KCU-1P INSTALLATION GUIDE Technical Support: 1-888-442-3269 ext. 264 Fax: 450-442-3230 E-mail: [email protected] Visit us at: www.d-box.com 194-914-0001-EN1 Table of Contents 1. OVERVIEW.............................................................................................................................................................4 2. SOFTWARE INSTALLATION ....................................................................................................................................5 3. HARDWARE INSTALLATION...................................................................................................................................5 4. POWER UP ............................................................................................................................................................6 194-914-0001-EN1 2 of 6 IMPORTANT SAFETY INSTRUCTIONS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Protect the USB cord from being walked on or pinched particularly at the ends. Only use attachments/accessories specified by the manufacturer. Unplug this apparatus during lightning storms or when unused for long periods of time. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user of the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. This symbol indicates that you must communicate with the manufacturer for disposal of the equipment. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. 194-914-0001-EN1 3 of 6 1. OVERVIEW The KCU-1P is a piece of equipment intended to generate KineChain protocol (motion codes), from data provided through a USB port, to an ACM-II or ACM-II 230S actuator drive. The KCU-1P features the following: • • • • USB input through an USB type B jack – at the back of the unit. MASTER OUT output through a RJ-45 jack – at the back of the unit. POWER input, 48 VDC, 0.63 A – at the back of the unit. A LED status indicator – at the front of the unit. The rear plate of the KCU-1P unit is depicted below: 194-914-0001-EN1 4 of 6 2. SOFTWARE INSTALLATION Compatibility; the KCU-1P software is compatible with Windows Vista, Windows 7-8 (32-64 bits) - Access and download the KCU-1P drivers & software at www.d-box.com Run the application and follow the on-screen instructions 3. HARDWARE INSTALLATION WARNING: Do not connect the KCU-1P device into a Windows PC’s USB port until the software has been installed. The driver installation process, which occurs as soon as the device is connected to the PC, requires that the driver file be present on the PC. WARNING: The KCU-1P has been designed to only work with D-BOX ACM-II. Do not connect the KCU-1P to a regular D-BOX ACM. Connect the KCU-1P to the ACM-II accordingly to the diagram below: 194-914-0001-EN1 5 of 6 MASTER OUT Use a shielded CAT.5E patch cord to connect the KCU-1P to a D-BOX ACM-II (Actuator Control Module). • • • • Make sure the CAT.5E patch cord is shielded: the RJ-45 at each end features a metal jacket. Connect one end of the patch cord to the MASTER OUT jack of the KCU-1P. Connect the other end of the patch cord to the Master In Port of the ACM-II. The total length of the patch cord must not exceed 50 feet. USB Use a USB-A / USB-B cable to connect the KCU-1P to the computer (PC). • • • Connect the USB-B end of the cable to the USB plug of the KCU-1P. Connect the USB-A end of the cable to the USB plug of the computer. The total length of the USB cable must not exceed 6 feet. POWER The KCU-1P is provided with its 48 VDC, 0.63 A, 50-60Hz power unit. • • Do not replace the power supply provided but with one from D-BOX. Always connect the main power cord to a grounded plug. 4. POWER UP At power up (48 Volts from the provided power supply is drawn to the unit), the LED located on the front plate indicates the status of the KCU-1P. The boot up sequence is as follows: • • • RED: presence of the 48 V power but no USB connection. ORANGE: Connected to the PC USB port, drivers are installed. The unit is ready to operate GREEN: Active Motion NOTE: When used to drive multiple ACM-II, one KCU-1P can drive the motion signal for a maximum of 20 daisychained ACM-II. This limitation is imposed by the power supply unit. 194-914-0001-EN1 6 of 6
© Copyright 2024 ExpyDoc
