Partitions - Krea Grup

Partitions
F
Building New Solutions
Remodelling room partitioning often turns out to be expensive and with a lot involved. By
using Lindner’s easily removable partitions you can adapt your rooms to momentary requirements at any time. Lindner partition systems provide decisive advantages for your individual
requirements.
Various Systems for Lindner LVT Partitions:
• Metal partitions
F0 / F30 / F90 with G30- / G90-fanlight
• Chipboard partitions
F0 / F30 / F90 with G30- / G90-fanlight
• Plasterboard partitions
F0 / F30 / F90 with G30- / G90-fanlight
• Glazed partitions
F0 / F30
Subject to technical changes also without notiﬁcation.
F2
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
Table of Contents
LVT systems......................................................................................................... Code designation
LVT Partition .................................................................................................................................................................. 4
LVT Solid Partition System .................................................................................... System 100 .................................... 6
LVT Glazed Partition with Hook-on Aluminium Frame ........................................... System 110 .................................. 11
LVT Glazed Partition – ﬂush-fronted double-glazing ............................................ System 125 .................................. 15
LVT Glazed Partition – ﬂush-surface bonded double-glazing................................ System 137 .................................. 19
LVT Glazed Partition with Slim Line Glazing ......................................................... System 140 .................................. 23
Surfaces for Partitions and Wall Cladding ................................................................................................................... 27
Doors ........................................................................................................................................................................... 29
Installation System for Partition Systems ................................................................................................................... 35
Accessories ................................................................................................................................................................. 36
Great Ways to Organise Your Ofﬁce ........................................................................................................................... 39
LVT Partition for Inspection Chambers F30 .......................................................... System LM 500 ............................ 40
Instructions for Ordering, Installation and Use ............................................................................................................ 41
Standards and Regulations ......................................................................................................................................... 43
LW systems
Fully-Glazed Partitions GDL-IGG .......................................................................... System LW 600 ............................ 45
Lindner Fully-Glazed Partition ............................................................................... System LW 620 ............................ 48
Timber Framework Partition .................................................................................. System LW 640 ............................ 51
Fully-Glazed Partition ............................................................................................ System LW 650 ............................ 55
Lindner Safelite SL 90 ........................................................................................... System LW 660 F90 ..................... 58
Team Panel ........................................................................................................... System LW 670 ............................ 61
GK systems
Plasterboard Partition .................................................................................................................................................. 64
Lindner Akusto-Wand .................................................................................................................................................. 65
Lindner Fire Wall ................................................................................................... System LGK-530-BW................... 66
G30 Steel Frame Glazing in Plasterboard Partitions ............................................. System LGK-100-G30.................. 67
G90 Steel Frame Glazing in Plasterboard Partitions ............................................. System LGK-110-G90 .................. 69
G30 / F30 Frameless Glazing in Plasterboard Partitions ...................................... System LGK-120-G30/F30 .......... 71
G30 High-performance Sound-Insulation Glazing in Plasterboard Partitions ....... System LGK-140-G30.................. 75
Façade Sword, High-performance Sound-Insulation ............................................ System LGK-500-F0 .................... 77
F90 Access Panel in Plasterboard Shaft Walls or Solid Walls............................... System LGK-510-F90 .................. 78
F0 Access Panel in Plasterboard Partitions .......................................................... System LGK-520-F0 .................... 79
Subject to technical changes also without notiﬁcation.
F3
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
LVT Partition
Product Description
Fig. 1
Exploded view of partiton with inﬁll strip
Removable, non-load-bearing partitions for interior ﬁt-out
consisting of surface-ﬁnished wall panels, glazing and
door elements.
Lindner‘s LVT-partitions enable ﬂexible room design.
Changes can be carried out at any time.
After the initial installation it is simple to carry out changes
by just moving, removing or adding wall elements, or by
exchanging them (e.g. doors).
k6106
Fig. 2
Exploded view of linear strip
This partition system consists of a sandwich element and
can be build as linear or inﬁll strip system. The wall panels are made from 19-mm thick chipboard panels, melamine-coated according to DIN 68 765, Emission Class
E1. The panel edges are coated with 0.4-mm to 0.8-mm
thick melamine resin as standard. If necessary, 1.5-mm
to 3-mm thick plastic or solid wooden edges can also be
applied. These are then bevelled. Galvanised steel ﬁxing
hooks are screwed onto the reverse sides of the wall panels. Then the panels are ready for hooking into the system
studs. As an alternative, panels with real wood veneer on
chipboard or gypsum ﬁbre board or metal wall panels are
possible. Gaskets are used to seal joints on the ﬂoor/ceiling channels and on the stud.
k5349
Module
Module
Element A
Element A
Module
Element A
Module
Module
Element A
Module
Module
Element B
Element B
Module
Element A
Element C
Module
Element A
Element A
Inﬁll strip system
Module
Fig. 4
Element A
Linear modular system
Element B
Fig. 3
Subject to technical changes also without notiﬁcation.
F4
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
LVT Partition
The Substructure
Fig. 5
Floor/Ceiling channels with stud
The substructure consists of folded and roll-formed steel
proﬁles either galvanised or coated.
When PVC-ﬂoor coverings are used, the ﬂoor channel is
designed that it can be ﬁxed and sealed to the side of it,
glued and sealed. The standard surface for ﬂoor/ceiling
channel is powder-coated or coil-coated.
The wall panels are held in the system stud by ﬁxing
hooks made of galvanised steel.
These studs consist of punched, galvanised steel proﬁles.
There are openings in the middle for horizontal installation of electrical cables, etc.
k6102
Shelving System
Fig. 6
Shelf bracket with shelf inserts
The design of this shelving system is ideal for ofﬁces. In
our partitions there is a concealed hook-on system for
shelf brackets attached in the vertical shadow gap along
the entire room height. These can be individually adjusted. The requirement upon load capacity is in accordance
with DIN 4103-Bracket Loads.
k10212
Organisational System
Fig. 7
Installing organiser panels is also useful in ofﬁces. These
are hooked into the system studs instead of a wall panel
and are used to fasten numerous organisational materials, such as pigeonholes, furniture or desk sets.
Subject to technical changes also without notiﬁcation.
F5
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
LVT Solid Partition System
System 100
Fig. 8
Subject to technical changes also without notiﬁcation.
F6
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
LVT Solid Partition System
System 100
Fig. 9
System description
A non-load bearing solid partition system with light weight
construction that meets the wide variety of requirements
upon architectural styling and engineering. This movable
partition can be combined with various glazing and supplemented by numerous accessories.
Substructure:
This consists of folded and roll-formed steel sheet proﬁled
section elements, galvanised or coated.
Panelling:
Sandwich element construction with hook-on system
Chipboard:
19 mm, E1/B2
Metal panel:
13 mm
Support panel: 19 mm, A2
Surface:
Metal, real wood veneer, melamine
resin, laminated sheet material
Shelving system / Ofﬁce equipment:
These are integrated/ﬁxed in the horizontal and vertical
joints. Fabric panels can be hung up provided they are
suitable for pin ﬁxings.
Joints and connections:
Joints:
Concealed in the vertical shadow gaps (along the entire
room height) there is a hook-on system attached for shelf
brackets. The crosswise organisation is ﬁxed in the horizontal joints.
Joint sealant:
Plastic proﬁles are used on the ﬂoor and ceiling channels
and on stud proﬁle elements.
Connections:
Recessed ﬂoor and ceiling junctions; alternatively: also
recessed wall junctions.
Special features:
- Easy to demount and re-install
- Inspection-friendly handling for later installations
- Easy to combine with all LVT glazing variations
- Matches Lindner ﬂoor and ceiling systems
Field of application:
Ofﬁces
Industrial and factory rooms
Training and research rooms
Technical Data
Fireprooﬁng:
F0 / F30 / F90 as per DIN 4102
EI30 / EI60 as per EN 1364-1 (with metal panel)
Soundprooﬁng:
up to 54 dB Rw,P as per DIN EN ISO 140-03
Static requirements:
Installation area type 1 and 2
Non-supporting partition as per DIN 4103
Height up to max. of 5 000 mm
Axial width up to max. of 1 500 mm
Weight:
34 – 38 kg/m² (chipboard)
38 – 42 kg/m² (metal)
Standard module widths:
1 200 – 1 300 mm
Joint width:
6 / 8 mm
Partition thicknesses:
100 and 125 mm (19 mm panelling)
89 and 100 mm (13 mm panelling)
Applicable standards:
DIN 18202, DIN 68100
Customized solutions are possible on request!
Subject to technical changes also without notiﬁcation.
F7
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
LVT Solid Partition System
Fig. 10
Vertical section of
Solid partition with chipboard panel
Fig. 11
Vertical section of
Solid partition with metal panel
Fig. 12
Horizontal section of
Module with chipboard panel
Fig. 13
Horizontal section of
Module with metal panel
Subject to technical changes also without notiﬁcation.
