
ID
(mm)
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
SADDLE STRIPS
SIZE
CODE
∝
A
(º)
D*
(mm)
DN 80 S1
R01.146.080
120º
300
1/2”
DN 100 S1
R01.146.100
120º
300
1”
DN 125 S1
R01.146.125
120º
300
1”
DN 150 S1
R01.146.150
120º
300
1 1/4”
DN 200 S1
R11.146.225
60º
300
1 1/4”
DN 225 S1
R11.146.250
60º
300
1 1/2”
DN 300 S1
R11.146.315
60º
300
1 1/2”
DN 350 S1
R11.146.355
60º
300
1 1/2”
DN 375 S1
R11.146.400
60º
300
1 1/2”
DN 400 S1
R11.146.450
60º
300
1 1/2”
DN 450 S1
R11.146.500
60º
300
1 1/2”
D-MAXIMUM SIZE OF THE THREADED TAPPING
* Saddle Strip Supplied with Stainless Steel Straps
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
41
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
TAPPING SADDLES
SIZE
SIZE
MAIN
OFFTAKE
DN 80 S1
DN 50 S1
DN 100 S1
DN 50 S1
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
COMPLIES WITH AS/NZS 3518:2004
42
CODE
A
B
ID1
ID2
C
D
L
PN
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
RATING
R01.127.080050
150
96
89
60
145
90
37
9
R01.127.100050
175
108
114
60
170
100
37
9
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
REDUCING SOCKET
SIZE
CODE
A
A1
B
ID
ID1
L
L1
Z
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
TYPE
PN
RATING
R01.114.020015
34
27
46
27
21
22
20
4
M
15
DN 25 - DN 15 S1
R01.114.025015
42
27
52
34
21
25
20
7
M
15
DN 25 - DN 20 S1
R01.114.025020
42
34
52
34
27
25
22
5
M
15
DN 32 - DN 25 S1
R01.114.032025
52
43
64
42
34
29
25
10
M
15
DN 40 - DN 25 S1
R01.114.040025
59
43
71
48
34
31
25
15
M
15
DN 40 - DN 32 S1
R01.114.040032
59
52
68
48
42
31
29
8
M
15
DN 50 - DN 40 S1
R01.114.050040
74
62
81
60
48
37
31
13
M
15
DN 65 - DN 50 S1
R01.114.065050
93
94
94
75
60
44
37
9
F
15
DN 80 - DN 50 S1
R01.114.080050
110
74
112
89
60
53
37
23
M
15
DN 80 - DN 65 S1
R01.114.080065
110
112
112
89
75
53
44
17
F
15
DN 100 - DN 80 S1
R01.114.100080
134
108
133
114
89
65
53
29
M
15
DN 125 - DN 100 S1
R01.114.125100
173
165
165
140
114
76
65
32
F
9
DN 150 - DN 100 S1
R01.114.150100
204
141
204
168
114
92
65
51
M
15
DN 150 - DN 125 S1
R01.114.150125
204
192
192
168
140
92
76
19
F
15
DN 200 - DN 150 S1
R11.114.225150
247
-
246
225
168
119
92
35
F
12
DN 200 - DN 195 S1
R11.114.225195
247
-
246
225
219
119
116
20
F
12
DN 225 - DN 200 S1
R11.114.250225
275
-
271
250
225
131
119
21
F
12
DN 300 - DN 225 S1
R11.114.315250
344
−
357
315
250
164
131
39
F
12
DN 350 - DN 300 S1
R11.114.355315
388
-
377
355
315
184
164
26
F
9
DN 375 - DN 350 S1
R11.114.400355
440
-
423
400
355
206
184
30
F
9
DN 400 - DN 375 S1
R11.114.450400
493
-
476
450
400
231
206
35
F
9
DN 450 - DN 400 S1
R11.114.500450
548
-
527
500
450
256
231
35
F
9
DN 500 - DN 450 S1
R11.114.560500
612
-
555
560
500
270
256
12
F
9
DN 575 - DN 500 S1
R11.114.630560
708
-
590
630
560
285
270
51
F
9
DN 650 - DN 575 S1
R11.114.710630
808
-
625
