HINGES CONTENTS This section contains standard size and wide throw hinges. The Sun Valley Bronze lift-off ball bearing adjustable hinge is a unique patented design. It is vertically adjustable for wear and equal load bearing. Sand cast in the same alloy as all Sun Valley Bronze hardware the ball bearing hinge is available in all of our standard finishes. All Sun Valley Bronze hinges are made in-house. There may be slight variations due to the sand-casting process. TABLE OF CONTENTS: Door Hinge Finials Page 21-2 Standard Hinges Pages 21-3 – 21-6 Wide Throw Hinges Pages 21-7 – 21-9 Extruded Hinges Pages 21-10 – 21-11 Hinge Cozy Page 21-12 Pivot Hinges Page 21-13 Bi-Fold Door Hinges Page 21-14 Active Strap Hinges Pages 21-15 – 21-20 Active Surface Mount Strap Hinges Pages 21-21 Dummy Strap Hinges Pages 21-22 – 21-33 Cabinet Hinge Finials Page 21-34 Cabinet Hinges Page 21-35 Cabinet Strap Hinges Page 21-36 ORDERING INSTRUCTIONS: Hinges: See Ordering Instructions in Binder 1/ Dealer Information. Custom Hinges: See Custom Ordering Instructions in Binder 1/ Dealer Information. INSIDE INSIDE DOOR HANDING GUIDE: Left Hand (LH) OUTSIDE Right Hand (RH) Left Hand Reverse (LHR) OUTSIDE Right Hand Reverse (RHR) PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited. Revised 12/01/14 Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w . s u n v a l l e y b r o n z e . c o m 21-1 DOOR HINGE FINIALS BHF-BALL Ball finial. BHF-BUTN Button finial. 1/8" 1 1/2" 1/2" 5/8" 5/8" 5/8" BHF-ACRN Acorn finial. 1/4" 3/4" 1 1/8" Illustrations are for demonstration purposes only. 5/8" 5/8" 5/8" BHF-FDL Fleur de Lis finial. BHF-FLAT Flat finial. 1" 7/8" 1 5/8" BHF-DOME Dome finial. 5/8" 5/8" 5/8" BHF-RDG Ridge finial. BHF-STPL Steeple finial 1 3/4" BHF-FREN French finial. 5/8" BHF-URN Urn finial. PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited. Revised 12/01/14 Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w . s u n v a l l e y b r o n z e . c o m 21-2 3000 SERIES STANDARD DOOR HINGES Illustrations are for demonstration purposes only. 3 1/2" 3" .675" .30" .35" .55" .35" 5/8" 1.75" 1.5" 3" 3 1/2" .30" 5/8" BH-3535 – 3 1/2" x 3 1/2" hinge. – Shown w/flat finial. – Leaf thickness .160. BH-3030 – 3" x 3" hinge. – Shown w/flat finial. – Leaf thickness .155. Standard door hinges. BH-3030 3” x 3” Standard door hinge w/ finial. BH-3535 3 1/2” x 3 1/2” Standard door hinge w/ finial. Door handing is required. Finial style must be specified. Custom sizes are available. Please call for engineering specifications if needed. Additional hinge screws BH-SCREWS-REG 1 1/2” BH-SCREWS-LG 2 1/2” Non-removeable pin. NRP each Re-size any standard hinge. Custom hinge machining per hinge PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited. Revised 12/01/14 Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w . s u n v a l l e y b r o n z e . c o m 21-3 4000 SERIES STANDARD DOOR HINGES Illustrations are for demonstration purposes only. 4" 4 1/2" 1" .5" .5" .75" .375" 1.625" 1.50" 4" 4 1/2" .375" 5/8" 5/8" BH-4040 – 4" x 4" hinge. – Shown w/flat finial. – Leaf thickness .165. BH-4545 – 4 1/2" x 4 1/2" hinge. – Shown w/flat finial. – Leaf thickness .210. Standard door hinges. BH-4030 4” x 3” Door hinge w/ finial. Custom hinge machining fee applies.* (Not shown) BH-4035 4” x 3 1/2” Door hinge w/ finial. Custom hinge machining fee applies.* (Not shown) BH-4040 4” x 4” Standard door hinge w/ finial. BH-4535 4 1/2” x 3 1/2” Door hinge w/ finial. Custom hinge machining fee applies.* (Not shown) BH-4540 4 1/2” x 4” Door hinge w/ finial. (Not shown) BH-4545 4 1/2” x 4 1/2” Standard door hinge w/ finial. Door handing is required. Finial style must be specified. Custom sizes are available. Please call for engineering specifications if needed. Additional hinge screws BH-SCREWS-REG 1 1/2” BH-SCREWS-LG 2 1/2” Non-removeable pin. NRP each Re-size any standard hinge. *Custom hinge machining per hinge PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited. Revised 12/01/14 Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w . s u n v a l l e y b r o n z e . c o m 21-4 5000 SERIES STANDARD DOOR HINGES Illustrations are for demonstration purposes only. 5 1/2" 1" 1" .5" 5" .5" 3 1/2" .375" 5/8" 5/8" BH-5035 – 5" x 3 1/2" hinge. – Shown w/flat finial. – Leaf thickness .210. BH-5050 – 5" x 5" hinge. – Shown w/flat finial. – Leaf thickness .210. 