F8
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
LVT Solid Partition System
Fig. 14
Horizontal section of 90°-corner
Fig. 15
„Horizontal section of
T-junction on linear modular system“
Fig. 16
Horizontal section of
wall connection with shadow gap
Fig. 17
„Horizontal section of T-junction on post cap“
Fig. 18
Horizontal section
of wall connection without shadow gap
Fig. 19
Horizontal section of stop end
Subject to technical changes also without notiﬁcation.
F9
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
LVT Solid Partition System
Fig. 20
Horizontal section of steel frame
Fig. 22
Horizontal section of aluminium frame
Fig. 23
Horizontal section of wooden frame
Fig. 21
Vertical section of steel frame
Fig. 24
Horizontal section of aluminium frame
with tubular frame door leaf
Subject to technical changes also without notiﬁcation.
F10
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
LVT Glazed Partition with Hook-on Aluminium Frame
System 110
Fig. 25
Fig. 26
Subject to technical changes also without notiﬁcation.
F11
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
LVT Glazed Partition with Hook-on Aluminium Frame
System 110
Fig. 27
System description
A partition consisting of single-pane or thermopane glazing with hook-on type aluminium frame with a visible width
of 35 mm.
Substructure:
Consisting of folded and roll-formed steel sheet proﬁled
section elements, galvanised or coated.
Glazing:
Single-pane glazing with a single pane or thermopane
glazing.
The aluminium frames are hooked on later.
The frame surface can be enamelled or real wood veneer
is possible.
Design options:
Full glazing
Dado-height glazing
Fanlight glazing
All the glazing variations can be combined with the LVTsystem solid partition.
Joints and connections:
Joints:
Concealed in the vertical shadow gaps (along the entire
room height) there is a hook-on system attached for shelf
brackets.
Joint sealant:
Plastic proﬁles are used on the ﬂoor and ceiling channels
and on the stud proﬁle.
Connections:
Recessed ﬂoor, ceiling and wall junctions.
Field of application:
Ofﬁces
Industrial and factory rooms
Training and research rooms
Technical Data
Fireprooﬁng:
F0 / G30 / F30 as per DIN 4102
EI30 as per EN 1364-1
Static requirements:
Installation area type 1 and 2
Non-supporting partition as per DIN 4103
Height up to max. of 3 500 mm
Axial width up to max. of 1 500 mm
Weight:
20 – 60 kg/m² for fully glazed partition
Joint width:
6 / 8 mm
Partition thicknesses:
100 and 125 mm (19 mm panelling)
89 and 100 mm (13 mm panelling)
Glass thicknesses:
variable
Glass panes with integrated shutter are possible depending on partition thickness, also in the ﬁre protection
Applicable standards:
DIN 18202, DIN 1249, DIN EN ISO 12543
Customized solutions are possible on request!
Soundprooﬁng:
up to 46 dB Rw,P as per DIN EN ISO 140-03
Subject to technical changes also without notiﬁcation.
F12
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
LVT Glazed Partition with Hook-on Aluminium Frame
Fig. 28
Vertical section of glazed partition with jalousie
Fig. 29
Vertical section of aluminium door frame
Fig. 30
Horizontal section of linear modular system
Fig. 31
Horizontal section of aluminium door frame
Subject to technical changes also without notiﬁcation.
F13
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
LVT Glazed Partition with Hook-on Aluminium Frame
Fig. 32
Horizontal section of 90°-corner
Fig. 33
Horizontal section of T-junction on module via
glass facade connection
Fig. 34
Horizontal section of wall connection
Fig. 35
Horizontal section of stop end
Fig. 36
Vertical section of dado connection
Fig. 37
Horizontal section of T-junction on linear
modular system
Subject to technical changes also without notiﬁcation.
F14
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
LVT Glazed Partition – ﬂush-fronted double-glazing
System 125
Fig. 38
Fig. 39
Subject to technical changes also without notiﬁcation.
F15
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
LVT Glazed Partition – ﬂush-fronted double-glazing
System 125
Fig. 40
System description
A glazed partition consisting of two aluminium frames with
integrated panes, which hook into the system studs. The
panes are held in place by a frame at the perimeter with a
visible width of 35 mm.
Substructure:
This consists of folded and roll-formed steel sheet proﬁled
section elements, galvanised or coated.
Glazing:
This consists of a two-piece glazing element into each of
which a pane fastens. The visible width of the frame at
the perimeter is 35 mm. The two frames hook into a postand-beam construction. Glass thicknesses are possible
from 6 – 9 mm.
Design options:
Full glazing
Dado-height glazing
Fanlight glazing
possible with shutters for every option
All the glazing variations can be combined with the LVTsystem solid wall.
Joints and connections:
Joints:
Concealed in the vertical shadow gaps (along the entire
room height) there is a hook-on system attached for shelf
brackets.
Joint sealant:
Plastic proﬁles are used on the ﬂoor and ceiling channels
and on the stud proﬁle.
Connections:
Recessed ﬂoor, ceiling and wall junctions.
Field of application:
Ofﬁces
Industrial and factory rooms
Training and research rooms
Static requirements:
Installation area type 1 and 2
Non-supporting partition as per DIN 4103
partition height up to max. of 3 500 mm
Glazing height up to max. of 3 000 mm
Glazing width up to max. of 1 400 mm
Weight:
35 – 45 kg/m² for fully-glazed partition
Joint width:
6 / 8 mm
Partition thicknesses:
100 mm and 125 mm (19 mm panelling)
100 mm (13 mm panelling)
Applicable standards:
DIN 18202, DIN 1249, DIN EN ISO 12543
Technical Data
Customized solutions are possible on request!
Fireprooﬁng:
F0, F30 (as per DIN 41 02) as a three piece glazing
EI30 / EI60 as per EN 1364-1 as a three piece glazing
Soundprooﬁng:
up to 47 dB Rw,P as per DIN EN ISO 140-03
Fully-glazed partition
Subject to technical changes also without notiﬁcation.
F16
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
LVT Glazed Partition – ﬂush-fronted double-glazing
Fig. 41
Vertical section of glazed partition with jalousie
Fig. 42
Vertical section of aluminium door frame
Fig. 43
Horizontal section of linear modular system
Fig. 44
Horizontal section of aluminium door frame
Subject to technical changes also without notiﬁcation.
F17
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
LVT Glazed Partition – ﬂush-fronted double-glazing
Fig. 45
Horizontal section of 90°-corner
Fig. 46
Horizontal section of T-junction on module via
glass facade connection
Fig. 47
Horizontal section of wall connection
Fig. 48
Horizontal section of stop end
Fig. 49
Vertical section of dado connection
Fig. 50
Horizontal section of T-junction on linear
modular system
Subject to technical changes also without notiﬁcation.
F18
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
LVT Glazed Partition – ﬂush-surface bonded double-glazing
System 137
Fig. 51
Fig. 52
Subject to technical changes also without notiﬁcation.
F19
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
LVT Glazed Partition – ﬂush-surface bonded double-glazing
System 137
Fig. 53
System description
A glazed partition consisting of two aluminium frames with
panes glued on, which hook into the system studs. The
panes are ﬂush with the aluminium frame so that only the
20/32-mm adhesive surface behind is visible.
Substructure:
This consists of folded and roll-formed steel sheet proﬁled
section elements, galvanised or coated.
Glazing:
This consists of a two-piece aluminium frame onto each
of which a pane is glued. With this ﬂush design the visible
width of the adhesive surface is 20 mm, it being possible
for the proﬁled section to be as wide as 32 mm for ceiling
junctions (tolerance compensation).
The two frames hook into a post-and-beam construction.
Glass thicknesses are possible from 6 – 8 mm.
Bonding:
The proved structural glazing technology by Dow Corning
had been used for the bonding. This bonding technology
guarantees highest reliability and longevity.
Design options:
Full glazing
Dado-height glazing
Fanlight glazing
possible with shutters for every option
All the glazing variations can be combined with the LVTsystem solid partition.
Joints and connections:
Joints:
Concealed in the vertical shadow gaps (along the entire
room height) there is a hook-on system attached for shelf
brackets.
Joint sealant:
Plastic proﬁles are used on the ﬂoor and ceiling channels
and on the stud proﬁle.
Connections:
Recessed ﬂoor, ceiling and wall junctions.
Field of application:
Ofﬁces
Industrial and factory rooms
Training and research rooms
Technical Data
Fireprooﬁng:
F0, F30 (as per DIN 41 02) as a three-piece glazing
EI30 / EI60 as per EN 1364-1 as a three piece glazing
Soundprooﬁng:
up to 46 dB Rw,P as per DIN EN ISO 140-03
fully-glazed partition
Static requirements:
Installation area type 1 and 2
Non-supporting partition as per DIN 4103
Partition height up to max. of 3 500 mm
Glazing height up to max. of 3 000 mm
Glazing width up to max. of 1 500 mm
Weight:
35 – 40 kg/m² for fully-glazed partitions
Joint width:
6 / 8 mm
Partition thicknesses:
100 and 125 mm (19 mm panelling)
100 mm (13 mm panelling)
Adhesive:
Type:
following ETAG 002,
using structural glazing system
Temperature resistance:
-50° C to +150° C
Colour: Light-grey
Applicable standards:
DIN 18202, DIN 1249, DIN EN ISO 12543
Customized solutions are possible on request!
