ECM-BYT Intel® Bay Trail Processors 3.5” Micro Module Quick Installation Guide 1st Ed – 21 March 2014 Part No. E2017392000R ECM-BYT Quick Installation Guide 1. Getting Started 1.1 Safety Precautions Warning! Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the power is on. Sensitive electronic components can be damaged by sudden power surges. Only experienced electronics personnel should open the PC chassis. Caution! Always ground yourself to remove any static charge before touching the CPU card. Modern electronic devices are very sensitive to static electric charges. As a safety precaution, use a grounding wrist strap at all times. Place all electronic components in a static-dissipative surface or static-shielded bag when they are not in the chassis. 1.2 Packing List Before you begin installing your single board, please make sure that the following materials have been shipped: 1 x 3.5” ECM-BYT Micro Module 1 x Quick Installation Guide for ECM-BYT 1 x AUX-032 daughter board W/Audio/4USB 1 x DVD-ROM contains the followings: — User’s Manual (this manual in PDF file) — Ethernet driver and utilities — VGA drivers and utilities — Audio drivers and utilities 1 x Cable set contains the followings: — 1 x Audio cable (12pin,2.0 pitch) — 1 x USB 2.0 cable (10P/2.0mm-10P/2.54mm) — 1 x Serial ATA cable (7-pin, standard) — 1 x Wire SATA power cable (15-pin,2P/2.0mm) — 1 x Flat cable 9P(M)-PHD 10P/2.0mm) 3M foam (VHB-4622 10mm*20mm*1.1mm) 2 ECM-BYT Quick Installation Guide ECM-BYT Quick Installation Guide 2. Hardware Configuration ECM-BYT Quick Installation Guide 3 ECM-BYT Quick Installation Guide 2.1 Product Overview 4 ECM-BYT Quick Installation Guide ECM-BYT Quick Installation Guide ECM-BYT Quick Installation Guide 5 ECM-BYT Quick Installation Guide 2.2 Jumper and Connector List You can configure your board to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2, and 3. In this case, you would connect either two pins. The jumper settings are schematically depicted in this manual as follows: A pair of needle-nose pliers may be helpful when working with jumpers. Connectors on the board are linked to external devices such as hard disk drives, a keyboard, or floppy drives. In addition, the board has a number of jumpers that allow you to configure your system to suit your application. If you have any doubts about the best hardware configuration for your application, contact your local distributor or sales representative before you make any changes. The following tables list the function of each of the board’s jumpers and connectors. Jumpers Label Function Note JBAT1 Clear CMOS 3 x 1 header, pitch 2.00 mm JRI1 COM 1 pin 9 signal select 3 x 2 header, pitch 2.00 mm JAT1 AT/ ATX Input power select 3 x 1 header, pitch 2.00 mm JBKL_SEL1 LCD backlight brightness adjustment 3 x 1 header, pitch 2.00 mm JTOUCH_SEL1 Touch connector select jumper 3 x 1 header, pitch 2.00 mm Label Function Note BT1 Battery connector 2 x 1 wafer, pitch 1.25 mm CPU_FAN1 CPU fan connector 4 x 1 wafer, pitch 