CAD Files can be obtained by clicking on the link in the table. Dynamic load capacity C Ball Linear screw module d x P Ball Fixed 0 Guideway screw bearing (N) (N) (N) Maximum permissable loads Dynamic moments Mt (Nm) ML (Nm) FV (N) FH (N) 24000 6000 Downloads LT=150 LT=220 TKK 15155 Al without 16 x 10 16 x 16 - - 9600 19500 7700 20 x 5 17000 1020 900 1580 DXF DWG Dimensions 14300 20 x 20 12200 LT=320 LT=450 without 20 x TKK 205 225 Al TKK 20- 20 x 20 25 x 225 St 5 25 x 10 - - 14300 64300 17000 12200 5100 4100 7400 79200 19800 15900 DXF(Al) DWG(Al) Dim's(Al) Dim's(St) 18800 15800 25 x 25 Al only 15100 LT=320 LT=450 without TKK 3032 x 325 Al 5 TKK 30325 St 32 x 10 32 x 20 - - 21500 100000 26200 26000 11500 9100 15600 123200 30800 22700 32 x 32 DXF(Al) DWG(Al) Dim's(Al) Dim's(St) 17800 LT=450 without 40 x TKK 355 455 Al 40 x 10 - - 29100 132500 50000 40 x 20 37800 40 x 40 35300 29000 EI values Linear module flat base high base EIX EIY IX (108 Ncm2 ) (108 Ncm2 ) (cm4 ) 62.17 - - 196.59 25.27 355.95 - - TKK 30-325 St TKK 35-455 Al 163200 40800 DXF DWG Dimensions Weight L=Length in mm mb=carriage flat base (kg) (kg) high base (kg) LT=150 LT=220 3.07 5.13 TKK 20-225 St 18100 Carriage mass IY (cm4 ) TKK 15-155 Al TKK 20-225 Al TKK 30-325 Al 19800 2.3 3 10.010xL+m -0.3 b 20.0124xL+m +2 b LT=320 LT=450 9.88 577.03 7 13 9 18 1 10.015xL+m -0.4 0.026xL+mb b 0.4 20.018xL+m +3 20.029xL+m +3 b b 10.040xL+m -0.4 b 20.043xL+m +3 b LT=320 LT=450 9.92 664.0 45.69 1156.91 17.27 1826.96 - - 34.71 2554.23 - - 17 23 33.5 45.4 10.029xL+m -1 10.048xL+m -1 b b 20.035xL+m +5 20.054xL+m +5 b b 10.070xL+m -1 b 20.076xL+m +5 b LT=450 41 10.056xL+m -2.5 b 20.066xL+m +12 b Notes: 1 = without drive (without ball screw drive and end plates) 2 = with drive (ball screw drive) E = modulus of elasticity (N/cm2) I = Second moment of area (cm4) LT = Carriage length (mm) Note on dynamic load capacities and moments The dynamic load capacities and moments are based on 100 000 m travel. However, a travel of just 50 000 m is often taken as a basis. If this is the case, for comparison purposes, multiply values C, Mt and ML from the table by 1.26. Load capacities for the precision ball screw assembly comply with DIN 69 051.
© Copyright 2024 ExpyDoc