Subject to technical changes also without notiﬁcation.
F20
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
LVT Glazed Partition – ﬂush-surface bonded double-glazing
Fig. 54
Vertical section of glazed partition with jalousie
Fig. 55
Vertical section of aluminium door frame
Fig. 56
Horizontal section of linear modular system
Fig. 57
Horizontal section of aluminium door frame
Subject to technical changes also without notiﬁcation.
F21
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
LVT Glazed Partition – ﬂush-surface bonded double-glazing
Fig. 58
Horizontal section of 90°-corner
Fig. 59
Horizontal section of T-junction on module via
glass facade connection
Fig. 60
Horizontal section of wall connection
Fig. 61
Horizontal section of stop end
Fig. 62
Vertical section of dado connection
Fig. 63
Horizontal section of T-junction on linear
modular system
Subject to technical changes also without notiﬁcation.
F22
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
LVT Glazed Partition with Slim Line Glazing
System 140
Fig. 64
Fig. 65
Subject to technical changes also without notiﬁcation.
F23
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
LVT Glazed Partition with Slim Line Glazing
System 140
Fig. 66
System description
Glazing featuring frameless design with a vertical covering proﬁled section and visible width of 60 mm.
Substructure:
This consists of folded and roll-formed steel sheet proﬁled
section elements, galvanised or coated.
Glazing:
Single-pane glazing with single pane or thermopane glazing.
Design options:
Dado-height glazing
Fanlight glazing
All the glazing variations can be combined with the LVTsystem solid wall.
Field of application:
Ofﬁces
Industrial and factory rooms
Training and research rooms
Technical Data
Fireprooﬁng:
F0 / G30 as per DIN 4102
For international certiﬁcations, see Fire Protection Overview
Soundprooﬁng:
up to 46 dB Rw,P as per DIN EN ISO 140-03
Static requirements:
Installation area type 1 and 2
Non-supporting partition as per DIN 4103
Height up to max. of 3 500 mm
Axial width up to max. of 1 500 mm
Weight:
40 – 60 kg/m²
Joint width:
6 / 8 mm (on dado-height)
Partition thicknesses:
100 and 125 mm (19 mm panelling)
89 and 100 mm (13 mm panelling)
Glass thicknesses:
variable
Glass panes with integrated shutter are possible depending on partition thickness, also in the ﬁre protection.
Applicable standards:
DIN 18202, DIN 1249, DIN EN ISO 12543
Customized solutions are possible on request!
Subject to technical changes also without notiﬁcation.
F24
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
LVT Glazed Partition with Slim Line Glazing
Fig. 67
Vertical section of fanlight glazing
Fig. 68
Vertical section of steel door frame
Fig. 69
Horizontal section of linear modular system
Fig. 70
Horizontal section of linear modular system
Subject to technical changes also without notiﬁcation.
F25
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
LVT Glazed Partition with Slim Line Glazing
Fig. 71
Horizontal section of 90°-corner
Fig. 72
Horizontal section of T-junction
Fig. 73
Horizontal section of wall connection
Fig. 74
Horizontal section of stop end
Fig. 75
Vertical section of wall panel above glazing
Subject to technical changes also without notiﬁcation.
F26
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
Surfaces for Partitions and Wall Cladding
Wooden panel, perforated
sound-absorbing / sound-deadening
Fig. 76
System description
Our partitions and our wall claddings can be equipped
with different surfaces.
This wooden panel is constructed such that it can be
used in combination with nearly all systems. With different stampings and superstructural parts this panel can be
used for rooms with high acoustic requirements.
Structure:
Consisting of a top layer and a bracing wooden frame with
an acoustic panel inside. For sound absorbing demands
this panel can be ﬁtted out with additional plasterboard
inlays.
Surface:
Veneer
Laminated plastic
Lacquering
Possible hole patterns:
Form: round, quadratic, square
Size: 5 and 8 mm (Standard)
Special features:
- sound-absorbing
- sound-deadening
Field of application:
In LVT Solid Partitions, dado-height glazing
and wall claddings
Ofﬁces
Industrial and factory rooms
Training and research rooms
Sound absorption:
Assessed sound absorption value as per ISO 11654
αw = 0,50
Hole dimension 6 mm
Hole percentage 11%
Technical Data
Fireprooﬁng:
F0
Soundprooﬁng:
49 dB Rw,P as per DIN EN ISO 140-03
with Solid Partition Systems 100 mm each one- sided and
two- sided installed
Weight:
10 – 15 kg/m² (wall panel)
Dimensions:
max. b x h = 1200 mm x 3000 mm
Panel thickness:
19 mm
Subject to technical changes also without notiﬁcation.
F27
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
Surfaces for Partitions and Wall Cladding
Surfaces of Metal Wall Panels
Coil coating
Powder coating
A metallic base material is provided with an organic coating material in a continuous process (coil coating).
Electrostatically charged polyester-based powder particles are blown onto an earthed base material. Afterwards
the coating ﬁlm is cross-linked at approx. 180° C.
Base material:
Hot-dip galvanized (Sendzimir-galvanised) sheet metal
with a zinc deposit of approx. 7 µm = 100 g/m²; with zinc
deposited on both sides
Coating:
Priming coat and coat of ﬁnishing enamel with an average coat thickness of approx. 25 µm. Coat of protective
enamel on reverse side of 7 µm -10 µm thick.
Surface
RAL 9010
according to
Lindner
Plain
Gloss rate in
units
Approx. 24 E
according to
Gardner
DIN 67 530
60° measuring
angle
Degree of
reﬂection as a
percentage
Approx. 82 %
In addition to this, the visible surface is provided with an
approx. 120 µm thick, pull-off protective sheeting as protection during production and installation.
Base material:
Electrolytically galvanised thin-gage sheet metal with a
zinc deposit of 2.5 µm = 36 g/m², with zinc deposited on
both sides
Coating:
Coat of ﬁnishing enamel covering the base evenly.
Gloss rate in
units
Degree of
reﬂection as a
percentage
RAL 9010
according to
Lindner
Plain
Approx. 18 EH
according to
Gardner
DIN 67 530
60° measuring
angle
Approx. 82 %
RAL 9006
according to
Lindner
Plain
Approx. 57 EH
according to
Gardner
DIN 67 530
60° measuring
angle
Approx. 47 %
Surface
Properties:
- An even coating thickness and thus also an even appearance.
- Very good corrosion protection through use of a zinc/
enamel synergy effect.
- Edges of cuts are protected against corrosion through
the protective cathodic effect of zinc.
Properties:
- Very thick coat of enamel, providing good technical properties.
- Edges of cuts are also coated as a result of the manufacturing process and thus also protected against corrosion.
- Very good protection against corrosion through use of a
zinc/enamel synergy effect.
- Environmentally suitable, as the coating process is solvent-free.
Fig. 77
Fig. 78
Illustration of the structure of the coating of
coil-coated steel sheet
Visible side
Illustration of the structure of the coating of
powder-coated steel sheet
Visible side
Pull-off protective sheeting,
approx. 120 µm
Coat of finishing enamel,
approx. 25 µm
Zinc layer, approx. 7 µm
Steel core, 0.60-1.00 mm
Zinc layer, approx. 7 µm
Coat of finishing enamel
covering the base evenly
Zinc layer, approx. 2.5 µm
Steel core, 0.60-1.00 mm
Zinc layer, approx. 2.5 µm
Coat of protective
enamel, 7-10 µm
Subject to technical changes also without notiﬁcation.
F28
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
Doors
T0 Door element in LVT Partition
Fig. 79
Fig. 80
Aluminium door frame
Steel door frame
A slim aluminium door frame with decorative rebate and
a panel width of only 35 mm. This frame is delivered
with door leaves in various designs of solid chipboard or
glass.
Steel door frame in standard design with panel width of
40/55 mm. This frame can be delivered with a wide variety of rebates and wall thicknesses. It can also be integrated in any LVT partition system.
Technical Data:
- 6 and 8 mm wall joints possible
- For revolving doors
- With decorative rebate
- Panel width of 35 mm
Technical Data:
- Wall joints from 6-8 mm (standard)
- For revolving doors
- Panel width of 40/55 mm (standard)
- Wide variety of rebates possible
Door leaf options:
Wooden door leaf: Flush closing and with rebate
Glass door leaf: Clear glass and white satin-ﬁnish
Steel sheet door leaf: ﬂush closing
Aluminium frame door leaf
Door leaf options:
Wooden door leaf: Flush closing, with rebate, ﬂush with
reveal rebate, double-rebate opening action
Steel sheet door leaf: ﬂush closing, ﬂush with double rebate
Glass door leaf
Aluminium frame door leaf
Special feature:
For example: Closing equipment, switch in door frame
Special feature:
For example: Closing equipment or switch in door frame
Subject to technical changes also without notiﬁcation.
