Installation Guide for BLC -015 V2.2 Lock Controller BLC-015 w/Battery charger August.05.2014 August.05.2014 HSD HSD TEAM TEAM Union Union Community Community Co., Co., Ltd. Ltd. 1. Power Connection DC 12V 2.5A Power Adapter 12V IN GND 12V OUT GND BAT(-) BAT(+) Backup Battery Interface 2 2. Board Feature & Connector Description J101 12V In / 12V Out / Wiegand/ RSRS- 485 1 9 2 8 3 7 4 6 5 5 6 4 7 3 8 2 9 1 J101 1 [ 12V IN ] : 12V Power Input 2 [ GND] : Ground 3 [ 12V OUT ] : 12V Power Out 4 [ GND] : Ground 5 [ Wie IN0 ] : Wiegand IN0 6 [ Wie IN1 ] : Wiegand IN1 7 [ GND] : Ground 8 [ 485-A] : RS-485A 9 [ 485-B] : RS-485B J51 9 [ COM ] 8 [ NO ] 7 [ NC ] 6 [ GND ] 5 [ IN2 ] 4 [ IN1 ] 3 [ IN0 ] 2 [ GND ] 1 [12V BAT ] : Common : Normal Open : Normal Close : Ground : Lock Status : Door Status : Inside Open : Battery(-) : Battery(+) J51 Battery IN / Input Port / Lock Control 3 3. Schematic for Door Lock Interface 4 4. Connecting RS-485 Interface ◈ RSRS- 485 Interface RS485A RS485B 5 5. Connecting Wiegand Interface ◈ Wiegand Interface WIN0 WIN1 GND 6 6. Connecting Dead-Bolt Type Door Lock (Fail Safe) ◈ Connect DeadDead- Bolt Lock SW52 0V <-> 12V (-)Black (+)Red DM0(+) 12V OUT GND RS485A GND DM0(-) EXIT RS485B EBEB- 030 Red : 12V Black : GND Green : NO Brown : COM 7 7. Connecting Strike Type Door Lock (Fail Safe) (-)Black (+)Red ◈ Connect Strike type Lock DM0(+) SW52 DM0(-) 0V <-> 12V 12V OUT GND GND RS485A EXIT RS485B Red : 12V Black : GND Green : NO Brown : COM EBEB- 030 8 8. Connecting EM Type Door Lock (Fail Safe) ◈ Connect EM Lock SW52 0V <-> 12V DM0(+) (+)Red (-)Black 12V OUT GND RS485A GND DM0(-) EXIT RS485B Red : 12V Black : GND Green : NO Brown : COM EBEB- 030 9 9. Connecting Auto-Door ( Contact Control ) ◈ Connect AutoAuto- Door Lock Auto Door Operating Part Auto Door Motor AutoAuto-Door Sensor AutoAuto-Door Monitor SW52 0V <-> 12V Sensor Input Line COM N.O. 12V OUT GND RS485A Red : 12V Black : GND Green : NO Brown : COM RS485B EBEB- 030 10 10. RS-485 ID & Open duration Setting ◈ SW1 Switch Feature ◈ RSRS- 485 ID Setting 5 4 3 21 RS485 ID 1 2 0 OFF OFF 1 OFF ON 2 ON OFF 3 ON ON OFF ON SW1 ◈ Lock Open Duration Setting Open Time (sec) SW1 3 4 5 0.2 OFF OFF OFF 0.5 OFF OFF ON 1 OFF ON OFF 1.5 OFF ON ON 2 ON OFF OFF 3 ON OFF ON 4 ON ON OFF 5 ON ON ON 11
© Copyright 2024 ExpyDoc