Download Crane Municipal brochure

Municipal
Solutions
Product Overview
brands you trust.
Municipal Pump Applications
Crane Pumps & Systems is the choice for lasting dependability from brands you
trust. We offer quality and durability in water treatment, supply and distribution
as well as treatment and collection. Crane Pumps & Systems also offers a
Pressure Sewer System that is flexible, reliable, cost effective, and overcomes
typical challenges set forth by gravity sewer systems.
Maintenance calls are rare. In fact, some of our pumps have been in service for
more than 30 years.
Our comprehensive selection of municipal products and Pressure Sewer Systems
includes:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
2
Column Sump
Dewatering
EcoTRAN™ System
Effluent
End Suction
Engineered Basin
Grinder
Dry Pit Non-Clog
Replacement Core Unit
Split Case
Submersible Solids Handling
Self-Priming Solids Handling
Sewage Ejector
Submersible Accessories
Sewage & Waste Water
Solutions for private and municipal sewage
transport and waste treatment plant pumping.
page 4
Grinder Pumps & Pressure Sewer
Pumps and systems designed to operate in a
low pressure sewer system where traditional
sewer options are difficult or too costly.
page 10
Clean Water
Water pumps engineered for private and
municipal treatment and distribution systems.
page 14
Dewatering
Pumps manufactured to remove water from
any unwanted area with high efficiency.
page 22
Accessories
Complete line of engineered basins,
level controls, control panels, break away
fittings (BAF’s) and other accessories.
page 24
3
Municipal Products
Sewage & Waste
Water
Barnes Solids Handling Pumps
Model
SH Series
Flow Capacity to
3,250 gpm
Heads to
250’
Discharge Sizes
3”, 4”, 6”, 8”
Max. Solids
3” (4” on 8SH)
Liquid Temperature
104°F Continuous
Features:
•
•
•
•
•
Minimum 3” spherical solids handling
capability on most pumps (2½” on 3SHMP)
Plug-n-Play technology
Temperature and moisture sensors
Slide rail or standalone installation
Large stainless steel lifting bail
Applications:
– Lift stations
– RAS/WAS sludge
– Submersible intake
– Influent/effluent removal
– Treatment plant transfer
– Non-potable water transfer
– Drainage
Construction Details:
•
•
•
•
•
•
•
Enclosed mono vane, dual vane and
3 vane impeller options
Ductile iron impeller construction
(73% stronger than cast iron)
External epoxy coating paint
Readily available type 21 mechanical seals
1.2 service factor on NEMA MG-1 Part
31 Inverter-Duty rated motors
Oil-lubricated bearings rated minimum
50,000 hours at 2 FT/Sec pipe velocity
Optional explosion proof motors
Barnes Solids Handling Pumps
Model
SE Non-Clog Series
Flow Capacity to
900 gpm
Heads to
115’
Discharge Sizes
4”
Max Solids
3”
HP
0.9hp - 15hp
Features:
•
•
•
Unique diaphragm design eliminates
possibility of seal spring clogging
Corrosion resistant
Efficient hydraulic coverage
Construction Details:
•
•
•
•
•
•
4
Cast iron
40-foot cords
(30-foot cords on 56 Frame models)
125 lb. flange design (4” ONLY)
50,000 hour bearing life
Stainless steel lifting bail and hardware
Quick-connect cord on 56 Frame models
Applications:
– Lift stations
Applications:
– Septic tank
– Lift stations
– Waste water pumping
– Decorative water features
– Sump basin water removal
Model
SE Series
Flow Capacity to
430 gpm
Heads to
95’
Discharge Sizes
1.5”, 2”, 3”
HP
0.4hp - 3hp
Max. Solids
2”
Sewage & Waste
Water
Barnes Sewage Ejectors
Features:
•
•
•
•
Single phase motor includes overload
protection
Oil-filled NEMA motors
Oil lubricated upper and lower ball
bearings
Plug-in power cords for simplified
maintenance
Construction Details:
•
•
•
Cast iron construction
Stainless steel pump shaft & hardware
Buna-N O-rings
Crown Self-Priming Pumps
Applications:
– Lift stations
– Sewage treatments
– Digested sludge
Model
PO Series
Flow Capacity to
4,400 gpm
Heads to
165’
Discharge Sizes
2” - 10”
Max Solids
3”
Features:
•
•
Peak efficiencies to 80% require less
horsepower and reduced energy usage
Six discharge sizes
Construction Details:
•
•
•
•
•
•
Cast iron construction
Two vane, ductile iron open impeller
High carbon steel shaft
Corrosion resistant hardware
Single mechanical seal, grease lubricatedbuna/carbon/ceramic
Double seal with oil lubrication on 8” and
10” models
* Various drive and mounting options available.