F29
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
Doors
T0 Door element in LVT Partition
Tubular frame door leaf, aluminium
Fig. 81
System description
Tubular frame door, which consists of aluminium and has
the smallest possible visible width. This door leaf is available with glass panes which have different thicknesses.
For soundprooﬁng it is possible to integrate an automatic
door seal.
Technical Data
Fireprooﬁng:
F0
Soundprooﬁng:
32 dB Rw,P according to DIN EN ISO 140-03
in aluminium door frame
Thickness of door leaf:
40 mm / 56 mm
Dimension of tubular frame:
Sidewise an on top:
86 mm
On bottom:
111 mm
Possible glass thickness:
6, 8, 10 and 24 mm
Fig. 82
Flush at the side of the hinge
Fig. 83
Flush at corridor side
Subject to technical changes also without notiﬁcation.
F30
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
Doors
T0 Door element in LVT Partition
Aluminium door frame with glass door leaf ﬂush
with surface on both sides
Fig. 84
Fig. 85
System description
Technical Data
Aluminium door frame ﬂush closing with double rebate
and a panel width of 35/65 mm.
The glass door leaf consists of a aluminium frame construction with safety glass panes glued on.
The door element is equipped with hinges for 3D adjustment.
Fireprooﬁng:
F0
Substructure:
Consisting of folded and roll-formed steel sheet proﬁled
section elements, galvanised or coated.
Bonding:
The proved structural glazing technology by Dow Corning
had been used for the bonding. This bonding technology
guarantees highest reliability and longevity.
Soundprooﬁng:
37 dB Rw,P as per DIN EN ISO 140-03
Partition thicknesses:
100 mm (19 mm panelling)
Dimensions:
Inside frame size
Height: max. 2 414 mm
Width: max. 1 264 mm
Technical Data:
- Panel width of 35/65 mm
- Door leaf thickness: 100 mm
- 6 and 8 mm safety glass
Adhesive:
Type:
following ETAG 002,
using structural glazing system
Temperature resistance:
-50° C to +150° C
Colour: Light-grey
Subject to technical changes also without notiﬁcation.
F31
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
Doors
T0 Door element in LVT Partition
Sliding Door
Fig. 86
System description
A sliding door integrated into the partition elements, with
pass-through design to match the partition elements. This
door element is possible up to the room height in several
variations. It can be installed in partition elements and in
double glazing systems. When opened, the door itself disappears into the void of the wall.
Options:
Solid sliding door element: Divided,with fanlight, roomhigh
Glass sliding door element: In clear glass or white satinﬁnished, divided, room-high
Technical Data
Dimensions:
- Partition thickness 100 mm
- Width of solid sliding door element 1 100 mm
- Width of glass sliding door element 1 200 mm
- Clear width 950 mm
- Height of element with fanlight or divided 3 400 mm
- Height of element, sliding door room-high 3 100 mm
- Panel width 35 mm
Installation characteristics:
- For 13 and 19 mm panelling
- 6 and 8 mm wall joint possible
- Sliding door can be used on the right-hand or left-hand
side
- Next to the sliding door in the „opening direction“ at least
a 1 000 mm wide element is necessary
- double leaf possible
Subject to technical changes also without notiﬁcation.
F32
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
Doors
T30-Türelement in LVT-Wand F30 / F90
T30 Door element in F30 / F90 LVT Partition
Fig. 87
System description
Technical Data
A ﬁreproof door in a single-leaf design optionally with
wooden or steel door frame and wooden door leaf for
installation in LVT partitions with leastwise F30 requirement.
Fireprooﬁng:
T30 as per DIN 4102 in F30 / F90 LVT partition
Substructure:
The studs, beams and hinges are made of galvanised
steel tubes and are roll-formed or edged steel sheet proﬁled section elements.
Design options:
Door frames:
- wooden door frame
- steel door frame
Design of door leaf:
- Flush
- With rebate
- Full door
- Door with window for light
Soundprooﬁng:
up to 45 dB Rw,P as per DIN EN ISO 140-01
Static requirements:
max. partition height: 3 500 mm
Partition thicknesses:
100 and 125 mm (19 mm panelling)
100 mm (13 mm panelling)
Dimensions:
Clear height:
max. 2 200 mm
Clear width:
max. 1 150 mm
Panel widths:
50 / 65 mm (wooden door frame)
45 / 60 mm (steel door frame)
Multiple functions:
- Smoke control as per DIN 18 095
- Air-conditioning category to III as per DIN EN 79
Subject to technical changes also without notiﬁcation.
F33
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
Doors
T30/RS Door Element in F90 LVT Partition
Steel Door Frame with Steel Door Leaf
Fig. 88
System description
Door element possible with ﬁre protection and smoke protection, single leaf, with steel door frame and steel door
leaf for installation into LVT partition with appropriate ﬁre
protection requirements. The door leaf is manufactured
as butt-jointed type.
Substructure:
The studs, beams and hinges are made of galvanised
and roll-formed or folded steel sheet proﬁled section elements.
Technical Data
Fireprooﬁng:
T30 as per DIN 4102 in F90 LVT partition
Smoke protection (as per DIN 18095):
T0 as per DIN 4102 in F30 LVT partition d ≥ 100 mm
T30 as per DIN 4102 in F90 LVT partition
Static requirements:
Max. partition height: 3 500 mm
Partition thicknesses:
100 and 125 mm (19 mm panelling)
89 and 100 mm (13 mm panelling)
Dimensions:
Inside frame size
min. ZFM b x h = 670 x 1 710 mm
max. ZFM b x h = 1 020 x 2 110 mm
Panel widths
55/40 mm (standard)
60/45 mm (with electric door opener)
Subject to technical changes also without notiﬁcation.
F34
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
Installation System for Partition Systems
Gira ITS 30
The installation system Gira ITS 30 provides an installation with great ﬂexibility and functionality in commercial
buildings.
Fig. 90
Gira ITS 30 brings different functions and devices of electrical installation, bus technology or name plates together,
in one busbar:
It is integrated in a 30-mm wide joint between the studs
of the partition system. The joint serves as space for the
installation of power supply lines and control lines, which
come out of the ceiling or out of the ﬂoor.
This system is also integrated in an LVT aluminium door
frame. The combination Gira ITS 30 in LVT aluminium
door frame with a visible width of 35 mm has been developed especially for glazing systems to hold the small look
of the system.
For the installation of elements of building services, the
busbar has three ﬁxed installation ranges in dif-ferent
heights: 300 mm. 1050 mm and 1500 mm.
Fig. 91
Moreover name plates of the guidance system COM.form
of Mabeg company can be installed on any height of the
busbar.
Gira ITS 30 is suited for installation in front of glass: The
small busbar and LVT aluminium door frame replace the
aluminium blind next to the door frame or between glazings and increase the quantity of glass. This leads to more
transparency in the building.
Fig. 89
Fig. 92
Subject to technical changes also without notiﬁcation.
F35
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
Accessories
Blinds for Glazing Systems
Fig. 93
All Lindner glazing systems can be combined with commercially available blinds for indoors. This makes the
extensive range of products from various manufacturers
available to you along with a wide variety of options.
Field of application:
Blinds to provide both shade and privacy in indoor areas.
These can be fastened on the frame outside the pane
(e.g. with non-bearing frames) or even inside the glazing
element (e.g. in double glazing).
Operation:
- Electric motor
- Cord / Reversing motor
- Cord / Rod
- Chain
- Crank
- Knob
Upper rail:
Roll-formed, coated steel channel section, 25 x 24 mm;
option: extruded, powder-coated circular proﬁled section,
D = 40 mm
Slats:
Aluminium band, 16, 25 or 35 mm wide, special alloyed,
highly ﬂexible, slightly curved; option: partially perforated
Lower rail:
Extruded aluminium proﬁled section element, 18 x 12, 27
x 12 or 35 x 12 mm, depending on width of slats, powdercoated according to RAL.
Guide cord and pull-up cord:
Made of long-lasting, high-strength polyester.
Side guides:
Available on request made of polyamide-sheathed steel
wire strands
Structural limits:
Min. width: 340 mm
Max width: 2 500 mm
Min. height: 2 500 mm
Max area: 4.0 m²
Options:
Vertical blinds with 63-mm wide slats
Overall height: up to 3 000 mm
Subject to technical changes also without notiﬁcation.
F36
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
Accessories
Blinds inside thermopane glazing
Fig. 94
Field of application:
Blinds to provide both shade and privacy in indoor areas.
These are built hermetically into the insulating glass and
thus are protected against soiling and damage from without, and take less space.
Operation:
- Electric motor
- Pull cord
- Crank
Upper rail:
Upper roller box made of extruded aluminium, stoveenamelled
Slats:
Aluminium slats, with priming coat and ﬁnishing coat of
enamel, 15 mm wide, slightly curved.
The slats are available in various colours, aluminium-plated and reﬂective.