710
630
305
285
45
F
9
DN 750 - DN 650 S2/S1
R11.114.826710
922
-
675
826
710
330
305
30
F
9
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
DN 20 - DN 15 S1
COMPLIES WITH AS/NZS 3518:2004
43
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
REDUCING BUSH
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
SIZE
ID
A
B
Z
PN
(mm)
(mm)
(mm)
(mm)
RATING
DN 20 - DN 15 S1
R01.109.020015
21
27
22
2
15
DN 25 - DN 15 S1
R01.109.025015
21
34
25
5
15
DN 25 - DN 20 S1
R01.109.025020
27
34
25
3
15
DN 32 - DN 15 S1
R01.109.032015
21
42
29
9
15
DN 32 - DN 20 S1
R01.109.032020
27
42
29
7
15
DN 32 - DN 25 S1
R01.109.032025
34
42
29
4
15
DN 40 - DN 15 S1
R01.109.040015
21
48
31
11
15
DN 40 - DN 20 S1
R01.109.040020
27
48
31
9
15
DN 40 - DN 25 S1
R01.109.040025
34
48
31
6
15
DN 40 - DN 32 S1
R01.109.040032
42
48
31
2
15
DN 50 - DN 25 S1
R01.109.050025
34
60
37
12
15
DN 50 - DN 32 S1
R01.109.050032
42
60
37
8
15
DN 50 - DN 40 S1
R01.109.050040
48
60
37
6
15
DN 65 - DN 50 S1
R01.109.065050
60
75
44
8
15
DN 80 - DN 20 S1
R01.109.080020
27
89
52
30
15
DN 80 - DN 40 S1
R01.109.080040
48
89
52
21
15
DN 80 - DN 50 S1
R01.109.080050
60
89
52
15
15
DN 80 - DN 65 S1
R01.109.080065
75
89
52
6
15
DN 100 - DN 50 S1
R01.109.100050
60
114
64
28
15
DN 100 - DN 80 S1
R01.109.100080
89
114
64
13
15
DN 125 - DN 100 S1
R01.109.125100
114
140
83
20
15
DN 150 - DN 100 S1
R01.109.150100
114
168
92
27
15
DN 150 - DN 125 S1
R01.109.150125
140
168
92
7
15
DN 200 - DN 150 S1
R11.109.225150
168
225
120
29
12
DN 225 - DN 200 S1
R11.109.250225
225
250
131
12
12
DN 300 - DN 225 S1
R11.109.315250
250
315
164
33
12
DN 350 - DN 300 S1
R11.109.355315
315
355
184
20
12
DN 375 - DN 350 S1
R11.109.400355
355
400
206
22
12
DN 400 - DN 375 S1
R11.109.450400
400
450
231
25
12
DN 450 - DN 400 S1
R11.109.500450
450
500
256
25
12
DN 500 - DN 450 S1
R11.109.560500
500
560
270
14
12
DN 575 - DN 500 S1
R11.109.630560
560
630
285
15
12
DN 650 - DN 575 S1
R11.109.710630
630
710
305
20
9
DN 750 - DN 650 S2/S1
R11.109.826710
710
826
330
20
9
COMPLIES WITH AS/NZS3518:2004
44
CODE
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
FAUCET SOCKET (PLAIN THREADED SOCKET)
SIZE
SIZE
SIZE
SW SOCKET
THREAD
SPIGOT
DN 15 S1
1/2” BSP
DN 20 S1
DN 20 S1
3/4” BSP
DN 25 S1
1”
A
B
C
ID
L
OD
Z
PN
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
RATING
R01.101.015
32
41
18
21
20
27
19
15
DN 25 S1
R01.101.020
38
47
21
27
22
34
22
15
DN 32 S1
R01.101.025
47
54
24
34
25
42
25
15
DN 32 S1
1 1/4” BSP
-
R01.101.032
57
61
28
42
29
-
-
15
DN 40 S1
1 1/2” BSP
DN 50 S1
R01.101.040
65
66
28
48
31
60
29
15
DN 50 S1
2”
-
R01.101.050
80
73
31
60
37
-
-
15
BSP
BSP
CODE
COMPLIES WITH AS3518:2004
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
45
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
