STX 6600 Manual

The STX 6600 is a straight column
Line Array featuring six high power
6.5” custom designed neodymium
woofers and six advanced design
planar magnetic Ribbon drivers in a
coax configuration with a unique
waveguide for wide 110 degrees
horizontal coverage.
Ultra-fast transient response and
higher instantaneous peak level for
faithful signal reproduction and
improved dynamic range.
The highly controlled vertical
dispersion of the array and excellent
coupling of the ribbon drivers at high
frequency yields the ultimate hi fidelity
long throw system.
True line array performance provides
dramatically increased intelligibility in
highly reverberant spaces.
Single box construction with integrated
fly points and internal passive crossover
for lower cost installation.
Improved front to back SPL over the
entire audience area, typically +/- 2db
Stix and Drums LLC 1990 N. McCulloch Blvd. Ste. D222 Lake Havasu City, AZ Voice: 928.733.6002 Fax: 928.453.5550
[email protected] www.stixanddrums.com
Introduction
Thank you for choosing Stix & Drums. When your speakers are installed and used properly, you can expect
exceptional aural performance and years of trouble free service. Please read this manual thoroughly prior to
installation.
Safety Responsibilities and Liability
Information in this guide is meant only for the purpose of using the AmbiSonic Systems supplied mounting
equipment. All other rigging and/or structure support including wall securing hardware is considered part of
the venue and/or end-user supplied equipment and is not addressed in this guide.
AmbiSonic Systems assumes that a working knowledge of accepted rigging practices and safety will be applied
to all rigging materials and practices employed. All rigging or wall mounting should be performed by a professional
installer or installation company and should follow all state and local building codes. All fasteners should be rated at
a minimum of 3-5 times the actual determined load. All walls are not created equal (drywall, masonry, wood, etc.)
In some instances it will be necessary to install “Backing” plates or other reinforcement to assure proper mounting.
Remember that the weakest component determines the safety of the entire rigging assembly. Prior to securing the
array, always inspect all hardware components for wear, deformations, corrosion and missing or damaged parts.
Also confirm that the venue attachment points are suitably load rated for the array. No information contained in
this guide is intended as a warranty on the part of AmbiSonic Systems.
Users assume all responsibility for the appropriate use of AmbiSonic Systems supplied rigging hardware and follow
at a minimum all applicable laws and regulations in force for each venue.
Anyone using this information assumes all liability arising from it’s use. Product abuse, use of the product not in
accordance with AmbiSonic Systems instructions or use in an application which the product has not been designed
for is not covered under any AmbiSonic Systems warranty nor is AmbiSonic Systems liable for any loss or damage.
Stix and Drums LLC 1990 N. McCulloch Blvd. Ste. D222 Lake Havasu City, AZ Voice: 928.733.6002 Fax: 928.453.5550
[email protected] www.stixanddrums.com
Attaching Coupling Brackets (BKT-CP66)
For multiple stacked arrays
Remove the M10 Flathead Screws
(4 places each side)
Coupling Brackets
(BKT-CP66) (2)
Attach the coupling plates with the
removed M10 flathead screws
All attachment points for coupling brackets are reinforced with internal steel brackets for
maximum strength and reliability.
Wall Mounting Kit (BKT-WM66)
For multiple stacked arrays
Upper Bracket Assembly
Upper Bracket
Pivot Right Pin
Pivot Left Pin
Down-angle adjustment holes
Rotation Locking Fastener
Wall Mounting Bracket
Lower Bracket Assembly
Pivot Right Pin
Lower Bracket
Pivot Hole
Pivot Left Pin
Rotation Locking Fastener
Wall Mounting Bracket
Attaching Upper and Lower Wall Mounting Brackets
Upper Bracket
Install the upper bracket to the STX6600 by first
removing the top rear M10 flathead screws from
the enclosure, then place the upper bracket in the
predetermined down angle position (see Fig.1),
insert the supplied M10 button head screws
through the appropriate hole in the bracket and
secure the screws.
Down-angle Adjustment
Upper holes labeled “BOX 2”
are for down-angle adjustment of
0 - 2.5 degrees for a column stack
of two (2) STX6600
Lower holes labeled “BOX 3”
are for down-angle adjustment of
0 - 2.5 degrees for a column stack
of three (3) STX6600
Fig. 1
BOX 2
BOX 3
0
0.5
1.0
1.5
2.0
2.5
Lower Bracket
Install the bottom bracket to the STX6600 by
removing the bottom rear M10 flathead screws,
then place the bottom bracket in position as
shown, insert the supplied M10 button head
screws through the bracket and tighten.
If the column will have any down angle, the
screws should not be tightened completely
as they are the pivot point for rotation.
Once the column has been mounted and
adjusted for angle, you can then tighten
the pivot screws.