Pull-up cord:
Pull cord made of textile cord with edge guard, UV-radiation guard and scalelike sheath to protect against sunlight.
Side guides:
Guide cords made of Terylene with UV-radiation guard
Structure of the panes:
Insulating glass is possible with various thicknesses and
combinations of: mirror glass, laminated safety glass,
tempered safety glass, casting-resin glass, ornamental
glass and heat protection glass.
Structural limits:
Min. width: 400 mm
Min. height: 300 mm
Max width: 2 200 mm
Max. height: 3 800 mm
Subject to technical changes also without notiﬁcation.
F37
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
Accessories
Tapered Façade Connection
Fig. 95
System description
Technical Data
Tapered façade connection in various designs make it
possible to connect to exterior façades using slim supports for LVT partitions.
Fireprooﬁng:
up to F90 is possible.
Substructure:
This consists of folded and roll-formed steel sheet proﬁled
section elements, galvanised or coated.
Design options:
- either matching partitions or
- fully-glazed
Field of application:
Connection of LVT partition systems to exterior façades
using slim supports.
Soundprooﬁng:
up to 51 dB Rw,P as per DIN EN ISO 140-03
With visible width of 241 mm and wall thickness of 43 mm;
F0 ﬁreprooﬁng
Measurement for the tapered façade connection only
Dimensions:
Variable, but limited for ﬁreproof and soundproof variations
Surfaces:
- Chipboard
- Metal
- Aluminium
- Plasterboard
Subject to technical changes also without notiﬁcation.
F38
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
Great Ways to Organise Your Ofﬁce
Hook-on Items and Ofﬁce Accessories
Here are a few examples showing the possibilities opened
up by Lindner ofﬁce and partition systems.
Fig. 101
There are various furnishings, examples of crosswise
organisation, ﬁling systems and hook-on cabinets, all
geared to our system as shown.
Surface of the hook-on elements:
Anthracite
Fig. 96
A4-Tray, crosswise
Fig. 102
Fig. 97
A4-Tray, lenghtwise
Fig. 98
Desk set
Fig. 103
Fig. 99
File board
Fig. 100
Picture hook
(stainless steel)
Subject to technical changes also without notiﬁcation.
F39
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
LVT Partition for Inspection Chambers F30
LM 500
Fig. 104
System description
Technical Data
A completely removable partition for inspection chambers,
which depends on the technique of removable partitions. It
serves as an alternative to conventional inspection chambers of dry mortarless construction, which have to be
equipped with expensive ﬂap lids or ﬁre protection doors.
Fireprooﬁng:
F30 as per DIN 4102
Substructure:
Consisting of folded and roll-formed steel sheet proﬁled
section elements, galvanised or coated.
Panelling:
Sandwich element system with hook-on system and metal panels
Joints and connections:
Joint sealant:
Plastic proﬁles are used on the ﬂoor and ceiling channels
and on stud proﬁle elements.
Connections:
Recessed ﬂoor, ceiling and wall junctions
Static requirements:
Non-supporting partition as per DIN 4103
Height up to max. 3 000 mm
Axial width up to max. 1 625 mm
Weight:
45 kg/m²
Joint width:
Vertical: 4 – 8 mm (Standard)
Horizontal: 4 – 15 mm
Partition thickness:
Approx. 90 mm
Special features:
- completely removable
- inspection-friendly handling for later installations
- easy dismantlement and reassembly
Subject to technical changes also without notiﬁcation.
F40
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
Instructions for Ordering, Installation and Use
Storage & Transport Instructions
- Load and unload delivery units with a forklift or crane
(lifting capacity of at least 1.5 t).
Fig. 105 A delivery unit of wall panels
- Transport inside the building using pallet lifts.
- Any interim storage should be in temperature-controlled
rooms which are protected against the weather.
- In cases of storage lasting for long periods of time, cover
the stacks of panels to avoid soiling.
- Avoid fast heating up or cooling down of storage rooms.
- Protect the corners of the panels against getting damaged.
Climatic Conditions for LVT Wall Panels
It is necessary to comply with the humidity restrictions to
assure the dimensional and geometrical accuracy of the
LVT partitions.
Fig. 106
Max. humidity in the air in g/m³
Like all materials used in construction, plasterboard panels, which are glued onto the reverse side of LVT wall
panels, are subject to linear expansion when affected by
temperature or moisture.
25
20
15
ted
mit
10
er
ep
ng
Ra
80 %
5
40 %
0
0
5
10
15
20
25
30
Air temperature in °C
Subject to technical changes also without notiﬁcation.
F41
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
Instructions for Ordering, Installation and Use
Installation Instructions
Fasten the ﬂoor and ceiling tracks (1) & (2) to the local
conditions, putting ceiling tape (3) in between and stick on
the system seals (4).
Screw the suspension brackets (9) into this regular grid
with the special screws (10). Joint widths of 0-12 mm can
be selected over the clearance of the drilled holes (11).
Fig. 107
The nib (12) is an aid for insertion when hooking on the
panelling.
Fig. 108
3
8
2
9
11
.
10
64
1
4
12
Adjust the main item of the system, the LVT stud (5) in the
tracks mentioned above using a height-adjustment bracket (6) and align the axial dimension and height. Draw the
joint seal (7) into the groove in the stud.
Finally, hook the wall panels provided with the suspension
brackets into one side of the post-and-beam structure. After putting the insulation material in, hook on the other
side of the partition.
Fig. 109
5
7
Note:
To hook on the wall panels, it is necessary to lift them.
Horizontal joints should therefore be planned with a joint
width of at least 12 mm in case the wall panel beneath
has to be removed.
6
The prefabricated wall panels are provided with regular
drillings on the reverse side of the panels. Clearance =
64 mm (8).
min. of 12 mm
Fig. 110
Wall panel or
glazing frame
Wall panel
Subject to technical changes also without notiﬁcation.
F42
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
Standards and Regulations
Table of Standards
Standard
Designation
Issued
DIN 4102
Behaviour in ﬁre of building materials & building components
Sep 1977
DIN 4103
Non-load bearing interior partition
Jul 1984
DIN 4109
Soundprooﬁng in building construction
Nov 1989
DIN 1249
Plate glass in the building trade
Feb 1980
DIN EN ISO 12 543
Glass in the building trade
Aug 1998
DIN 18 165
Fibrous insulating materials for the building industry
Mar 1987
DIN 18 202
Tolerances in building construction
Apr 1997
DIN 18 361
Glazing work
Oct 1979
DIN 18 257
Safety door signs
Mar 1991
DIN 68 100
Tolerance system for woodworking
Dec 1984
ETAG 002
Guideline for the European Technical Certiﬁcation
for Glued Glass Constructions
Jul 1998
System-speciﬁc Properties
- Consultancy, supervision of the real estate, and installation should all be carried out by specially trained qualiﬁed personnel
- It is also possible to rearrange this partition at any time
after installation (e.g. exchanging a full element for a
glazed element).
- The system has a sandwich-type construction.
- Linear or grid construction (preferred axial measurements: 800-1000 mm)
- Uniform partitions thickness (standard: 100 mm)
- Standard design up to a height of 3 200 mm
- Rw,p soundprooﬁng rating up to 54 dB
- Fireprooﬁng: - F30-design
- F30-glazing
- F90-design
- G30-glazing
- G90-glazing
- T30-door element, single-leaf
- Types of glazing: - Double glazing
- Glazing ﬂush with surface
- Single glazing, outside and centre
- Insulation glazing, centre
- It is possible to install cables and lines inside these partitions, both horizontally and vertically.
- Later installations can be carried out at any time (by removing one element of the wall panel).
- Surface options: Melamine resin coating
Laminated sheet
Real wood veneer
Metal
Plasterboard
- Recessed ﬂoor and ceiling connection in the standard
design
- Subsequent deliveries are possible of elements of the
same design as in the initial equipping.
Subject to technical changes also without notiﬁcation.
F43
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
Standards and Regulations
Static requirements
Excerpt from DIN 4103 - Non-load bearing interior partitions (July 1984)
Installation Area Types
Static Loads
Installation Area Type 1:
- For low numbers of people
- Examples: Flats, hotel rooms, ofﬁces, hospital rooms
and other rooms used similarly, including their corridors
Bending limit for load-bearing capacity of the partitions compared with static loading
- Acting horizontal linear load (working load), primarily
static, with points of application 0.9 m above the base of
the partition (Fig. 1).
Installation Area Type 1:
p1 = 0,5 kN/m
Installation Area Type 2:
p2 = 1,0 kN/m
- Light loading by brackets:
Installation Area Type 2:
- For high numbers of people
- Examples: Assembly rooms, classrooms, auditoriums, exhibition and sales rooms and other rooms used similarly
- Partitions between rooms with a difference in the height
of the ﬂoors ≥ 1.0 m
Vertical linear load of 0.4 kN/m (Fig. 2)
Resistance of the partitions against impact-like loading (Fig. 3)
Proof:
- Impact of a human body (soft impact)
- Sack of glass beads weighing 50 kg
- Damage to the partition is allowed, but the following conditions have to be met:
The partitions must be pulled out of their fastenings.