2" 1.75" 5" 5" 5 1/2" .375" 5/8" BH-5555 – 5 1/2" x 5 1/2" hinge. – Shown w/flat finial. – Leaf thickness .210. Standard door hinges. BH-5035 5” x 3 1/2” Door hinge w/ finial. Custom hinge machining fee applies.* BH-5040 5” x 4” Door hinge w/ finial. Custom hinge machining fee applies.* (Not shown) BH-5050 5” x 5” Standard door hinge w/ finial. BH-5555 5 1/2” x 5 1/2” Standard door hinge w/ finial. Door handing is required. Finial style must be specified. Custom sizes are available. Please call for engineering specifications if needed. Additional hinge screws BH-SCREWS-REG 1 1/2” BH-SCREWS-LG 2 1/2” Non-removeable pin. NRP each Re-size any standard hinge. *Custom hinge machining per hinge PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited. Revised 12/01/14 Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w . s u n v a l l e y b r o n z e . c o m 21-5 6000 SERIES STANDARD DOOR HINGES Illustrations are for demonstration purposes only. 4 1/2" 1" 6" .5" 4" .95" 6" 1.75" 6" 6" .375" 5/8" 5/8" BH-6040 – 6" x 4" hinge. – Shown w/flat finial. – Leaf thickness .210. BH-6045 – 6" x 4 1/2" hinge. – Shown w/flat finial. – Leaf thickness .210. 5/8" BH-6060 – 6" x 6" hinge. – Shown w/flat finial. – Leaf thickness .210. Standard door hinges. BH-6040 6” x 4” Door hinge w/ finial. BH-6045 6” x 4 1/2” Door hinge w/ finial. BH-6050 6” x 5” Door hinge w/ finial. Custom hinge machining fee applies.* (Not shown) BH-6055 6” x 5 1/2” Door hinge w/ finial. Custom hinge machining fee applies.* (Not shown) BH-6060 6” x 6” Standard door hinge w/ finial. Door handing is required. Finial style must be specified. Custom sizes are available. Please call for engineering specifications if needed. Additional hinge screws BH-SCREWS-REG 1 1/2” BH-SCREWS-LG 2 1/2” Non-removeable pin. NRP each Re-size any standard hinge. *Custom hinge machining per hinge PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited. Revised 12/01/14 Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w . s u n v a l l e y b r o n z e . c o m 21-6 3000 SERIES WIDE THROW DOOR HINGES Illustrations are for demonstration purposes only. 3 1/2" 4" 5/8" BH-3540 – 3 1/2" x 4" wide throw hinge. – Shown w/flat finial. – Leaf thickness .160. Wide throw door hinges. BH-3540 3 1/2” x 4” Wide throw door hinge w/ finial. Door handing is required. Finial style must be specified. Custom sizes are available. Please call for engineering specifications if needed. Additional hinge screws BH-SCREWS-REG 1 1/2” BH-SCREWS-LG 2 1/2” Non-removeable pin. NRP each Re-size any standard hinge. Custom hinge machining per hinge PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited. Revised 12/01/14 Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w . s u n v a l l e y b r o n z e . c o m 21-7 4000 SERIES WIDE THROW DOOR HINGES Illustrations are for demonstration purposes only. 5 1/2" 4" 4 1/2" 5" 5/8" 5/8" BH-4050 – 4" x 5" wide throw hinge. – Shown w/flat finial. – Leaf thickness .165. BH-4555 – 4 1/2" x 5 1/2" wide throw hinge. – Shown w/flat finial. – Leaf thickness .210. Wide throw door hinges. BH-4045 4” x 4 1/2” Wide throw door hinge w/ finial. Custom hinge machining fee applies.* (Not shown) BH-4050 4” x 5” Wide throw door hinge w/ finial. BH-4550 4 1/2” x 5” Wide throw door hinge w/ finial. (Not shown) BH-4555 4 1/2” x 5 1/2” Wide throw door hinge w/ finial. BH-4560 4 1/2” x 6” Wide throw door hinge w/ finial. Custom hinge machining fee applies.