* Valve accessories available
5
Municipal Products
Sewage & Waste
Water
Deming Dry Pit Non-Clog Pumps
Model
7100 Series
Flow Capacity to
5,000 gpm
Heads to
240’
Discharge Sizes
2” - 8”
HP
250hp
Max. Solids
1.5” - 5”
Features:
•
•
•
•
•
•
•
•
•
Compact design
25 size configurations
External impeller adjustment
Serves a wide range of service conditions
Choice of rotation
Back pull-out design
Positive machine-registered fit design
Hand hole cleanout in casing
Horizontal and vertical configurations
Construction Details:
•
•
•
•
•
•
•
•
•
•
•
•
•
6
All iron construction
Enclosed two-port impeller
Easy axial adjustment
Flanged column construction
Stainless steel pump shaft
Vapor-tight cover plate
Heavy duty ball thrust bearing
Flexible motor coupling
Vertical NEMA C-Flange motors
Float control options
Simplex and duplex units
Re-greasable bearings
Double-row outboard thrust bearing
Applications:
– Pumping sanitary
wastes
– Treatment wastes
– Storm water
– Process wastes
– Pollution control
Applications:
– Solids handling
– Dewatering
Model
800 Series
Flow Capacity to
800 gpm
Heads to
140’
Discharge Sizes
1.5” - 8”
HP
.25hp - 40hp
RPM
1150 - 1750
Max. Solids
2” - 3”
Sewage & Waste
Water
Weinman Column Sump Pumps
Features:
•
•
•
•
•
Compact simplex or duplex design
Adjustable impeller
Vented or vapor tight construction
Extensions for pit depths from 2 to 20 feet
Utilize standard C-face motors
Construction Details:
•
•
•
•
•
•
Renewable shaft sleeve
Conventional enclosed non-clog impeller
with repelling vanes
NEMA type C flange-face motor
Grease lubricated ball thrust bearings
Moveable copper float
Cast iron casing
Barnes Effluent Pumps
Applications:
– Septic tank/
effluent systems
– Flow equalization
– Raw water supply
– Open source
dewatering
– Sump basin water
removal
Model
STEP Series
Flow Capacity to
86 gpm
Heads to
110’
Discharge Sizes
2”
HP
.5hp - 1hp
RPM
3450
Max. Solids*
.75”
Features:
•
•
•
•
Corrosion resistant
Interchangeable with other effluent pumps
Grit resistant
Protective high temperature overload switch
Construction Details:
•
•
•
•
•
Cast iron
Monovane enclosed polypropylene
impeller
Oil-lubricated bearings
Carbon/ceramic/buna seals
Plug-in power cord
* For larger solids see Sewage Ejectors on page 5
7
Municipal Products
Sewage & Waste
Water
Barnes Effluent Pumps
Model
EH & EHV Series
Flow Capacity to
100 gpm
Heads to
85’
Discharge Sizes
2”
HP
.5hp - 1.5hp
RPM
3450
Max. Solids
.75”
Applications:
– Septic tank/ effluent systems
– Flow equalization
– Raw water supply
– Open source dewatering
– Sump basin water removal
Features:
•
•
•
•
Corrosion resistant
Interchangeable with other effluent pumps
Grit resistant
Protective high temperature overload
switch
Construction Details:
•
•
•
•
•
•
Cast iron
Vortex cast iron impeller (EHV Series)
Dual vane semi-open cast iron
Polypropylene impeller (EH Series)
Oil-lubricated bearings
Carbon/ceramic/buna seals
Plug-in power cord (EH Series)
* For larger solids see Sewage Ejectors on page 5
Barnes Effluent Pumps
Model
BP Series
Flow Capacity to
66 gpm
Heads to
30’
Discharge Sizes
2”
HP
.33hp
RPM
1750
Max. Solids
.75”
Features:
•
•
•
•
•
Inboard seal design
Corrosion resistant
Interchangeable with other effluent pumps
Grit resistant
Protective high temperature overload
switch
Construction Details:
•
•
•
•
8
Cast iron, bronze available