Partition elements that might seriously injure people
must not fall off.
The entire thickness of the partitions must not be punctured.
General requirements
Partitions have to:
- Resist static (primarily static) and impact loads, as might
occur when they are used
- Be able to assume loads applied to their surface in addition to their own weight, including any plaster or other
possible facing, and transfer such to other supporting
constructional elements, such as walls and ceilings.
- Transfer light loading by brackets
- In cases of loading by wind power, such as in industrial
buildings with large doors frequently open (supporting
documents 4.2-4.4 of DIN 4103), keep a supporting document for half the dynamic pressure as per DIN 1055,
Part 4.
Partitions can:
- Assume functions for securing against crashing
Working load (primarily static) -Fig. 1
Loading by brackets - Fig. 2
Impact-like loading - Fig. 3
£ 300
1650
0.4 kN/m
(= 40 kg/m)
Wall length
Room heigt
50
k
g
=
£ 300
Room heigt
Installation Area
Type 2
(Large numbers
of people)
1.0 kN/m
(= 100 kg/m)
Pressure
50 kg
0.5 kN (= 50 kg)
=
900
Horizonal
linear loadt
Room heigt
Traction
Installation Area
Type 1
(Low numbers
of people)
0.5 kN/m
(= 50 kg/m)
Subject to technical changes also without notiﬁcation.
F44
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
GDL – IGG Fully-Glazed Partition
System LW600
Fig. 111
Subject to technical changes also without notiﬁcation.
F45
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
GDL – IGG Fully-Glazed Partition
System LW600
Fig. 112
System description
A fully-glazed partition ﬂush with surfaces, in which the
proﬁled section elements are integrated between two
panes so as not to be visible, without any projecting or
visible parts on the surface of the glass. Clamping of the
edges of the glass in a connection at the margins makes
the technology completely disappear visibly. This full glazing is constructed in row assemblies.
Substructure:
The substructure, including the glass retaining frame, is
made of anodised aluminium.
Glazing:
Thermopane glazing, 2 x 6 mm tempered safety glass
(standard)
Field of application:
Ofﬁce and corridor partitions
with automatic and manual stop doors and swinging
doors.
prepared for a shelving system
Door Closer:
Swinging doors with ﬂoor closer
Stop door with top door closer
Both designs can also be combined with automatic system for opening and/or closing.
Technical Data
Fireprooﬁng:
F0
Partition thickness:
39 mm
Soundprooﬁng:
35 dB Rw,P as per DIN 4109
Weight:
Fixed panel elements:
2 x 6 mm tempered safety glass = 34 kg/m²
2 x 8 mm tempered safety glass = 44 kg/m²
Stop doors and swinging doors:
Thickness of door leaf: approx. 40 mm
Max. weight of door leaf: 120 kg per door leaf
Static requirements:
Installation area type 1, non-load bearing partition as
per DIN 4103 for the dimensions w x h = max 1250 x
2800 mm
Subject to technical changes also without notiﬁcation.
F46
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
GDL – IGG Fully-Glazed Partition
Fig. 113 Vertical section of ceiling connection
Fig. 114 Horizontal section of linear modular system
Fig. 115 Vertical section of ﬂoor connection
Fig. 116 Horizontal section of wall connection
Fig. 117 Horizontal section of door frame
Fig. 118 Vertical section of door frame with door closer
on the top side
Subject to technical changes also without notiﬁcation.
F47
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
Fully-Glazed Partitions
Lindner Fully-Glazed Partition
System LW620
Fig. 119
Subject to technical changes also without notiﬁcation.
F48
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
Fully-Glazed Partitions
Lindner Fully-Glazed Partition
System LW620
Fig. 120
System description
Technical Data
A fully-glazed partition without any vertical supporting
members – only horizontal fastening tracks on the ﬂoor
and ceiling.
Fireprooﬁng:
F0
Substructure:
Aluminium
Field of application:
Corridor partitions with manual sliding doors which are
moveable in front of the partition or revolving doors with
inﬁll strips on both sides.
Element connection:
Silicon
Dry silicon
T-section
Soundprooﬁng:
Depends on the design option
Partition height:
Up to max. 2 800 mm
Glass thicknesses:
10 and 12 mm for tempered safety glass
Weight:
Sliding door:
Max weight of leaf: 100 kg
Subject to technical changes also without notiﬁcation.
F49
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
Fully-Glazed Partitions
Lindner Fully-Glazed Partition
Fig. 121 Vertical section of ceiling connection
with sliding door
Fig. 122 Horizontal section of glazing next to glazing
Fig. 123 Horizontal section of ceiling connection
with sliding door
Fig. 124 Horizontal section of wall connection
Fig. 125 Vertical section of aluminium door frame
Fig. 126 Horizontal section of aluminium door frame
with post cap element
Subject to technical changes also without notiﬁcation.
F50
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
Timber Framework Partition
System LW640
Fig. 127
Fig. 128
Subject to technical changes also without notiﬁcation.
F51
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
Timber Framework Partition
System LW640
Fig. 129
System description:
Technical Data
A partition with a timber framework method of construction for interior areas. This partition is delivered with prefabricated elements. The individual elements can later be
exchanged without removing the adjacent elements.
Fireprooﬁng:
F0
Substructure:
This is made of derived timber products.
Panelling:
Wall Shell:
Frame:
Surface:
Glazing:
16 mm, MDF
38 mm, MDF
Any type of wood desired
mono glass pane
Connections:
Recessed ﬂoor, ceiling and wall connections
Design options:
Solid partition
fully-glazed partition
Special features:
- Inspection-friendly handling for later installations due to
wall shells being removable on one side
- Replacement of individual elements
Soundprooﬁng:
Depends on the design option
Static requirements:
Installation area type 1 and 2
Non-supporting partitions as per DIN 4103
Height: 2 700 mm
Axial width: 1 250 mm
for fully-glazed partitions with laminated safety glass
12 mm
Weight:
34 – 38 kg/m² for solid partitions
20 – 35 kg/m² for fully-glazed partitions
Joint width:
15 mm
Partition thicknesses:
100 mm
Field of application:
Ofﬁces
Subject to technical changes also without notiﬁcation.
F52
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
Timber Framework Partition
Fig. 130 Vertical section of solid partition
Fig. 131 Vertical section of glass partition
Fig. 132 Horizontal section of linear modular system of
solid partition
Fig. 133 Horizontal section of linear modular system of
glazing
Subject to technical changes also without notiﬁcation.
F53
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
Timber Framework Partition
Fig. 134 Horizontal section of wall connection on solid
partition
Fig. 135 Vertical section of door frame
Fig. 136 Horizontal section of wall connection on
glazing
Fig. 137 Horizontal section of solid partition next to
glazing
Fig. 138 Horizontal section of door frame
Subject to technical changes also without notiﬁcation.
F54
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
Fully-Glazed Partition
System LW650
Fig. 139
Subject to technical changes also without notiﬁcation.
F55
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
Fully-Glazed Partition
System LW650
Fig. 140
System description
Fully-glazed partition, ﬂush double glazing. The glass
panes are installed to the vertical system stud (with glass
holding elements on the side).
Substructure:
Consisting of aluminium proﬁles.
The glass holding elements are made of stainless steel.
Door elements:
Offset hung door element in rebated frame (with door
frame 35/35 mm) and a glazed door leaf (10 mm) with
bearing.
Field of application:
Ofﬁce partitions and corridor partitions
Technical Data
Fireprooﬁng:
F0
Soundprooﬁng:
According to type
Static requirements:
Installation area 1
Non-load bearing partition as per DIN 4103
Height up to max. of 3,300 mm
Axial width up to max. of 1,500 mm
Weight:
35 – 40 kg/m²
Joint width:
10 mm
Partition thickness:
90 mm
Subject to technical changes also without notiﬁcation.
F56
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
Fully-Glazed Partition
Fig. 141 Vertical section of glass wall
Fig. 142 Vertical section of door element
Fig. 143 Horizontal section of linear modular system
Fig. 144 Horizontal section of door element
Subject to technical changes also without notiﬁcation.
F57
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
Lindner Safelite SL90
System LW660 F90
Fig. 145
Subject to technical changes also without notiﬁcation.
F58
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
Lindner Safelite SL90
System LW660 F90
Fig. 146
NEU
System description
Technical Data
Lindner Safelite SL90 is a kit for the construction of ﬁreresistant glazings. The studs consist of special light metal
proﬁles, which are glazed with ﬁre- resistant panes.
Thermal insulators serve as glass supporting bars and
are covered with aluminium border bars. Visible width of
the proﬁles is 70 mm.
Its time- saving construction simpliﬁes the handling and
installation.