Wall Mounting
Wall Mount Bracket Spacing
Wall Mount Hole Spacing
10.945
STX6600
STX6600
97
7.000
71.91
69.70
2.277
1.462
0.3
2.462
STX6600
STX6600
Wall Mount Bracket Right & Left Hand
Left Rotation
STX6600
Pivot
Dimensions shown are from the top
of each wall mount bracket.
Right Rotation
All wall mounting should be performed by a professional installer or installation company and should
follow all state and local building codes. All fasteners should be rated at a minimum of 3-5 times the
actual determined load. All walls are not created equal (drywall, masonry, wood, etc.)
In some instances it will be necessary to install “Backing” plates or other reinforcement to assure
proper mounting.
Pivot
STX6600
111.20
STX6620
Typical Column Examples
STX6600 & STX6620
(2) STX6600
(3) STX6600
Attaching MM-120 Wall Mounting Brackets
3.44
2.75
2.00
5.27
3.75
2.50
.41 4X
.39 6X
4.25
9.00
4.00
7.75
6.88
5.00
4.25
.406 2X
2.00
.38 4X
.41 X .50 SLOT
MM-120 WITH WP-16 OPTIONAL STUD PLATE
Wall Mount Plate
.41X.72 SLOT 2X
Speaker Mounting Plate
13.52
10.88
14.38
50° MAX.
9.00
9.00
FULLY EXTENDED ARM AT MAX. DOWN TILT ANGLE
Fully Extended - Max. Down Tilt
2.76
70
15°
MAX.
FULLY STOWED ARM AT MAX. UP TILT ANGLE
5.00
127
16.64
Fully Stowed - Max. Up Tilt
MM-120 ATTACHED TO STX6600
All wall mounting should be performed by a professional installer or installation company and should
follow all state and local building codes. All fasteners should be rated at a minimum of 3-5 times the
actual determined load. All walls are not created equal (drywall, masonry, wood, etc.)
In some instances it will be necessary to install “Backing” plates or other reinforcement to assure
proper mounting.
WARNING:
Mounting and/or suspension of loudspeakers requires experienced professionals. Improperly installed
loudspeakers can result in property damage, personal injury and/or liability to the installing contractor.
Always install safety cables.
8
5
6
7
4
REAR MOUNTED ILLUSTRATION (8" ARM TUBE)
2-7090
SPEAKER ADAPTER PLATE
1/8" THICK STEEL PLATE
2-7086
PIVOT BRACKET
1.75 SQ X .12 TUBE
2-7097
TRUSS HEAD BINDING POST SCREW
3/8" DIA. BARREL X 2.063" LONG
X 1/4-20 THREAD
2-7088
PIVOT U-BRACKET
SCREWED TO TUBE
D
Attaching MM-060 Wall Mounting Brackets
2-7095
THREADED ROD
FOR REAR AND
BOTTOM MOUNTED
60 lbs. maximum load
C
3.75
2.75
DIMENSIONS
12.00
2.00
7.25
NYLON WASHER
3/8 ID X 1.25 OD (2X)
5.00
45°
4.00
6.00
4.25
B
3.75
2.75
2.00
1.56
8.00
6.00
45° MAX
4.25
5.00
2.25
.88
.50
@45 DEGREE TILT
45 degrees Max. Down Tilt
2.50
3.58
1.88
Speaker Mounting2.25
Plate
45 degress Max. Up Tilt
A
Wall Mount Plate
PROPRIETARY AND CONFIDENTIAL
REVISIONS
Notes:
Unless Otherwise Specified
ZONE REV.
8
7
DESCRIPTION
DRAWN
DATE
01
REVISED CABLE PAS THRU HOLE
LOCATIONS. ADDED BOTTOM MOUNTED
ILLUSTRATIONS. ADDED WALL PLATE
COVER
TBA
04/30/13
02
REVISED WALL PLATE ASSY AND COVER
TBA
05/08/13
6
APPROVED
THIS DRAWING IS THE PROPERTY OF ALLEN
PRODUCTS CO. AND EMBODIES A PROPRIETY
DESIGN ORIGINATED BY ALLEN PRODUCTS CO.
ALL DESIGN, MANUFACTURE, REPRODUCTION,
USE AND SALE RIGHTS REGARDING THE SAME
ARE EXPRESSLY RESERVED. THIS DRAWING MAY
NOT BE REPRODUCED OR INFORMATION
HEREIN TRANSMITTED IN ANY WAY WITHOUT
WRITTEN CONSENT FROM ALLEN PRODUCTS
CO. ALL PATENT RIGHTS HERETO ARE
EXPRESSLY RESERVED BY ALLEN PRODUCTS
CO. SIGNAL HILL, CALIFORNIA
UNLESS OTHERWISE S
DIMENSIONS ARE IN IN
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
TWO PLACE DECIMAL
THREE PLACE DECIMA
INTERPRET GEOMETRIC
TOLERANCING PER:
MATERIAL
FINISH
THIRD ANGLE PROJECTION
5
4
DO NOT SCALE DRA
FILE LOCATION: E:\ENGINEERING\PROJECTS-PRELIMINARY DRAWINGS\PROJ-301-UP\PROJ-502 M
5.00
127
2.75
70
MM-060 ATTACHED TO STX6600
All wall mounting should be performed by a professional installer or installation company and should
follow all state and local building codes. All fasteners should be rated at a minimum of 3-5 times the
actual determined load. All walls are not created equal (drywall, masonry, wood, etc.)