* (Not shown) BH-4570 4 1/2” x 7” Wide throw door hinge w/ finial. (Not shown) Door handing is required. Finial style must be specified. Custom sizes are available. Please call for engineering specifications if needed. Additional hinge screws BH-SCREWS-REG 1 1/2” BH-SCREWS-LG 2 1/2” Non-removeable pin. NRP each Re-size any standard hinge. *Custom hinge machining per hinge PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited. Revised 12/01/14 Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w . s u n v a l l e y b r o n z e . c o m 21-8 5000 SERIES WIDE THROW DOOR HINGES Illustrations are for demonstration purposes only. 5" 6" 5/8" BH-5060 – 5" x 6" wide throw hinge. – Shown w/flat finial. – Leaf thickness .210. Wide throw door hinges. BH-5060 5” x 6” Wide throw door hinge w/ finial. Door handing is required. Finial style must be specified. Custom sizes are available. Please call for engineering specifications if needed. Additional hinge screws BH-SCREWS-REG 1 1/2” BH-SCREWS-LG 2 1/2” Non-removeable pin. NRP each Re-size any standard hinge. Custom hinge machining per hinge PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited. Revised 12/01/14 Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w . s u n v a l l e y b r o n z e . c o m 21-9 4000 SERIES EXTRUDED DOOR HINGES Illustrations are for demonstration purposes only. 4 1/2" 4" 4 1/2" 4" 5/8" 5/8" BHE-4040-2K – 4" x 4" solid bronze hinge. – Shown w/flat finial. – Leaf thickness .130. BHE-4545-2K – 4 1/2" x 4 1/2" solid bronze hinge. – Shown w/flat finial. – Leaf thickness .135. Extruded door hinges. BHE-4040-2K 4” x 4” Solid bronze extruded door hinge w/ finial. BHE-B4040-2K 4” x 4” Solid bronze extruded door hinge w/ finial. Standard ball bearing & adjustability. (Not shown) BHE-4545-2K 4 1/2” x 4 1/2” Solid bronze extruded door hinge w/ finial. BHE-B4545-2K 4 1/2” x 4 1/2” Solid bronze extruded door hinge w/ finial. Standard ball bearing & adjustability. (Not shown) Door handing is required. Finial style must be specified. Additional hinge screws. BH-SCREWS-REG 1 1/2” BH-SCREWS-LG 2 1/2” Non-removeable pin. NRP each PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited. Revised 12/01/14 Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w . s u n v a l l e y b r o n z e . c o m 21-10 4000 SERIES EXTRUDED DOOR HINGES Illustrations are for demonstration purposes only. 4 1/2" 4" 4 1/2" 4" 5/8" 5/8" BHE-4040-3K – 4" x 4" solid bronze hinge. – Shown w/flat finial. – Leaf thickness .130. BHE-4545-3K – 4 1/2" x 4 1/2" solid bronze hinge. – Shown w/flat finial. – Leaf thickness .135. Extruded door hinges. BHE-4040-3K 4” x 4” Solid bronze extruded door hinge w/ finial. BHE-4545-3K 4 1/2” x 4 1/2” Solid bronze extruded door hinge w/ finial. Door handing is required. Finial style must be specified. Additional hinge screws. BH-SCREWS-REG 1 1/2” BH-SCREWS-LG 2 1/2” Non-removeable pin. NRP each PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited. Revised 12/01/14 Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w . s u n v a l l e y b r o n z e . c o m 21-11 HINGE COZY Illustrations are for demonstration purposes only. 2" 5/8" BH-COZY-1 – Hinge cozy. – Shown w/Button finial. Hinge cozy. BH-COZY-1 Hinge cozy w/ finial. Hinge size is required. Finial style must be specified. Custom sizes are available. PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited. Revised 12/01/14 Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w . s u n v a l l e y b r o n z e . c o m 21-12 PIVOT HINGES Illustrations are for demonstration purposes only. 3 7/8" 1" PH-100 – Pivot hinge. 1/4" 2 3/4" 1 7/16" 3 7/8" 5/8" Tapers to 3/4" at base. Pivot hinges. PH-100 Pivot hinge. Additional hinge screws. BH-SCREWS-REG 1 1/2” BH-SCREWS-LG 2 1/2” PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited. Revised 12/01/14 Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w . s u n v a l l e y b r o n z e . c o m 21-13 BI-FOLD DOOR HINGES Illustrations are for demonstration purposes only. 4 1/2" 5/8" 4" 1 3/4" 5/8" BH-4040BFP – Bi-fold door hinge. – Shown w/ball finial. Bi-fold door hinges. BH-4040BFP 4” x 4 1/2” Bi-fold door hinge w/finial. Door handing is required. Finial style must be specified. Custom sizes are available. Additional hinge screws. BH-SCREWS-REG 1 1/2” BH-SCREWS-LG 2 1/2” PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited. Revised 12/01/14 Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w . s u n v a l l e y b r o n z e . c o m 21-14 BEAN ACTIVE STRAP HINGES Illustrations are for demonstration purposes only. 1 1/8" 1 1/4" 1 3/8" 6 1/8" 1 3/16" 7 5/8" 1 1/2" 2 5/8" 4" 3 3/16" 1 3/8" 2 11/16" 7 