Dual vane semi-open thermoplastic
impeller, bronze available
Oil-lubricated bearings
Buna seals
Applications:
– Agriculture
– Sump basin
water removal
Applications:
– Septic tank/
effluent systems
– Flow equalization
– Raw water supply
– Open source
dewatering
– Sump basin water
removal
Model
EP & SP Series
Flow Capacity to
90 gpm
Heads to
33’
Discharge Sizes
1.5”
HP
.33hp - .75hp
RPM
3450
Max. Solids
.50” (SP), .75” (EP)
Sewage & Waste
Water
Barnes Effluent Pumps
Features:
•
•
•
•
•
Corrosion resistant
Interchangeable with other effluent pumps
Grit resistant
Protective high temperature overload
switch
GFCI compatible for safety (SP Series)
Construction Details:
•
•
•
•
•
•
Cast iron
Cast iron vortex impeller
Oil-lubricated bearings
Carbon/ceramic/buna seals
Stainless steel shaft
Permanent split capacitor motor
* Vertical float optional
9
Municipal Products
Barnes Grinder Pumps
Model
OGP
Flow Capacity to
28 gpm
Heads to
200’
Discharge Sizes
1.25”
HP
2hp
RPM
3450
Applications:
– Pressure Sewer Systems
– Small flow lift stations
Features:
Grinder Pumps &
Pressure sewer
•
•
•
•
•
Exclusive quick-connect power cord
Removable discharge flange
Slicerator™ grinding mechanism
Quick and efficient pump change out
Patented two-stage hydraulics for high heads
Construction Details:
•
•
•
•
•
•
Cast iron housings
Vortex bronze impellers
Stainless steel shaft & sleeve
Silicon carbide mechanical seal
Angular contact lower bearings with
100,000 hour bearing life
Oil-filled motor
U.S. Patent 7,357,341
Automatic with
integral check valve
& anti-siphon valve
Manual
Barnes Grinder Pumps
Model
OGV
Flow Capacity to
58 gpm
Heads to
126’
Discharge Sizes
1.25”
HP
2hp
RPM
3450
Features:
•
•
•
•
•
Exclusive quick-connect power cord
Removable discharge flange
Slicerator™ cutter assembly
Reduced life-cycle costs
Available with a horizontal flange discharge
Construction Details:
•
•
•
•
•
10
Cast iron housings
Vortex cast iron impeller
Stainless steel shaft & sleeve
Silicon carbide mechanical seal
Oil-filled motor
Applications:
– Pressure Sewer Systems
– Small flow lift stations
Barnes Grinder Pumps
SGV & XSGV Series
Flow Capacity to
108 gpm
Heads to
160’
Discharge Sizes
1.25” & 2”
HP
2hp, 3hp, 5hp, 7.5hp
RPM
3450
Features:
•
•
•
•
•
•
3-bearing design
Temperature sensors and moisture sensor
options
Exclusive quick-connect power cord
Removable discharge flange (2hp ONLY)
Slicerator™ cutter assembly
Available with a horizontal flange
discharge (2hp ONLY)
Construction Details:
•
•
•
•
•
•
•
Grinder Pumps &
Pressure sewer
Applications:
– Pressure Sewer Systems
– Small flow lift stations
Model
Cast iron housings
Vortex impeller
Stainless steel shaft
Bronze sleeve bearing
Double silicon carbide mechanical seal
available
Oil-filled motor
Class I, Division II, Group D explosion proof
rating (XSGV models)
11
Municipal Products
Barnes Replacement Core Units
Grinder Pumps &
Pressure sewer
12
Model
OGP2022CO
OGP2022AUE
OGVF2022M
Description
1.25” Fixed Discharge Unit
Universal Unit - 1.25” NPT
Flanged Horizontal
1.25” Discharge Unit
Fits
E/One GP200
E/One GP2000
E/One Extreme D-Series
E/One, Hydromatic, Myers
and many others
Replaces ABS S-16 and
S-18 grinder pumps
HP
2
2
2
Volts/Phase
240/1
240/1
240/1
Amps
16.5
16.5
15.0
Flow Capacity
to
28 gpm
28 gpm
58 gpm
Heads to
200’
200’
100’
Applications:
– Pressure Sewer Systems