Fireprooﬁng:
F90 as per DIN 4102
Substructure:
Aluminium
Design options:
Fully glazed partition
with transversal division
Field of application:
Corridor- and room partitions
Soundprooﬁng:
49 dB Rw,P as per DIN EN ISO 140-03
airbone sound insulation of glass pane
Static requirements:
installation area 1 and 2
non- supporting partition as per DIN 4103
heigth up to 4 000 mm
axial width up to 1 435 mm
Clear dimension b x h max. 1 365 x 2 165 mm
Single panes applicable in landescape format
Weight:
67 kg/m² weigth of glass pane
Partition thickness:
121 mm
Glass thickness:
45 mm
Subject to technical changes also without notiﬁcation.
F59
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
Lindner Safelite SL90
Fig. 147 Vertical section of glazing with cross division
Fig. 148 Horizontal section of linear modular system
Fig. 149 Horizontal section of wall connection
Subject to technical changes also without notiﬁcation.
F60
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
Team Panel
System LW670
Fig. 150
Fig. 151
Fig. 152
Subject to technical changes also without notiﬁcation.
F61
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
Team Panel
System LW670
Fig. 153
NEU
System description
Technical Data
Movable wall as a nonocoque construction, which can be
installed between the storey ceilings without damaging
the building. This system guarantees a great ﬂexibility in
dismantling and reassembling because of the fact that no
dowelled joint is necessary.
The studs consist of aluminium circular tubes, which are
as high as the room. On the bottom and at the ceiling
there are discs which are able to absorb the deﬂection of
the ceiling.
The installation of the panels depends on the height of the
parapet and the height of the room. The panels are also
available as sound-absorbent panels.
Sound absorption:
Itemisation for punched metal panel:
Acoustical absorbance according to ISO 11 654
αw = 0,90 with an perforation rate ≥ 30 %
Substructure:
Consisting of folded steel sheet proﬁled section elements,
galvanised or coated and aluminium circular tubes.
Panelling:
The panels are available for vertical or horizontal division.
The surface of the panels can be real wood veneer, melamine resin, laminated plastic or metal.
Options: covered with textile to use it as a pin board, cork
linoleum, punched or slotted sound- absorbing panel.
Field of application:
Movable wall
Room division
Wall cladding
Other surfaces, hole patterns and perforation rates are
possible, as well as panelling with other products of manufacturers who produce sound absorbing wood panels.
Excellent acoustical absorption in low- and medium-frequency ranges at a thickness of void of only 30 mm.
Static requirements:
For movable walls certiﬁcates according to DIN 4103
are necessary. But its impact load at a room height of
3 250 mm has been tested.
Weight: 35 kg/m²
Joint width: 10 mm
Partition thickness: 110 mm
Customized solutions are possible on request!
Subject to technical changes also without notiﬁcation.
F62
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
Team Panel
Fig. 154 Vertical section
Fig. 155 Horizontal section of linear modular system
Fig. 156 Horizontal section of stop end
Subject to technical changes also without notiﬁcation.
F63
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
Plasterboard Partition
Built-in Components in Plasterboard Partitions
Fig. 157
Lindner is one of the largest end-users of plasterboard products.
Lindner also works with external brands on request in addition to its own wide range of products such as:
- F30 Glazing
- G30 Glazing
- G90 Glazing
- F0 and F90 Access panels
- Façade sword
Subject to technical changes also without notiﬁcation.
F64
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
Plasterboard Partition
Lindner Akusto-Wand
System description
Fig. 158
With Lindner’s innovative Akusto studs,
partitions can achieve a sound insulation
to 54 dB – with conventional plasterboard
soundprooﬁng is achieved irrespective of
boards’ manufacturer.
plasterboard
value of up
panels. This
the plaster-
With the Akusto stud it is possible to construct partitions
from a thickness of 75 mm while at the same time building
higher than described in DIN 18 183 without reducing the
standard axial measurement of 625 mm.
For ﬁreprooﬁng, all commonly used systems can be executed with Akusto studs instead of CW-proﬁled section
elements.
Substructure
This is made of folded or roll-formed steel sheet proﬁled
section elements and is galvanised. The post-and-beam
proﬁled section element is acoustically decoupled.
Wall cladding
The "Lindner Akusto" wall panel with double-layer
panelling (Fireproofing and soundproof not allowed for)
Width of section in mm
Partition height in mm EB1 £ 3600
Partition height in mm EB2
75
100
£ 4500
£ 5500
£ 4500
£ 5500
50
–
Installation
Electrical installations can also be placed horizontally due
to removable panels in the post-and-beam proﬁled section elements.
Soundprooﬁng „Lindner Akusto“ single-stud partition, with double-layer panelling
Description
System
D
Section
h
mm
100
125
150
150
mm
50
75
100
100
LGK 2.100.49
LGK 2.125.52
LGK 2.150.52
LGK 2.150.54
Official supporting documents
sound
static EB1/2
fire *
ITA/LSW
x
x
x
x
LGA
h £ 5300
h £ 6400
h £ 7000
h £ 7000
MPA BS
EB1 £ 4000
EB1 £ 5500
EB1 £ 6500
EB1 £ 6500
Thickness of Soundproofing
DIN4109
insulation layer plasterboard Bbl.1/A1: 2003-9
panel > 8,5 kg
Rw, R [dB]
Rw, R [dB]
mm
40
49
45
60
52
49
40
52
47
54
80
50
* EB2 on request
Fire
ratings
Panelling
Insulation layer
Type
Thickness Apparent density Thickness
"Lindner Akusto" single-stud partition, with single-layer panelling
F30 A
GKF
12.5
30
40
"Lindner Akusto" single-stud partition, with double-layer panelling
F30 A
F60 A
GKB
2 x 12.5
2 x 12.5
F90 A
GKF
F120 A
15 + 12.5
2 x 18
2 x 15
3 x 12.5
F180 A
25 + 12.5
30
40
40
30
50
100
40
40
50
100
50
100
50
100
40
80
60
40
40
40
80
60
80
60
80
60
Type
Mineral wool insulating material,
Building-Materials Class A
d ³ 13 kg/m³ as per Inspection Certificate 4201/T2)
for fireproofing or DIN 41024
Fireprooﬁng
Axial clearance
a [cm]
Supporting
document
62.5
DIN 4102-4
and/or
015/01 Mer
3142/9181
62.5
DIN 41024and/or
015/01 Mer
3142/9181
Subject to technical changes also without notiﬁcation.
F65
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
Lindner Fire Wall
System LGK-530-BW
Fig. 159
System description
Technical Data
Thinnest ﬁre wall of dry and mortaless construction with
Lindner-Akusto-studs. High sound insulation values can
be achieved by a special way of construction and an additional steel sheet inlay.
Fireprooﬁng:
Fire wall F90 as per DIN 4102
Partition F120 as per DIN 4102
Substructure
Consisting of folded steel sheet proﬁled section elements,
galvanised. The stud proﬁle is installed in a special soundinsulating way.
Static requirements:
Installation area 1 and 2
Non- supporting partition as per DIN 4103
max. partition height 4 000 mm
Partition thickness:
105 mm
Subject to technical changes also without notiﬁcation.
F66
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
G30 Steel Frame Glazing in Plasterboard Partitions
System LGK-100-G30
Fig. 160
System description
Technical Data
Plasterboard glazing with steel framing and 50-mm visible
width at the perimeter.
This glazing can be carried out either with single or double glazing.
Fireprooﬁng:
G30 as per DIN 4102 in plasterboard partitions for F30
Substructure:
The ﬂoor and ceiling tracks and cross-section elements
are made of folded and galvanised steel sheet proﬁled
section elements.
The studs and frames are made of galvanised steel
tubes.
Design options:
Fanlight glazing
Soundprooﬁng:
41 dB Rw,P as per DIN 52210-03
Measurement of the glaszing system only
Static requirements:
Max. height: 3 500 mm
Partition thicknesses:
from 100 mm
with panelling thickness of 2 x 12.5 mm
Dimensions:
Clear height/width
970 mm x 1770 mm
whether vertical or horizontal format
Subject to technical changes also without notiﬁcation.
F67
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
G30 Steel Frame Glazing in Plasterboard Partitions
Fig. 161 Vertical section of glass wall to GK-wall
Fig. 162 Horizontal section of glazing next to glazing
Fig. 163 Vertical section of dado connection
Fig. 164 Horizontal section of glazing to GK-wall
Fig. 165 Horizontal section of wal connection
Fig. 166 Horizontal section of 90°-corner
Subject to technical changes also without notiﬁcation.
F68
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
G90 Steel Frame Glazing in Plasterboard Partitions
System LGK-110-G90
Fig. 167
System description
Technical Data
Plasterboard glazing with steel framing but with only one
visible vertical covering proﬁled section element with a
75-mm visible width.
This can also be replaced by a plasterboard strip on request. The glazing can be carried out with single- or double-glazing.
Fireprooﬁng:
G90 as per DIN 4102 in F90 plasterboard partitions
Substructure:
The ﬂoor and ceiling tracks and cross-section elements
are made of edged and galvanised steel sheet proﬁled
section elements. The studs and frames are made of galvanised steel pipes.