5/8" 1 1/8" 23" 18 1/8" 4" 1 1/4" 6 1/8" SH-B15ACT – 15" Active strap hinge (left). – Shown w/button finial. – 2" Heel. 3 3/16" 5 1/4" 5 1/4" 4" 3 1/8" 2" 1 3/8" 1 15/16" 4" 1 1/4" SH-B13ACT – 13 1/4" Active strap hinge (left). – Shown w/button finial. – 1 15/16" Heel. 3 1/16" 15" 13 1/4" 1 1/4" 10 1/16" 10 1/16" 1 3/16" SH-B23ACT – 23" Active strap hinge (left). – Shown w/button finial. – 2 5/8" Heel. SH-B18ACT – 18 1/8" Active strap hinge (left). – Shown w/button finial. – 2 11/16" Heel. 1 1/4" 10" 10" 10" 3 11/16" 4" 3" 1 3/4" 33 1/8" 1 3/8" SH-B33ACT – 33 1/8" Active strap hinge (left). – Shown w/button finial. – 3" Heel. Bean active strap hinges. SH-B13ACT 13 1/4” Bean active strap hinge. SH-B15ACT 15” Bean active strap hinge. SH-B18ACT 18 1/8” Bean active strap hinge. SH-B23ACT 23” Bean active strap hinge. SH-B33ACT 33 1/8” Bean active strap hinge. SH-B33ACT-45 33 1/8” Bean active strap hinge w/4 1/2” hinge leaf. (Not shown) ** Specify if active strap hinges are surface mount or mortise mount.** Door handing is required. Finial style must be specified. Custom sizes are available. Provided with 5/16” x 1 1/2” lags. Additional hinge screws. BH-SCREWS-REG 1 1/2” BH-SCREWS-LG 2 1/2” LAG-2 1” x 1/2” Square 1/2" LAG-1 15/16” x 1/2” Dome 1/2" Additional lag bolt covers. LAG-3 7/8” x 1/2” Cylindrical 1" 1/2" 1 5/16" 7/8" PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited. Revised 12/01/14 Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w . s u n v a l l e y b r o n z e . c o m 21-15 BEAN ACTIVE STRAP HINGES Illustrations are for demonstration purposes only. 4 1/4" 2 7/16" 29 3/4" 8 15/16" 8 15/16" 8 15/16" 1 3/16" 1" 1 1/4" SH-130ACT – 29 3/4" Active strap hinge. – Left shown. Active Strap hinges. SH-130ACT 29 3/4” Bean active strap hinge. Door handing is required. Custom sizes are available. Provided with 5/16” x 1 1/2” lags. Attaches to jamb/post with 3/8” - 16 x 2” hanger bolt. LAG-1 15/16” x 1/2” Dome 1/2" Additional lag bolt covers. LAG-2 1” x 1/2” Square 1/2" 1 5/16" LAG-3 7/8” x 1/2” Cylindrical 1/2" 1" 7/8" PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited. Revised 12/01/14 Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w . s u n v a l l e y b r o n z e . c o m 21-16 FLEUR DE LIS ACTIVE STRAP HINGES 3 9/16" Illustrations are for demonstration purposes only. 1 1/4" 6" 6" 1 1/4" 4 1/2" 4 3/4" 1 7/8" 7 7/8" 7 7/8" INTERIOR INTERIOR EXTERIOR EXTERIOR SH-FDL-18-ACT – 18" Fleur de Lis active strap hinge (left). – Shown with flat finial. – 3 1/2" Heel. 7 7/8" 4 3/4" SH-FDL-30-ACT – 30" Fleur de Lis active strap hinge (left). – Shown with flat finial. – 3 9/16" Heel. 4 3/4" 1 7/8" 3 5/8" 32 1/8" 4" 1 1/4" 30" 4" 4" 4 3/4" 1 7/8" 3 1/2" 18 1/8" 8 9/16" 8 9/16" 8 9/16" 4 3/4" INTERIOR EXTERIOR SH-FDL-32-ACT – 32 1/8" Fleur de Lis active strap hinge (left). – Shown with flat finial. – 3 5/8" Heel. Fleur de Lis active strap hinges. SH-FDL18ACT 18 1/8” Fleur de Lis active strap hinge. SH-FDL30ACT 30” Active Fleur de Lis active strap hinge. SH-FDL32ACT 32 1/8” Fleur de Lis active strap hinge. ** Specify if active strap hinges are surface mount or mortise mount.** Door handing is required. Finial style must be specified. Custom sizes are available. Provided with 5/16” x 1 1/2” lags. Additional hinge screws. BH-SCREWS-REG 1 1/2” BH-SCREWS-LG 2 1/2” 15/16” x 1/2” Dome LAG-2 1/2" LAG-1 1” x 1/2” Square 1/2" Additional lag bolt covers. LAG-3 7/8” x 1/2” Cylindrical 1" 1/2" 1 5/16" 7/8" PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited. Revised 12/01/14 Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w . s u n v a l l e y b r o n z e . c o m 21-17 ARCH ACTIVE STRAP HINGES Illustrations are for demonstration purposes only. 1" 2 5/8" 3 1/2" 9" 9/16" 3 1/2" 1 3/8" 3/4" 1" 8 3/4" 8 3/4" 1 3/8" 1" 9" 4" 1" 3 1/2" 9/16" 1" 20 3/16" 3/4" 3 1/2" 6 3/8" 2 5/8" 1" 1 3/4" 1 1/2" 1 1/2" SH-ARCH6-ACT – 6 3/8" Active strap hinge. – Left shown. SH-ARCH20-ACT – 20 3/16" Active strap hinge. – Left shown. Arch active strap hinges. SH-ARCH6-ACT 6 3/8” Arch active strap hinge. SH-ARCH20-ACT 20 3/16” Arch active strap hinge. Door handing is required. Custom sizes are available. Provided