In some instances it will be necessary to install “Backing” plates or other reinforcement to assure
proper mounting.
WARNING:
Mounting and/or suspension of loudspeakers requires experienced professionals. Improperly installed
loudspeakers can result in property damage, personal injury and/or liability to the installing contractor.
Always install safety cables.
Fly Points
Fly points (4) are positioned on the top of each enclosure and (1) located at the bottom center.
Top fly points (4)
Bottom rear fly point (1)
(Pull back adjustment)
All fly points are reinforced
with internal steel brackets
for maximum strength
and reliability
Remove the appropriate M10 flathead screws. Replace M10 flathead screws
with M10 Forged Steel Eye-bolts.
Top fly points
for hanging.
Bottom rear fly point for
down-angle adjustment
(Pull back adjustment)
(Use only M10 Forged Steel Eye-bolts)
STX 6600 Specifications
7.165
182
1.693
43
M10 (17 Plc's.)
Loop Output
Input
-
4.724
120
1.693
43
+
Input
4ohms
-
NL4 Speakon Connectors
+
Loop
Output
TM
Screw terminal barrier strip
By
Subwoofer
Model STX 6600
Made in Phillppines
10.000
255
TOP VIEW
INPUT PLATE
1.693
43
3.94
100
1.693
43
10.550
268
4.724
120
4.724
120
FRONT VIEW
1.693
43
SIDE VIEW
5.276
134
1.693
43
38.00
966
5.00
127
2.76
70
BACK VIEW
SPECIFICATIONS
System Type
Coaxial, ribbon driver, line array, two-way, single sealed enclosure
Driver Components
(6) 6” ribbon drivers + (6) 6.5” paper/Kevlar composite mid-bass drivers
Crossover
Passive, custom
Frequency Response¹
70Hz - 20kHz @ -6db
Maximum SPL
128db continuous, 138db peak
System Coverage
110 degree horizontal, 20 degrees vertical (asymmetrical)
Sensitivity, 1m/2.83V
101db
Power Handling
720W AES, 1100W IEC long term, 1400W IEC short term
Recomended Amplifier Power @ 4ohms
500W-2000W (FTC) @ 4 ohms
Rated Impedance
6 ohms
Input Connectors
Screw terminal barrier strip and dual NL4 speakon connectors
Enclosure
Closed box alignment, 18mm marine plywood, heavily damped and braced
Mounting Options
(17) M10 fly points, (4) M8 points for wall mount option
Accessories (optional)
Wall Mounting Kit(BKT-WM66) for multiple stacked arrays
L Bracket Kit(BKT-L66) for flying arrays under DRM215 subwoofer(s)
Coupling Brackets(BKT-CP66)
Allen Products MM-060 / MM-120 for single box wall mounting
Dimensions, (H x W x D) inches (mm)
Height 38.03” (966 mm) Width 10.550” (268 mm) Depth 10.04” (255 mm)
Weight, net
60.0 lbs. (27kgs)
Warranty
Limited 5-year warranty
ISOMETRIC VIEW
Warranty
Ambisonic Systems LLC (Ambisonic) Warranty on Stix & Drums ‘Products’ is in effect for a period of 5 years
from the date of first consumer purchase. Except as outlined below, your Stix & Drums Warranty covers all
defects in material and workmanship as long as the product is properly used and maintained.
If the Product is deemed defective by Ambisonic, Ambisonic will at its option, repair or replace the Product.
If the defective Product cannot be repaired or is no longer available for replacement, Ambisonic may replace
the Product with a current equivalent model of equal or greater value.
Under terms of this Warranty, the Product must be returned to an authorized Stix & Drums dealer or Ambisonic.
Return shipping and associated costs for exchanges or repairs is the sole responsibility of the original purchaser.
Limitations:
This limited Warranty does not cover failure of the Product resulting from improper installation, misuse, abuse,
accident, neglect, mishandling, or wear and tear from ordinary use or environmental deterioration.
This limited Warranty does not cover cosmetic damage, including paint damage, or consequential damage to
the other components or premises which may result for any reason from the failure of the Product.
This limited Warranty is null and void for Products not used in accordance with Ambisonic’s instructions.
This limited Warranty is null and void for Products with altered or missing serial numbers and for Products not
purchased from an authorized Stix & Drums dealer.
This limited Warranty terminates if you sell or otherwise transfer this Product to another party.
Stix and Drums LLC 1990 N. McCulloch Blvd. Ste. D222 Lake Havasu City, AZ Voice: 928.733.6002 Fax: 928.453.5550
[email protected] www.stixanddrums.com

Download Report