VALVE ADAPTOR (PLAIN THREADED NIPPLE)
SIZE
SIZE
SIZE
SW SPIGOT
THREAD
SW
SOCKET
DN 15 S1
1/2”
-
DN 20 S1
3/4”
DN 25 S1
1”
DN 32 S1
CODE
A
B
C
ID
OD
Z1
Z
PN
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
RATING
R01.107.015
27
41
15
-
21
-
21
15
DN 15 S1
R01.107.020
36
46
17
21
27
26
24
15
DN 20 S1
R01.107.025
43
51
19
27
34
29
26
15
1 1/4”
DN 25 S1
R01.107.032
52
59
22
34
42
34
30
15
DN 40 S1
1 1/2”
-
R01.107.040
59
62
22
-
48
-
31
15
DN 50 S1
2”
DN 40 S1
R01.107.050
74
73
26
48
60
36
36
15
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
REDUCING VALVE ADAPTOR (REDUCING PLAIN THREADED NIPPLE)
SIZE
SIZE
SIZE
SW SPIGOT
THREAD
SW
SOCKET
DN 20 S1
1/2”
DN 15 S1
DN 25 S1
1/2”
DN 20 S1
DN 25 S1
3/4”
DN 32 S1
A
B
C
ID
OD
Z1
Z
PN
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
RATING
R01.107.020015
27
43
15
21
27
19
21
15
R01.107.025015
27
47
15
27
34
25
22
15
DN 20 S1
R01.107.025020
36
49
17
27
34
27
24
15
1”
DN 25 S1
R01.107.032025
43
55
19
34
42
30
26
15
DN 40 S1
1”
-
R01.107.040025
43
58
19
-
48
-
27
15
DN 40 S1
1 1/4”
-
R01.107.040032
52
61
22
-
48
-
30
15
DN 50 S1
1”
DN 25 S1
R01.107.050025
43
64
19
48
60
33
27
15
DN 50 S1
1 1/2”
DN 40 S1
R01.107.050040
59
68
22
48
60
27
31
15
COMPLIES WITH AS3518:2004
46
CODE
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
VALVE SOCKET (MALE ADAPTOR)
SIZE
SIZE
SW SOCKET
THREAD
CODE
A
B
C
ID
Z
PN
(mm)
(mm)
(mm)
(mm)
(mm)
RATING
DN 15 S1
1/2” BSP
R01.151.015
27
38
15
21
18
15
DN 20 S1
3/4” BSP
R01.151.020
34
42
17
27
20
15
DN 25 S1
1”
R01.151.025
43
49
19
34
24
15
BSP
DN 32 S1
1 1/4” BSP
R01.151.032
52
56
22
42
27
15
DN 40 S1
1 1/2” BSP
R01.151.040
59
58
22
48
27
15
DN 50 S1
2”
BSP
R01.151.050
74
70
26
60
33
15
DN 80 S1
3”
BSP
R01.151.080
107
95
31
89
46
12
DN 100 S1
4”
BSP
R01.151.100
129
110
39
114
55
12
COMPLIES WITH AS3518:2004
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
47
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
FAUCET ADAPTOR (FEMALE ADAPTOR)
SIZE
SIZE
SIZE
SW SPIGOT
THREAD
SW SOCKET
DN 15 S1
1/2” BSP
-
DN 20 S1
3/4” BSP
DN 25 S1
1”
BSP
DN 32 S1
1 1/4” BSP
DN 40 S1
1 1/2” BSP
DN 50 S1
2”
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
COMPLIES WITH AS3518:2004
48
BSP
CODE
A
B
C
ID
OD
Z
Z1
PN
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
RATING
R01.153.015
32
42
18
-
21
22
-
15
DN 15 S1
R01.153.020
38
47
21
21
27
25
27
15
DN 20 S1
R01.153.025
47
53
24
27
34
28
31
15
DN 25 S1
R01.153.032
57
63
28
34
42
34
38
15
-
R01.153.040
65
65
28
-
48
34
-
15
DN 40 S1
R01.153.050
80
76
31
48
60
39
43
15
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
FABRICATED
MOULDED
CAP
SIZE
DN 15 S1
CODE
R01.140.015
ID
A
B
C
(mm)
(mm)
(mm)
(mm)
21
27
9
29
TYPE
PN
RATING
M
15
DN 20 S1
R01.140.020
27
33
11
33
M
15
DN 25 S1
R01.140.025
34
41
14
39
M
15
DN 32 S1
R01.140.032
42