Design options:
Fanlight glazing
Soundprooﬁng:
This depends on the structure of the panes
Static requirements:
Max. height: 3 500 mm
Max. axial measurement: 2 075 mm
Partition thicknesses:
from 100 mm
with panelling thickness of 2 x 12.5 mm
Dimensions:
Clear height/width
Height of pane: max. 1 000 mm
Width of pane: max. 2 000 mm
Subject to technical changes also without notiﬁcation.
F69
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
G90 Steel Frame Glazing in Plasterboard Partitions
Fig. 168 Vertical section of GK-wall to glass wall
connection
Fig. 169 Horizontal section of wall connection
Fig. 170 Vertical section of dado connection
Fig. 171 Horizontal section of 90°-corner
Fig. 172 Horizontal section of glazing next to glazing
Fig. 173 Horizontal section of mono glazing
Subject to technical changes also without notiﬁcation.
F70
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
G30 / F30 Frameless Glazing in Plasterboard Partitions
System LGK-120-G30
System LGK-120-F30
Fig. 174 F30 plasterboard partition with wood veneered wall panels an G30 fanlight
Subject to technical changes also without notiﬁcation.
F71
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
G30 / F30 Frameless Glazing in Plasterboard Partitions
System LGK-120-G30
System LGK-120-F30
Fig. 175
System description
Technical Data
Frameless plasterboard glazing with only one vertical
covering proﬁled section element with a 50-mm visible
width. The glazing can be carried out with single- or double-glazing.
Fireprooﬁng:
G30 / F30 as per DIN 4102 in F30 plasterboard partitions
Substructure:
The ﬂoor and ceiling tracks and cross-section elements
are made of folded and galvanised steel sheet proﬁled
section elements.
The studs are made of galvanised steel tubes.
Design options:
Fanlight glazing
Dado glazing (only F30)
Soundprooﬁng:
45 dB Rw,P as per DIN EN ISO 140-03
Measurement of the glazing system
Static requirements:
Max. height: 4 500 mm
Max. axial measurement: 2 550 mm
Partition thicknesses:
from 100 mm
with panelling thickness of 2 x 12.5 mm
Dimensions:
Clear height/width
Height of pane: max. 1 200 mm
Width of pane: max. 2 500 mm
Customized solutions are possible on request!
Subject to technical changes also without notiﬁcation.
F72
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
G30 / F30 Frameless Glazing in Plasterboard Partitions
Fig. 176 Vertical section of fanlight glazing
Fig. 177 Vertical section of GK-wall to glass wall
connection
Fig. 178 Horizontal section of wall connection
Fig. 179 Horizontal section of linear modular system
Fig. 180 Horizontal section of GK-wall to glass wall
connection
Subject to technical changes also without notiﬁcation.
F73
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
G30 / F30 Frameless Glazing in Plasterboard Partitions
Fig. 181 Horizontal section
T-junction on linear modular system via
GKfacade connection
Fig. 182 Horizontal section of T-junction on module via
plaster board facade connection
Fig. 183 Horizontal section of 90°-corner
Fig. 184 Horizontal section of steel door frame
Subject to technical changes also without notiﬁcation.
F74
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
G30 High-performance Sound-Insulation Glazing
in Plasterboard Partitions
System LGK-140-G30
Fig. 185
System description
Technical Data
Plasterboard glazing in the form of a three-part element
with panes glued on, which ﬁt ﬂush with the plasterboard
partition.
The element can be carry out as ﬂush triple glazing with
clear glass.
Fireprooﬁng:
G30 as per DIN 4102 in F30 plasterboard partitions
Substructure:
The glazing frame is made of aluminium.
The studs and beams are made of galvanised steel
tubes.
Design options:
Fanlight glazing
Soundprooﬁng:
47 dB Rw,P as per DIN EN ISO 140-03
Measurement of the glazing system, d = 100 mm
Static requirements:
Max. height: 3 500 mm
Max. axial measurement: 2 500 mm
Partition thicknesses:
from 100 mm
with panelling thickness of 2 x 12.5 mm
Dimensions:
Height of element: max. 1 200 mm
Width of element: max. 2 500 mm
Customized solutions are possible on request!
Subject to technical changes also without notiﬁcation.
F75
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
G30 High-performance Sound-Insulation Glazing
in Plasterboard Partitions
Fig. 186 Vertical section of ceiling connection
Fig. 187 Vertical section of GK-wall to glass wall
connection
Fig. 188 Vertical section of glass wall connection
Fig. 189 Horizontal section of linear modular system
Subject to technical changes also without notiﬁcation.
F76
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
Façade Sword, High-performance Sound-Insulation
LGK-500-F0
Axis of
construction
Fig. 190
System description
Technical Data
With plasterboard partitions and removeable partitions,
the façade sword makes it possible to connect to exterior
façades by using slim supports. With a total thickness of
just ≥ 58 mm, soundprooﬁng is achieved of Rw,P ≥ 52 dB.
These elements are preassembled by the factory and are
delivered to the construction site ready to install, where
the top layer made of 15-mm GKF-panels is applied.
Fireprooﬁng:
F0
Substructure:
Channel framing section with metal panel permanently attached on one side. The metal panel on the opposite side
is ﬁxed in a decoupled way.
Field of application:
Connecting plasterboards or removable partitions to exterior façades with slim supports.
Soundprooﬁng:
As per DIN EN ISO 140-03
Rw,P up to 52 dB with a width of just 330 mm
Dimensions:
Thickness of element: 58 mm
Width of element: variable
Height of element: variable
Surface:
GKF panels
Other surfaces are available on request
Patented method
Subject to technical changes also without notiﬁcation.
F77
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
F90 Access Panel in Plasterboard Shaft Walls
or Solid Walls
LGK-510-F90
Fig. 192 Horizontal section
£2100
240
Fig. 191 Elevation
³480
240
£2100
£5000
Fig. 193 Vertical section
200
£1000
³528
£1000
300
Product Description
Technical Data
An access panel made of a tubular steel frame with plasterboard surface for installation in plasterboard shaft walls
or solid walls. The panel is ﬂush with the partition; only its
strap hinge projects above the overall level of the opening. A 10-mm joint is visible on the other sides.
Fireprooﬁng:
F90 as per DIN 4102
in F90 plasterboard shaft walls or solid walls
Substructure:
Outer frame made of galvanised tubular steel; the hinge
can be installed with a choice of galvanised steel or highgrade steel. The substructure for fastening the outer frame
is made of folded and galvanised steel sheet proﬁled section elements.
Design options:
Installation in F90 shaft walls with 2 x 25 mm plasterboard
panelling (such as Knauf W628) or solid walls; element
panelled with 2 x 25-mm GKF-panels, lock with square
entering catch (visible on the surface), also with door
handle, 2 access panels can be installed on top of one
another.
Static requirements:
Max. height: max. 5 000 mm
Partition thicknesses:
Plasterboard shaft walls
With panelling thickness of 2 x 25 mm plasterboard panels
Dimensions:
Clear height/width
Height: max. 2 100 mm
Width: max. 1 000 mm
Subject to technical changes also without notiﬁcation.
F78
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.
F0 Access Panel in Plasterboard Partitions
LGK-520-F0
Fig. 194 Elevation
Fig. 195 Horizontal section
Max. clearance = 1000
Max. clearance = 2000
10
4
Fig. 196 Vertical section
Product Description
Technical Data
An access panel made of an aluminium frame with plasterboard surface for installation in plasterboard partitions.
The panel is ﬂush with the partition; only its hinge projects
above the overall level of the opening. A 4-mm joint is
visible on the other sides. This inspection access panel
should only be used to close openings for installation and
inspection purposes without any special requirements.
Fireprooﬁng:
F0
Substructure:
Outer frame made of aluminium; the strap hinge can be
installed with a choice of galvanised steel or high-grade
steel. The substructure for fastening the outer frame is
made of folded and galvanised steel sheet proﬁled section elements.
Design options:
Access panel with only single-layer panelling with 12.5mm plasterboard panels; installation in partitions with single-layer or double-layer panelling; lock with square entering catch (visible on the surface) or with spring-loaded
latch; also with door handle.
Partition thicknesses:
Plasterboard partitions and shaft walls
with panelling thickness of 1 x or 2 x 12.5 mm
Dimensions:
Clear height/width
Height: max. 2 000 mm
Width: max. 1 000 mm
Only for access panel with single-layer panelling (12.5 mm)
Up to a clear dimension of 600/600 mm
4-mm joint at the perimeter with recessed hinge
Also access panel with double-layer panelling (2 x 12.5 mm)
Subject to technical changes also without notiﬁcation.
F79
15.0
Partitions
Be sure to see the latest version of this page on our website at: www.lindner-holding.de or www.lindner.ag
This document is the intellectual property of Lindner Holding KGaA Arnstorf.
Without our approval, it may not be either reproduced or commercialised, distributed or
presented to other individuals for commercial purposes without authorisation to do so.

Download Report