2.54 mm HDMI1 HDMI connector Connectors 6 ECM-BYT Quick Installation Guide ECM-BYT Quick Installation Guide JAUDIO1 Audio connector 6 x 2 header, pitch 2.00 mm JBKL1 LCD inverter connector 5 x 1 wafer, pitch 2.00 mm COM1 Serial port 1 connector D-sub 9-pin, male COM2/3/4 Serial port 2/3/4 connector 5 x 2 header, pitch 2.00 mm JDIO1 General purpose I/O connector 6 x 2 header, pitch 2.00 mm JFP1 Miscellaneous setting connector 5 x 2 header, pitch 2.00 mm JLPC1 Low pin count interface 5 x 2 header, pitch 2.00 mm JLVDS1 LVDS connector 20 x 2 header, pitch 1.25 mm JTOUCH1 Touch connector 5 x 1 header, pitch 2.00 mm USB1_2 On-board connector for USB2.0 x 1 On-board connector for USB3.0 x 1 JUSB3_4 On-board header for USB2.0 5 x 2 header, pitch 2.00 mm H_JUSB12 On-board header for USB2.0 5 x 2 header, pitch 2.00 mm JEC_ROM1 EC Debug connector 3 x 1 header, pitch 2.00 mm LAN1 RJ-45 Ethernet connector LED1 LED connector PWR_SB1 5VSB connector in ATX 3 x 1 wafer, pitch 2.54 mm PWR1 Power connector 2 x 2 wafer, pitch 4.20 mm JKBMS1 PS/2 keyboard & mouse connector 3 x 2 header, pitch 2.00 mm SATA_PWR1 SATA power connector 2 x 1 wafer, pitch 2.00 mm SATA1 Serial ATA connector 1 VGA1 VGA connector D-sub 15-pin, female BIOS_SPI1 BIOS SPI connector 4 x 2 header, pitch 2.00 mm M_PCIE1 Mini-PCI connector SO_DIMM1 DDR3 SODIMM connector CF1 CF card slot ECM-BYT Quick Installation Guide 7 ECM-BYT Quick Installation Guide 2.3 Setting Jumpers & Connectors 2.3.1 Clear CMOS (JBAT1) Protect* Clear CMOS * Default 2.3.2 COM 1 pin 9 signal select (JRI1) +5V Ring* +12V * Default 8 ECM-BYT Quick Installation Guide ECM-BYT Quick Installation Guide 2.3.3 AT/ ATX Input power select (JAT1) AT* ATX * Default 2.3.4 LCD backlight brightness adjustment (JBKL_SEL1) PWM Mode* DC Mode * Default ECM-BYT Quick Installation Guide 9 ECM-BYT Quick Installation Guide 2.3.5 Touch connector select jumper (JTOUCH_SEL1) 5W* 4W * Default 2.3.6 Touch connector (JTOUCH1) 10 ECM-BYT Quick Installation Guide JTOUCH1 4-Wire 5-Wire 1 TOP UL 2 Bottom UR 3 NA Sense 4 Right LR 5 Left LL ECM-BYT Quick Installation Guide 2.3.7 5VSB connector in ATX (PWR_SB1) Signal PIN PSON_ATX# 1 GND 2 +ATX5VSB 3 2.3.8 Battery connector (BT1) Signal PIN GND 2 +3.3V 1 ECM-BYT Quick Installation Guide 11 ECM-BYT Quick Installation Guide 2.3.9 CPU fan connector (CPU_FAN1) Signal PIN GND 1 +12V 2 EC_TACH0 3 FAN_PWM0 4 2.3.10 LCD inverter connector (JBKL1) Signal PIN +5V 5 VBRIGHT 4 BKLEN 3 GND 2 +12V 1 2.3.10.1 Signal Description – LCD Inverter Connector (JBKL1) Signal Signal Description VBRIGHT Vadj = 0.75V ~ 4.25V (Recommended: 4.7KΩ, >1/16W) BKLEN LCD backlight ON/OFF control signal 12 ECM-BYT Quick Installation Guide ECM-BYT Quick Installation Guide 2.3.11 PS/2 keyboard & mouse connector (JKBMS1) Signal PIN PIN Signal KBDT 1 2 KBCK GND 3 4 KBVCC MSDT 5 6 MSCK 2.3.12 On-board header for USB2.0 (JUSB3_4) Signal PIN PIN Signal USBVCC23 1 2 GND USB_DN_R_3 3 4 GND USB_DP_R_3 5 6 USB_DP_R_2 GND 7 8 USB_DN_R_2 GND 9 10 USBVCC23 ECM-BYT Quick Installation