52
17
46
M
15
DN 40 S1
R01.140.040
48
59
20
51
M
15
DN 50 S1
R01.140.050
60
74
24
61
M
15
DN 65 S1
R01.140.065
75
106
35
79
F*
12
DN 80 S1
R01.140.080
89
106
28
79
M
12
DN 100 S1
R01.140.100
114
132
33
95
M
12
DN 125 S1
R01.140.125
140
192
61
130
F*
12
DN 150 S1
R01.140.150
168
192
42
130
M
12
DN 200 S1
R11.140.225
225
262
30
150
F
9
DN 225 S1
R11.140.250
250
280
35
166
F
9
DN 300 S1
R11.140.315
315
355
35
199
F
9
* CAP DN65 IS MANUFACTURED FROM CAP DN80 AND DN80-DN65 REDUCING BUSH
* CAP DN125 IS MANUFACTURED FROM CAP DN150 AND DN150-DN125 REDUCING BUSH
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
49
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
THREADED PLUG
SIZE
SIZE
CODE
THREAD
DN 15 S1
1/2” BSP
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
B
C
PN
(mm)
(mm)
RATING
27
21
15
15
DN 20 S1
3/4” BSP
R01.155.020
33
23
16
15
DN 25 S1
1”
BSP
R01.155.025
41
26
19
15
DN 32 S1
1 1/4” BSP
R01.155.032
51
30
22
15
DN 40 S1
1 1/2” BSP
R01.155.040
58
31
22
15
DN 50 S1
2”
R01.155.050
71
36
26
15
COMPLIES WITH AS3518:2004
50
R01.155.015
A
(mm)
BSP
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
SOCKET UNION
SIZE
DN 15 S1
CODE
R01.205.015K
A
B
ID
Z
PN
(mm)
(mm)
(mm)
(mm)
RATING
35
43
21
10
15
DN 20 S1
R01.205.020K
43
47
27
12
15
DN 25 S1
R01.205.025K
60
59
34
12
15
DN 32 S1
R01.205.032K
74
70
42
12
15
DN 40 S1
R01.205.040K
83
73
48
12
15
DN 50 S1
R01.205.050K
103
86
60
12
15
DN 65 S1
R01.205.065H
-
-
-
-
-
DN 80 S1
R01.205.080K
158
114
89
12
15
DN 100 S1
R01.205.100K
182
142
114
14
15
SEALS’ MATERIAL - EPDM
COMPLIES WITH AS3518:2004
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
51
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
SADDLE CLIP
SIZE
DN 15 S1
A
B
C
D
t
(mm)
(mm)
(mm)
(mm)
(mm)
21
13
37
14
27
3
DN 20 S1
R05.455.020
27
18
41
14
34
3
R05.455.025
34
21
45
16
42
4
DN 32 S1
R05.455.032
42
29
65
16
54
4
DN 40 S1
R05.455.040
48
34
67
16
61
5
DN 50 S1
R05.455.050
60
38
87
22
73
5
DN 80 S1
R05.455.080
89
50
122
34
99
5
DN 100 S1
R05.455.100
114
65
156
38
127
5
MATERIAL : BLACK POLYPROPYLENE
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
R05.455.015
ID
(mm)
DN 25 S1
C = CLIP THICKNESS
52
CODE
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
PIPE CLIP
SIZE
CODE
B
C
D
d1
d2
d3
Z1
Z2
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
TYPE
DN 15 S1
R05.434.015
25.5
10
6
21
10.5
5.5
16.5
19
B
DN 20 S1
R05.434.020
28.5
10
6
27
10.5
5.5
19
21.5
B
DN 25 S1
R05.434.025
32
10
6
34
10.5
5.5
24
26.5
B
DN 32 S1
R05.434.032
36
10
6.5
42
14
6.5
33.5
33.5
C
DN 40 S1
R05.434.040
39
10
6.5
48
14
6.5
37
37
C
DN 50 S1
R05.434.050
50
10
10
60
17
8.5
44.5
44.5
C
DN 80 S1
R05.434.080
105
-
15
89
-
9
89
71
C
DN 100 S1
R05.434.100
120
-
15
114
-
9
99
81
C
DN 150 S1
R05.434.150
147
-
20
169
-
11
136
111
G
MATERIAL: BLACK POLYPROPYLENE