with 5/16” x 1 1/2” lags. PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited. Revised 12/01/14 Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w . s u n v a l l e y b r o n z e . c o m 21-18 ACTIVE STRAP HINGES Illustrations are for demonstration purposes only. 1 1/4" 2 1/2" 16 3/8" 6 3/16" 6 3/16" 2" 1" 1 1/4" SH-160ACT – 16 1/2" Active strap hinge. – Left shown. Active strap hinges. SH-160ACT 16 3/8” Active strap hinge. Door handing is required. Custom sizes are available. Provided with 5/16” x 1 1/2” lags. Attaches to jamb/post with 5/16” - 18 x 2” hanger bolt. LAG-1 15/16” x 1/2” Dome 1/2" Additional lag bolt covers. LAG-2 1” x 1/2” Square 1/2" 1 5/16" LAG-3 7/8” x 1/2” Cylindrical 1/2" 1" 7/8" PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited. Revised 12/01/14 Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w . s u n v a l l e y b r o n z e . c o m 21-19 ACTIVE STRAP HINGES Illustrations are for demonstration purposes only. 4" 2 1/2" 16 5/8" 5/8" 1 1/4" 6 7/8" 6 7/8" 1 1/4" SH-F16ACT – 16 5/8" Active strap hinge. – Left shown. – Shown w/flat finial. Active strap hinges. SH-F16ACT 16 5/8” Active strap hinge. Door handing is required. Custom sizes are available. Specify finial. Provided with 5/16” x 1 1/2” lags. LAG-1 15/16” x 1/2” Dome 1/2" Additional lag bolt covers. LAG-2 1” x 1/2” Square 1/2" 1 5/16" LAG-3 7/8” x 1/2” Cylindrical 1/2" 1" 7/8" PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited. Revised 12/01/14 Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w . s u n v a l l e y b r o n z e . c o m 21-20 ACTIVE SURFACE MOUNT STRAP HINGES Illustrations are for demonstration purposes only. 1 1/4" 8 9/16" 2 3/4" 1" 8 9/16" 1" 9 11/16" 1 1/4" 9 11/16" 9 11/16" 1" SH-T-SM32 – 31 15/16" Active strap hinge. – 5/16" Thick hinge leaf. – Left shown. SH-T-SM20 – 19 13/16" Surface mount active strap hinge. – 5/16" Thick hinge leaf. – Left shown. 34 3/8" 2" 1 3/4" 3 1/4" 2 3/4" 4 1/4" 2" 3 1/4" 1 3/4" 2 3/4" 3 1/4" 1" 31 15/16" 4 1/4" 2" 1 3/4" 19 13/16" 4 1/4" 1" 1 1/4" 10 1/2" 10 1/2" 10 1/2" 1" SH-T-SM35 – 34 3/4" Active strap hinge. – 5/16" Thick hinge leaf. – Left shown. Active surface mount strap hinges. SH-T-SM20 19 13/16” Active surface mount strap hinge. SH-T-SM32 31 15/16” Active surface mount strap hinge. SH-T-SM35 34 3/8” Active surface mount strap hinge. ** Specify if active strap hinges are surface mount or mortise mount.** Door handing is required. Custom sizes are available. Provided with 5/16” x 1 1/2” lags. Additional hinge screws. BH-SCREWS-REG 1 1/2” BH-SCREWS-LG 2 1/2” LAG-1 15/16” x 1/2” Dome 1/2" Additional lag bolt covers. LAG-2 1” x 1/2” Square 1/2" 1 5/16" LAG-3 7/8” x 1/2” Cylindrical 1/2" 1" 7/8" PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited. Revised 12/01/14 Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w . s u n v a l l e y b r o n z e . c o m 21-21 BEAN DUMMY STRAP HINGES 5 5/16" 1 1/8" 1 1/4" 5 13/16" SH-B13 – 13" Bean decorative dummy strap hinge. 6 5/16" 6 5/16" 1 1/8" 1 1/4" SH-B15 – 15" Bean decorative dummy strap hinge. 10 1/4" 10 1/4" 7 3/4" 3 3/16" 1 3/16" 3 3/16" 2 5/8" 1 1/4" 7 3/4" SH-B18 – 18" Bean decorative dummy strap hinge. 1 1/2" 23" 1 3/8" 2 1/16" 3 3/16" 2 1/16" 1 1/4" 5 13/16" 1 1/8" SH-B14 – 14" Bean decorative dummy strap hinge. 18" 1 3/8" 15" 1 3/8" 2 1/16" 3 3/16" 1 15/16" 1 1/4" 5 5/16" 14" 1 3/8" 13" 3 3/16" Illustrations are for demonstration purposes only. 1 3/16" SH-B23 – 23" Bean decorative dummy strap hinge. Bean dummy strap hinges. SH-B13 13” Bean decorative dummy strap hinge. SH-B14 14” Bean decorative dummy strap hinge. SH-B15 15” Bean decorative dummy strap hinge. SH-B18 18” Bean decorative dummy strap hinge. SH-B23 23” Bean decorative dummy strap hinge. Custom sizes are available. Provided with 5/16” x 1 1/4” lags. LAG-1 15/16” x 1/2” Dome 1/2" Additional lag bolt covers. LAG-2 1” x 1/2” Square 1/2" 1 5/16" LAG-3 7/8” x 1/2” Cylindrical 1/2" 1" 7/8" PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited. Revised 12/01/14 Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w . s u n v a l l e y b r o n z e . c o m 21-22 BEAN DUMMY STRAP HINGES Illustrations are for demonstration purposes only. 3" 3 3/4" 1 3/4" 33" 1 1/4" 10 1/8" 10 1/8" 10 1/8" 1 3/8" SH-B33 – 33" Bean decorative dummy strap hinge. 