– Grinder pump stations
Features:
OGP high head grinder pump solves these key
maintenance issues with competitor products:
•
High head outperforms others without
overloading
•
Higher capacity than progressing cavity
provides scouring velocity in pressure lines
•
Centrifugal pump design provides substantially
longer life than progressing cavity technology
•
Available with pre-wired electrical quick
disconnect
Barnes EcoTRAN System
OGV/OGP Series
Flow Capacity to
58 gpm
Heads to
200’
Discharge Sizes
1.25”
HP
2hp
RPM
3450
Features:
•
•
•
•
•
•
Aesthetically pleasing
Simple installation
Day of installation length setting
OGP high head or OGV high flow grinders
ESPS 150 automatic pressure switch
Pre-wired station with DBC – 30’, 50’, 100’
Construction Details:
•
•
•
•
•
•
•
•
•
•
•
Lockable rock-shaped cover
Polypropylene copolymer tank
Fiberglass rebar
Flap-style anti-siphon valve
Stainless steel flexible discharge coupling
Flap-style check valve
Ball-type shut-off valve
Engineered gaskets seal system
Multiple inlet positions
Flood plane watertight covers available
External vent connection available
Grinder Pumps &
Pressure sewer
Applications:
– Pressure Sewer Systems
Model
13
Municipal Products
Deming Split Case Pumps
Model
5060 Series
Flow Capacity to
7,000 gpm
Heads to
800’
Discharge Sizes
2” - 12”
HP
up to 350hp
RPM
870 - 3500
Features:
•
•
•
•
•
•
•
•
•
Dynamically balanced impellers
Guaranteed efficiencies
Horizontal or vertical mounting
Standard packing or mechanical seal
options
Many styles of bases
Extra deep stuffing box with split glands
Grease lube bearings
Sleeves threaded close to impeller to allow
for thermal expansion
Clockwise or counter-clockwise rotation
Construction Details:
•
Clean Water
Pumps
14
•
•
Cast iron, bronze fitted, all iron, lead-free
bronze
Bronze shaft sleeves
Casing & impeller wear rings
Applications:
– Raw water intake
– Water distribution
– Drainage
Weinman Split Case Pumps
1100-1200-1310
Series
Flow Capacity to
6,000 gpm
Heads to
450’ L/LVM Series
800’ JD Series
Discharge Sizes
2” - 12”
HP
up to 400hp
RPM
1150, 1750, 3500
Features:
•
•
•
•
•
•
•
Compact design requires less floor space
Heavy shaft and short bearing span
reduces shaft deflection, longer
mechanical seal and bearing life, and lower
maintenance cost
Upper casing easily removed for inspection
Hydraulically balanced impeller to ensure
longer bearing life and smooth operation
Shaft sleeves tighten with rotation and
allow for thermal expansion
Grease lubricated bearings
Extra deep bearing box
Construction Details:
•
•
•
Cast iron casing
Bronze impeller
Stainless steel or bronze shaft sleeves
Clean Water
Pumps
Applications:
– Water intake distribution
– Drainage
Model
15
Municipal Products
Weinman End Suction Pumps - Threaded Connection
Model
100 & 200 Series
Flow Capacity to
260 gpm
Heads to
200’
Discharge Sizes
2”
HP
up to 15hp
RPM
1150, 1750, 3500
Applications:
– Raw water intake
– Irrigation systems
Features:
•
•
•
•
•
Ni-resist stationary face type seat
mechanical shaft seal (rated to 180°F)
Neoprene defector protects motor or
bearing frame for longer seal life
Cast iron, line bored bearing frame for
perfect bearing alignment
Liquid end top centerline back pull-out
design allows disassembly without
disturbing piping
Tangential design with front cover allows
replacing impeller/wear ring