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
53
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
RUBBER EXPANSION JOINT
SIZE
CODE
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
C
(mm)
95
8
D
E
PN
(mm)
RATING
15°
4
15
DN 32 S1
R04.452.032
DN 40 S1
R04.452.040
95
8
15°
4
15
DN 50 S1
R04.452.050
105
8
15°
5
15
DN 80 S1
R04.452.080
130
12
15°
6
15
DN 100 S1
R04.452.100
135
18
15°
10
15
DN 150 S1
R04.452.150
180
18
15°
10
15
DN 200 S1
R14.452.225
205
25
15°
14
15
DN 225 S1
R14.452.250
240
25
15°
14
15
DN 300 S1
R14.452.315
260
25
15°
14
15
DN 350 S1
R14.452.355
265
25
15°
14
9
DN 375 S1
R14.452.400
265
25
15°
14
9
DN 400 S1
R14.452.450
265
25
15°
14
9
DN 450 S1
R14.452.500
265
25
15°
14
9
DN 500 S1
R14.452.560
254
25
15°
16
9
DN 575 S1
R14.452.630
254
25
15°
16
6
DN 650 S1
R14.452.710
254
25
10°
16
6
* flanges supplied are zinc plated. Galvanised available on request.
54
A
(mm)
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
ANCHOR SLEEVE
SIZE
CODE
ID
A
B
(mm)
(mm)
(mm)
74
40
DN 50 S1
R01.272.050
60
DN 65 S1
R01.272.065
76
89
40
DN 80 S1
R01.272.080
89
104
50
DN 100 S1
R01.272.100
115
140
60
DN 125 S1
R01.272.125
141
168
75
DN 150 S1
R01.272.150
169
208
90
DN 200 S1
R11.272.225
227
250
120
DN 225 S1
R11.272.250
251
275
120
DN 300 S1
R11.272.315
316
344
120
DN 350 S1
R11.272.355
356
390
120
DN 375 S1
R11.272.400
401
450
120
DN 400 S1
R11.272.450
451
500
120
DN 450 S1
R11.272.500
502
550
180
DN 500 S1
R11.272.560
562
616
180
DN 575 S1
R11.272.630
632
710
180
DN 650 S1
R11.272.710
712
826
200
DN 750 S1
R11.272.826
828
922
200
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
55
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
ANCHOR FLANGE
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
SIZE
56
CODE
ID
A
B
C
D
(mm)
(mm)
(mm)
(mm)
(mm)
74
DN 50 S1
R01.137.050
61
96
40
14
DN 65 S1
R01.137.065
76
106
47
10
90
DN 80 S1
R01.137.080
90
127
57
18
118
DN 100 S1
R01.137.100
115
159
70
20
134
DN 125 S1
R01.137.125
141
187
84
14
165
DN 150 S1
R01.137.150
169
214
100
24
192
DN 200 S1
R11.137.225
226
271
144
35
247
DN 225 S1
R11.137.250
251
334
191
70
305
DN 300 S1
R11.137.315
317
376
224
70
362
DN 350 S1
R11.137.355
357
440
244
70
415
DN 375 S1
R11.137.400
402
488
306
110
450
DN 400 S1
R11.137.450
452
548
331
110
506
DN 450 S1
R11.137.500
502
613
356
110
561
DN 500 S1
R11.137.560
562
665
282
50
615
DN 575 S1
R11.137.630
632
708
340
65
669
DN 650 S1
R11.137.710
715
808
325
70
770
DN 750 S2
R11.137.826
804
922
430
110
870
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
BALL CHECK VALVE SINGLE UNION
SIZE
CODE
A
B
Z
PN
(mm)
(mm)
(mm)
RATING
DN 15 S1
R01.***.015K
48
95
62
15
DN 20 S1
R01.***.020K
59
112
73
15
DN 25 S1
R01.***.025K
69
124
79
15
DN 32 S1
R01.***.032K
96
148
94
15
DN 40 S1
R01.***.040K