3" 3 3/4" 1 5/8" 36" 1 1/4" 8 5/16" 8 5/16" 8 5/16" 8 5/16" 1 3/8" 3 1/8" 1 5/8" 40" 1 1/4" 9 5/16" 9 5/16" 9 5/16" 9 5/16" 3 3/4" SH-B36 – 36" Bean decorative dummy strap hinge. 1 3/8" SH-B40 – 40" Bean decorative dummy strap hinge. Bean dummy strap hinges. SH-B33 33” Bean decorative dummy strap hinge. SH-B36 36” Bean decorative dummy strap hinge. SH-B40 40” Bean decorative dummy strap hinge. Custom sizes are available. Provided with 5/8” x 1 1/4” lags. LAG-1 15/16” x 1/2” Dome 1/2" Additional lag bolt covers. LAG-2 1” x 1/2” Square 1/2" 1 5/16" LAG-3 7/8” x 1/2” Cylindrical 1/2" 1" 7/8" PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited. Revised 12/01/14 Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w . s u n v a l l e y b r o n z e . c o m 21-23 NARROW FLEUR DE LIS DUMMY STRAP HINGES 1 1/4" 1 1/4" SH-FDL-N12 – 12" Narrow Fleur de Lis dummy strap hinge. 2 3/8" 7/8" 2" 1 1/4" 7 3/8" 7 3/8" 2" SH-FDL-N14 – 14" Narrow Fleur de Lis dummy strap hinge. 1 1/16" 18" 10 3/4" 2 3/8" 1 3/8" 2 3/8" 2" 8 3/4" 7/8" 14" 1 1/16" 1 3/16" 7/8" 12" 1 1/16" Illustrations are for demonstration purposes only. 2" SH-FDL-N18 – 18" Narrow Fleur de Lis dummy strap hinge. Narrow Fleur de Lis dummy strap hinges. SH-FDL-N12 12” Narrow fleur de lis dummy strap hinge. SH-FDL-N14 14” Narrow fleur de lis dummy strap hinge. SH-FDL-N18 18” Narrow fleur de lis dummy strap hinge. Custom sizes are available. Provided with #8 x 1 1/4” oval wood screws. PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited. Revised 12/01/14 Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w . s u n v a l l e y b r o n z e . c o m 21-24 SMALL FLEUR DE LIS DUMMY STRAP HINGES 1 1/4" 7 1/8" 24" 7 1/8" 2 7/16" 1 3/4" 2 9/16" 1 1/8" 1 3/4" 1 1/4" 2 7/16" SH-FDL-S14 – 14" Fleur de Lis dummy strap hinge. SH-FDL-S12 – 12" Fleur de Lis dummy strap hinge. 18" 10 1/4" 2 9/16" 1 7/8" 2 9/16" 2 7/16" 1 1/4" 10 1/8" 10 1/8" 2 9/16" 8 5/16" 1 1/8" 1 1/4" 14" 1 1/8" 1 3/4" 12" 1 1/8" Illustrations are for demonstration purposes only. 2 7/16" SH-FDL-S24 – 24" Fleur de Lis dummy strap hinge. SH-FDL-S18 – 18" Fleur de Lis dummy strap hinge. Small Fleur de Lis dummy strap hinges. SH-FDL-S12 12” Small Fleur de Lis dummy strap hinge. SH-FDL-S14 14” Small Fleur de Lis dummy strap hinge. SH-FDL-S18 18” Small Fleur de Lis dummy strap hinge. SH-FDL-S24 24” Small Fleur de Lis dummy strap hinge. Custom sizes are available. Provided with #8 x 1 1/4” oval wood screws. PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited. Revised 12/01/14 Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w . s u n v a l l e y b r o n z e . c o m 21-25 FLEUR DE LIS DUMMY STRAP HINGES Illustrations are for demonstration purposes only. 6 1/8" 4 7/8" 3 3/4" 1 1/4" 4 1/2" SH-FDL18 – 18" Fleur de Lis dummy strap hinge. 6 1/16" 6 1/16" 6 1/16" SH-FDL24 – 24" Fleur de Lis dummy strap hinge. 8" 8" 4 3/4" 3 3/4" 4 3/4" 3 5/8" 8" 2" 32" 2" 30" 1 1/4" 4 1/2" 1 1/4" 4 3/4" SH-FDL30 – 30" Fleur de Lis dummy strap hinge. 8 11/16" 8 11/16" 8 11/16" 4 3/4" SH-FDL32 – 32" Fleur de Lis dummy strap hinge. 36" 1 1/4" 7 1/2" 7 1/2" 7 1/2" SH-FDL36 – 36" Fleur de Lis dummy strap hinge. 7 1/2" 4 3/4" 2" 4" 4 3/4" 3 3/4" 2" 42" 4 3/4" 6 1/8" 4 7/8" 2 1/8" 3 1/2" 1 1/4" 2 1/8" 24" 18" 9" 1 1/4" 9" 9" 9" 4 3/4" SH-FDL42 – 42" Fleur de Lis dummy strap hinge. Fleur de Lis dummy strap hinges. SH-FDL18 18” Fleur de Lis dummy strap hinge. SH-FDL24 24” Fleur de Lis dummy strap hinge. SH-FDL30 30” Fleur de Lis dummy strap hinge. SH-FDL32 32” Fleur de Lis dummy strap hinge. SH-FDL36 36” Fleur de Lis dummy strap hinge. SH-FDL42 42” Fleur de Lis dummy strap hinge. Custom sizes are available. Provided with 5/16” x 1 1/4” lags. LAG-1 15/16” x 1/2” Dome 1/2" Additional lag bolt covers. LAG-2 1” x 1/2” Square 1/2" 1 5/16" LAG-3 7/8” x 1/2” Cylindrical 1/2" 1" 7/8" PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited. Revised 12/01/14 Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w . s u n v a l l e y b r o n z e . c o m 21-26 1 1/4" 6 15/16" 6 15/16" 3" 1 1/4" 24" 5" 3 7/16" 1 5/8" 3 7/8" 7/8" 2 3/8" 18" 4 3/4" Illustrations are for demonstration purposes only. 2 1/4" FLEUR DE LIS DUMMY STRAP HINGES 3 1/4" 2 1/8" 8 15/16" 8 15/16" 4" SH-FDL2-24 – 24" Fleur de Lis dummy strap hinge. SH-FDL2-18 – 18 5/16" Fleur de Lis dummy strap hinge. – Provided with #8 x 1 1/4" oval wood screws. 