without disturbing alignment
Construction Details:
Clean Water
Pumps
•
•
•
Stainless steel shaft (56J/6B Frame)
Bronze shaft sleeve (JM/6BA Frame)
Bronze one piece impeller
Weinman End Suction Pumps - Flanged Connection
Model
310 & 500 Series
Flow Capacity to
6,000 gpm
Heads to
450’
Discharge Sizes
2” - 12”
HP
up to 400hp
RPM
1150, 1750, 3500
Features:
•
•
•
•
•
Ni-resist stationary face type seat
mechanical shaft seal (rated to 180°F)
Neoprene defector protects motor or
bearing frame for longer seal life
Cast iron, line bored bearing frame for
perfect bearing alignment
Liquid end top centerline back pull out
design allows disassembly without
disturbing piping.
Tangential design with front cover allows
replacing impeller/wear ring
without disturbing alignment
Construction Details:
16
•
•
•
Stainless steel shaft (56J/6B Frame)
Bronze shaft sleeve (JM/6BA Frame)
Bronze enclosed impeller
Applications:
– Raw water intake
– Irrigation systems
Weinman End Suction Pumps - Back Pull Out
Applications:
– Raw water intake
– Irrigation systems
Model
375 & 575 Series
Flow Capacity to
4,000 gpm
Heads to
500’
Discharge Sizes
up to 8”
HP
up to 125hp
RPM
1760, 1450
Features:
•
•
•
•
•
Extensive range of sizes, efficiencies, and
hydraulics
Back pull out design allows for easy
maintenance
Self-venting tangential discharge
eliminates air entrapment in the pump case
Laser aligned so the unit can be aligned in
the field without bolt bind
Self-flushing mechanical seal, external
piping not required
Construction Details:
Cast iron bronze fitted with slip fit sleeves,
stainless steel sleeves optional
Burks End Suction Pumps - Threaded Connection
Applications:
– Raw water intake
– Chemical injection
Model
GA, G, GN Series
Flow Capacity to
1,100 gpm
Heads to
380’
Discharge Sizes
up to 2.50”
HP
.33hp - 75hp
RPM
1150, 1750, 3500
Clean Water
Pumps
•
Features:
•
•
•
Construction Details:
•
•
•
Casing is close grain iron 30,000psi
minimum tensile strength
Cast iron case – bronze fitted or all iron or
all bronze
Bronze enclosed impeller
•
•
Impeller is balanced for vibration free
operation and threaded onto stainless steel
motor shaft
NPT threaded & flanged suction &
discharge connections - Discharge can be
located in any four positions
Back pull out design eliminates the need to
disturb piping should the pump
ever require service – the casing
stays in the line
Standard self-adjusting shaft seal for
temperatures to 255°F
Standard single Type 21 mechanical seal
carbon/ceramic/Buna-N® rated to 225°F for
long trouble-free service - Special seals are
available for higher temperatures
and fluids other than water
17
Municipal Products
Weinman In-Line Centrifugal Pumps
Model
320 Series
Flow Capacity to
1,400 gpm
Heads to
360’
Discharge Sizes
1.5” - 6”
HP
up to 60hp
RPM
1750, 3500
Features:
•
•
•
•
•
Automatic purge system allows liquid
to flow from high pressure side of impeller
across seal face to low pressure
eye of impeller, assuring proper lubrication
and venting. Model 6012CV
utilizes external venting
Manual vent plug ensures positive
lubrication at start up
Mechanical seals eliminate packing
Motor can be rotated at 90° intervals for
convenient junction box location
Drain plug controls water drainage for easy
service
Construction Details:
Clean Water
Pumps
18
•
•
•
•
NEMA JM frame motors are standard on