96
148
88
15
DN 50 S1
R01.***.050K
103
177
105
15
DN 80 S1
R01.***.080K
178
215
114
9
CODE 836 - EPDM SEALS
CODE 838 - FPM SEALS
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
57
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
BALL VALVE DOUBLE UNION
SIZE
B
C
D
Z
PN
(mm)
(mm)
(mm)
(mm)
RATING
R01.***.015K
51
101
48
81
67
15
DN 20 S1
R01.***.020K
63
119
65
87
79
15
DN 25 S1
R01.***.025K
73
134
69
101
86
15
DN 32 S1
R01.***.032K
105
161
88
127
101
15
DN 40 S1
R01.***.040K
105
160
88
127
98
15
DN 50 S1
R01.***.050K
135
191
108
151
118
15
DN 80 S1
R01.***.080K
182
260
138
191
158
15
DN 100 S1
R01.***.100K
217
314
165
241
187
15
CODE 882 - FPM SEALS
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
A
(mm)
DN 15 S1
CODE 880 - EPDM SEALS
58
CODE
EURAPIPE ABS PIPE & FITTINGS PRODUCT CATALOGUE
®
ABS SOLVENT CEMENT
MEK CLEANER/PRIMER
CAN SIZE
CODE
(litres)
CAN SIZE
CODE
(litres)
0.25
R01.461.025A
0.25
R01.463.025A
1
R01.461.100A
1
R01.463.100A
R01.461.400A
4
R01.463.400A
4
SOLVENT CEMENT USAGE*
SIZE
SOLVENT WELD
JOINTS PER LITRE**
DN 50 S1
135
DN 80 S1
45
DN 100 S1
35
DN 125 S1
20
DN 150 S1
20
DN 200 S1
10
DN 225 S1
4
DN 300 S1
4
DN 350 S1
3
DN 375 S1
2
DN 400 S1
1
1
DN 500 S1
0.5
DN 575 S1
0.5
DN 650 S1
0.3
DN 750 S1
0.3
EURAPIPE® ABS PIPE & FITTINGS PRODUCT CATALOGUE
DN 450 S1
* The usage of MEK is approximately 50% that of ABS cement
** A socket counts as 2 joints, a tee as 3 joints etc.
59
ADELAIDE
P: 08 8340 3411
F: 08 8340 3422
E: [email protected]
BRISBANE
P: 07 3266 2255
F: 07 3260 5221
E: [email protected]
DARWIN
P: 08 8935 3300
F: 08 8947 3981
E: [email protected]
Gold Coast
P: 07 5589 4400
F: 07 5534 7079
E: [email protected]
Melbourne
P: 03 9309 9133
F: 03 9309 6237
E: [email protected]
Newcastle
P: 02 4914 0700
F: 02 4966 8776
E: [email protected]
Perth
P: 08 9346 8500
F: 08 9346 8501
E: [email protected]
Sydney
P: 02 9794 3440
F: 02 9794 3499
E: [email protected]
Townsville
P: 07 4725 5940
F: 07 4725 4995
E: [email protected]
AUCKLAND
P: +64 9 921 7230
F: +64 9 921 7231
E: [email protected]
HAMILTON
P: +64 7 958 7140
F: +64 7 958 7141
E: [email protected]
WELLINGTON
P: +64 4 913 8514
F: +64 4 913 8511
E: [email protected]
CHRISTCHURCH
P: +64 3 968 3260
F: +64 3 968 3261
E: [email protected]
PENTAIR WATER SOLUTIONS
LEVEL 3, 9 GEORGE ST PARRAMATTA, NEW SOUTH WALES 2150 / WWW.PENTAIR.COM/WATERSOLUTIONS
All Pentair trademarks and logos are owned by Pentair Ltd. All other brand or product names are trademarks or registered marks of their respective owners.
Because we are continuously improving our products and services, Pentair reserves the right to change specifications without prior notice.
ABSPC1405 © 2014 Pentair Ltd. All Rights Reserved.

Oilfield Screens - Setting the Bar in Solids Control

0301 KSS Nylon Cable Tie