6 1/4" 3" 7" 4" 1 5/8" 33" 2 1/2" 8 3/16" 8 3/16" 5 1/2" 8 3/16" SH-FDL2-33 – 33" Fleur de Lis dummy strap hinge. 6 1/4" 3" 7" 4" 1 5/8" 39" 2 1/2" 7 3/4" 7 3/4" 7 3/4" 7 3/4" 5 1/2" SH-FDL2-39 – 39" Fleur de Lis dummy strap hinge. 6 1/4" 3" 7" 4" 1 5/8" 45" 2 1/2" 9 1/4" 9 1/4" 9 1/4" 9 1/4" 5 1/2" SH-FDL2-45 – 45" Fleur de Lis dummy strap hinge. Fleur de Lis dummy strap hinges. SH-FDL2-18 18” Fleur de Lis dummy strap hinge. SH-FDL2-24 24” Fleur de Lis dummy strap hinge. SH-FDL2-33 33” Fleur de Lis dummy strap hinge. SH-FDL2-39 39” Fleur de Lis dummy strap hinge. SH-FDL2-45 45” Fleur de Lis dummy strap hinge. Custom sizes are available. LAG-3 7/8” x 1/2” Cylindrical 1 5/16" LAG-2 1” x 1/2” Square 1/2" LAG-1 15/16” x 1/2” Dome 1" 1/2" Additional lag bolt covers. 1/2" Provided with 5/16” x 1 1/4” lags. 7/8" PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited. Revised 12/01/14 Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w . s u n v a l l e y b r o n z e . c o m 21-27 DUMMY STRAP HINGES 2 1/4" 1" 4" 1" 3 1/16" 15 5/8" 7/8" 4 3/4" Illustrations are for demonstration purposes only. 1" 3" 6" 4" 1 7/16" SH-G16 – 15 5/8" Decorative dummy strap hinge. Dummy strap hinges. SH-G16 15 5/8” Dummy strap hinge. Custom sizes are available. Provided with #8 x 1 1/4” oval wood screws. PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited. Revised 12/01/14 Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w . s u n v a l l e y b r o n z e . c o m 21-28 DUMMY STRAP HINGES 7 3/8" 1 1/8" 4 1/4" 7" 4 5/8" 4 1/4" 1 1/8" 4 5/8" 7 3/8" 4 1/4" 4 5/8" 7" 1 1/4" 5" 17 5/8" 36" 5" 1 1/8" 34" 4" 7 3/8" 15 1/4" SH-OD32 – 32" Ornate dummy strap hinge. – Left shown. SH-OD22 – 22" Ornate dummy strap hinge. – Left shown. 1 1/8" 4" 7" 5 3/8" 1 1/4" 4" 5" 4 5/8" 5" 1 1/8" 32" 1 1/4" 7" 1 1/4" 22" 1 1/8" Illustrations are for demonstration purposes only. 1 1/8" 4" 19 1/4" 7 3/8" 4 1/4" SH-OD36 – 36" Ornate dummy strap hinge. – Left shown. SH-OD34 – 34" Ornate dummy strap hinge. – Left shown. Dummy strap hinges. SH-OD22 22” Ornate dummy strap hinge. SH-OD32 32” Ornate dummy strap hinge. SH-OD34 34” Ornate dummy strap hinge. SH-OD36 36” Ornate dummy strap hinge. Custom sizes are available. Provided with #10 x 1 1/2” oval wood screws. PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited. Revised 12/01/14 Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w . s u n v a l l e y b r o n z e . c o m 21-29 DUMMY STRAP HINGES 5 1/2" 5 1/2" 5 1/2" 5 1/2" 3 1/2" 2 5/8" 2 3/4" 4 1/8" 27 1/4" 1 13/16" Illustrations are for demonstration purposes only. 3" SH-D27 – 27 1/4" Decorative dummy strap hinge. Dummy strap hinges. SH-D27 27 1/4” Dummy strap hinge. Custom sizes are available. Provided with #10 x 1 1/2 oval wood screws. PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited. Revised 12/01/14 Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w . s u n v a l l e y b r o n z e . c o m 21-30 DUMMY STRAP HINGES Illustrations are for demonstration purposes only. 2 1/2" 2 1/2" 18" 1 1/4" 7 3/4" 7 3/4" 1 1/4" SH-RT18 – 18" Decorative dummy strap hinge. 2 1/2" 2 1/2" 24" 1 1/4" 10 3/4" 10 3/4" 1 1/4" SH-RT24 – 24" Decorative dummy strap hinge. 2 1/2" 2 1/2" 33" 1 1/4" 10 1/8" 10 1/8" 10 1/8" 1 1/4" SH-RT33 – 33" Decorative dummy strap hinge. Dummy strap hinges. SH-RT18 18” Dummy strap hinge. SH-RT24 24” Dummy strap hinge. SH-RT33 33” Dummy strap hinge. Custom sizes are available. Provided with 5/16” x 1 1/4” lags. LAG-1 15/16” x 1/2” Dome 1/2" Additional lag bolt covers. LAG-2 1” x 1/2” Square 1/2" 1 5/16" LAG-3 7/8” x 1/2” Cylindrical 1/2" 1" 7/8" PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited. Revised 12/01/14 Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w . s u n v a l l e y b r o n z e . c o m 21-31 DUMMY STRAP HINGES Illustrations are for demonstration purposes only. 5/8" 1 1/4" 7 1/2" 7 1/2" 3" 3" 4 5/8" 24" 4 5/8" 18" 5/8" 1 1/4" 1 1/4" SH-SQ-HL18 – 18" Dummy strap hinge w/hinge barrel. 