Guide 13 ECM-BYT Quick Installation Guide 2.3.13 On-board header for USB2.0 (H_JUSB12) Signal PIN PIN Signal USBVCC_HSIC34 1 2 GND HSIC_DN_2 3 4 GND HSIC_DP_2 5 6 HSIC_DP_1 GND 7 8 HSIC_DN_1 GND 9 10 USBVCC_HSIC34 2.3.14 Low pin count connector (JLPC1) 14 ECM-BYT Quick Installation Guide Signal PIN PIN Signal LPC_AD0 1 2 +3.3V LPC_AD1 3 4 LPC_PORT80_RST# LPC_AD2 5 6 LPC_FRAME# LPC_AD3 7 8 LPC_PORT80_CLK LPC_SERIRQ 9 10 GND ECM-BYT Quick Installation Guide 2.3.15 Serial port 2 connector (COM2) Signal PIN PIN Signal COM_DCD#_4 1 2 COM_RXD_4 COM_TXD_4 3 4 COM_DTR#_4 GND 5 6 COM_DSR#_4 COM_RTS#_4 7 8 COM_CTS#_4 COM_RI#_4 9 10 NC 2.3.16 Serial port 3 connector (COM3) Signal PIN PIN Signal COM_DCD#_5 1 2 COM_RXD_5 COM_TXD_5 3 4 COM_DTR#_5 GND 5 6 COM_DSR#_5 COM_RTS#_5 7 8 COM_CTS#_5 COM_RI#_5 9 10 NC ECM-BYT Quick Installation Guide 15 ECM-BYT Quick Installation Guide 2.3.17 Serial port 4 connector (COM4) Signal PIN PIN Signal COM_DCD#_6 1 2 COM_RXD_6 COM_TXD_6 3 4 COM_DTR#_6 GND 5 6 COM_DSR#_6 COM_RTS#_6 7 8 COM_CTS#_6 COM_RI#_56 9 10 NC 2.3.18 General purpose I/O connector (JDIO1) Signal 16 ECM-BYT Quick Installation Guide PIN PIN Signal DIO_GP20 1 2 DIO_GP10 DIO_GP21 3 4 DIO_GP11 DIO_GP22 5 6 DIO_GP12 DIO_GP23 7 8 DIO_GP13 SMB_CLK_9555 9 10 SMB_DATA_9555 GND 11 12 +5V ECM-BYT Quick Installation Guide 2.3.19 Miscellaneous setting connector (JFP1) Signal PIN 1 PWBT 2 3 RST# 4 PWR-LED+ 5 PWR-LED- 6 HDD-LED- 7 HDD-LED+ 8 9 COPEN# 10 2.3.20 BIOS SPI connector (BIOS_SPI1) Signal PIN PIN Signal +VSPI_BIOS 1 2 GND SPI_ROM_CS# 3 4 SPI_ROM_CLK SPI_ROM_MISO_R 5 6 SPI_ROM_MOSI SPI_HOLD# 7 8 NC ECM-BYT Quick Installation Guide 17 ECM-BYT Quick Installation Guide 2.3.21 EC Debug connector (JEC_ROM1) Signal PIN EC_SMCLK_DEBUG 1 EC_SMDAT_DEBUG 2 GND 3 2.3.22 LVDS connector (JLVDS1) Signal 18 ECM-BYT Quick Installation Guide PIN PIN Signal +5V 2 1 +3.3V +5V 4 3 +3.3V NC 6 5 NC GND 8 7 GND LVDS_DATA0_P 10 9 LVDS_DATA1_P LVDS_DATA0_N 12 11 LVDS_DATA1_N GND 14 13 GND LVDS_DATA2_P 16 15 LVDS_DATA3_P LVDS_DATA2_N 18 17 LVDS_DATA3_N GND 20 19 GND LVDS_DATA4_P 22 21 LVDS_DATA5_P LVDS_DATA4_N 24 23 LVDS_DATA5_N GND 26 25 GND LVDS_DATA6_P 28 27 LVDS_DATA7_P LVDS_DATA6_N 30 29 LVDS_DATA7_N GND 32 31 GND LVDS_CLK1_P 34 33 LVDS_CLK2_P LVDS_CLK1_N 36 35 LVDS_CLK2_N GND 38 37 GND +12V 40 39 +12V ECM-BYT Quick Installation Guide 2.3.23 Power connector (PWR1) Signal PIN PIN Signal VIN_IN 3 1 GND VIN_IN 4 2 GND 2.3.24 SATA power connector (SATA_PWR1) Signal PIN GND 1 +5V 2 ECM-BYT Quick Installation Guide 19 ECM-BYT Quick Installation Guide 2.3.25 Audio connector (JAUDIO1) Signal PIN PIN FRONT-R-OUT 1 2 FRONT-L-OUT HD_AGND 3 4 HD_AGND LINE1-R-IN 5 6 LINE1-L-IN MIC1-R-IN 7 8 MIC1-L-IN FRONT-JD 9 10 LINE1-JD MIC1-JD 11 12 HD_AGND 2.3.25.1 Signal Description – Audio connector (JAUDIO1) Signal Signal Description LINE1_JD AUDIO IN (LINE_RIN/LIN)sense pin FRONT_JD AUDIO Out(ROUT/LOUT) sense pin MIC1_JD MIC IN (MIC_RIN/LIN) sense pin 20 ECM-BYT Quick Installation Guide Signal
© Copyright 2024 ExpyDoc