10 3/4" 36" 9 15/16" SH-SQ-HL33 – 33" Dummy strap hinge w/hinge barrel. 9 15/16" 1 1/4" 3" 4 5/8" 3" 4 5/8" 9 15/16" 1 1/4" SH-SQ-HL24 – 24" Dummy strap hinge w/hinge barrel. 33" 5/8" 1 1/4" 10 3/4" 5/8" 1 1/4" 10 15/16" 10 15/16" 10 15/16" 1 1/4" SH-SQ-HL36 – 36" Dummy strap hinge w/hinge barrel. Dummy strap hinges. SH-SQ-HL18 18” Dummy strap hinge w/ dummy hinge barrel. SH-SQ-HL24 24” Dummy strap hinge w/ dummy hinge barrel. SH-SQ-HL33 33” Dummy strap hinge w/ dummy hinge barrel. SH-SQ-HL36 36” Dummy strap hinge w/ dummy hinge barrel. Custom sizes are available. Provided with 5/16” x 1 1/4” lags. LAG-1 15/16” x 1/2” Dome 1/2" Additional lag bolt covers. LAG-2 1” x 1/2” Square 1/2" 1 5/16" LAG-3 7/8” x 1/2” Cylindrical 1/2" 1" 7/8" PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited. Revised 12/01/14 Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w . s u n v a l l e y b r o n z e . c o m 21-32 DUMMY STRAP HINGES Illustrations are for demonstration purposes only. 1 1/2" 2 3/4" 18" 1 1/4" 7 3/4" 7 3/4" 1 1/4" SH-SQ18 – 18" Decorative dummy strap hinge. 3" 1 1/2" 24" 1 1/4" 7 3/16" 7 3/16" 7 3/16" 1 1/4" SH-SQ24 – 24" Decorative dummy strap hinge. Dummy strap hinges. SH-SQ18 18” Dummy strap hinge. SH-SQ24 24” Dummy strap hinge. Custom sizes are available. Provided with #10 x 1 1/2 oval wood screws. PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited. Revised 12/01/14 Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w . s u n v a l l e y b r o n z e . c o m 21-33 CABINET HINGE FINIALS 1/16" BHCF-FDL Fleur de Lis finial. BHCF-FLAT Flat cabinet finial. 5/16" BHCF-RDG Ridge cabinet finial. 5/16" BHCF-STPL Steeple cabinet finial 11/16" BHCF-FREN French cabinet finial. 5/16" 5/16" 3/8" 5/8" 5/16" BHCF-BUTN Button cabinet finial. 1/2" 1/4" 5/8" BHCF-BALL Ball cabinet finial. 5/16" BHCF-DOME Dome cabinet finial. 5/16" 5/16" 5/16" BHCF-ACRN Acorn cabinet finial. 1/8" 3/8" 9/16" Illustrations are for demonstration purposes only. 5/16" BHCF-URN Urn cabinet finial. PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited. Revised 12/01/14 Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w . s u n v a l l e y b r o n z e . c o m 21-34 25000 SERIES CABINET HINGES Illustrations are for demonstration purposes only. 1 3/4" 5/16" 5/16" BHC-25150 – 1 1/2" x 2 1/2" cabinet hinge. – Shown w/flat finial. – Leaf thickness .092. 2" 2 1/2" 2 1/2" 2 1/2" 1 1/2" BHC-25175 – 1 3/4" x 2 1/2" cabinet hinge. – Shown w/flat finial. – Leaf thickness .099. 5/16" BHC-25200 – 2" x 2 1/2" cabinet hinge. – Shown w/flat finial. – Leaf thickness .099. Cabinet hinges. BHC-25150 1 1/2” x 2 1/2” Cabinet hinge w/finial. BHC-25175 1 3/4” x 2 1/2” Cabinet hinge w/finial. BHC-25200 2” x 2 1/2” Cabinet hinge w/finial. Call for handing options. Cabinet handing is required. Finial style must be specified. Custom sizes are available. PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited. Revised 12/01/14 Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w . s u n v a l l e y b r o n z e . c o m 21-35 CABINET STRAP HINGES 3/4" 5 5/16" 2 1/16" 1" 12 9/16" 3" 1 7/16" Illustrations are for demonstration purposes only. 5 5/16" 3/4" 5/8" SH-B-12-ACT-CK – 12 9/16" Active cabinet strap hinge. – Left shown w/button finial. – 1 7/16" Heel. Cabinet strap hinges. SH-B12ACT-CK 12 9/16” Active cabinet strap hinge w/finial. ** Cabinet strap hinges surface mount to face of cabinet stile and door. Provided with #8 wood screws for other options. Please call. Call for handing options. Cabinet door handing is required. Finial style must be specified. Custom sizes are available. PROPRIETARY AND CONFIDENTIAL: The information contained in this drawing is the sole property of Sun Valley Bronze. Any reproduction in part or as a whole without the written permission of Sun Valley Bronze is prohibited. Revised 12/01/14 Te l 2 0 8 . 7 8 8 . 3 6 3 1 • To l l F r e e 8 6 6 . 7 8 8 . 3 6 3 1 • F a x 2 0 8 . 7 8 8 . 1 3 0 6 • w w w . s u n v a l l e y b r o n z e . c o m 21-36
© Copyright 2025 ExpyDoc