models greater than 1 hp
ANSI flanges standard 125lb
(250lb available)
Shaft sleeve on JM frame motors
Bronze enclosed impeller
Applications:
– Water circulation
– Booster service
Burks Vertical Multi-Stage Pumps
BPV Series
Flow Capacity to
396 gpm
Heads to
820’ - 1350’
Discharge Sizes
1.25” - 4”
HP
.5hp - 60hp
RPM
1750, 3500
Features:
•
•
•
•
Special diffuser design reduces internal
losses, which improves pump efficiency
Sleeve construction ensures total
compensation of thermal expansion
Bleed plug is engineered to ensure safe
purging of air
The BPVCF configuration is dimensionally
interchangeable with the BPVF series
Construction Details:
•
•
•
•
Mechanical seal options; fixed, easy access,
or cartridge
Stainless steel pump shaft
Stainless steel housing
Stainless steel diffuser
Clean Water
Pumps
Applications:
– Boiler feed water
– High pressure transfer
– Pressure booster systems in
buildings and potable water
– Potable water
– Sprinklers and irrigation
– Jockey pumps for fire
suppression systems
– Batch processing
– Batch transfer
– Continuous transfer
Model
19
Municipal Products
Burks Self-Priming Pumps
Model
W Series
WA6 Series
Flow Capacity to
270 gpm
90 gpm
Heads to
178’
130’
Discharge Sizes
1”, 1.50”, 2”
1”, 1.50”
HP
.33hp - 10hp
1hp - 3hp
RPM
3500
3500
Features:
•
•
•
Applications:
– WA/WT Series for water
and other 1.0 S.G. fluids
– WST Series for petroleum
solvents and other 0.82 S.G.
fluids
Compact, close coupled design
Fitted with standard carbon, ceramic
mechanical seals
WST pumps provided with
explosion-proof motors
Construction Details:
•
Cast iron construction (except WA6
which standard is bronze fitted, but
all cast iron is optional)
Clean Water
Pumps
Crown Self-Priming Pumps
Model
CU Series
Flow Capacity to
400 gpm
Heads to
184’
Discharge Sizes
1.5” - 3”
HP
Base Mounted up to 150hp
Close-coupled .33hp - 15hp
RPM
3500
Features:
•
•
•
•
•
•
PDA (Product Data Assessed) by ABS
(American Bureau of Shipping)
Fast priming
Self-priming to 20 feet
Back pull out on some models
Heavy duty shafts for durability
Available in frame-mounted and
closed-coupled
Construction Details:
•
•
•
20
Cast iron construction
Cast iron open impeller
Stainless steel shaft
Applications:
– Raw water
– Clear water
– Liquid transfer
booster pumps
Barnes Submersible Fountain Pumps
SF SFU, 3SF Series
Flow Capacity to
325 gpm
Heads to
55’
Discharge Sizes
SFU - 1.75” Hose
SF - 2” & 3” NPT
HP
.33hp - 3hp
RPM
1750, 3500
Features:
•
•
Thermal overload protection in motor
Oil-filled motor
Construction Details:
•
•
•
•
Stainless steel screen (SFU Series)
Stainless steel shaft
Brass or cast iron open impeller
Cast iron construction (SF Series)
Clean Water
Pumps
Applications:
– Decorative water
displays
Model
21
Municipal Products
Prosser Dewatering Pumps
Model
Standard-Line
Flow Capacity to
1,460 gpm
Heads to
248’
Discharge Sizes
2” - 6”
HP
.75hp - 50hp
RPM
3500
Applications:
– Decorative water displays
– Manhole dewatering
– Construction dewatering
Features:
•
•
•
•
•
•
Pumps require no priming, suction hose,
or foot valve
Operate in any position
Bearings require no outside lubrication
Unique in-line design ensures a coolrunning motor by transferring motor heat
directly to the pumped fluid
Abrasion resistant impellers and silicon
carbide outboard shaft seals help ensure
trouble-free performance
130 different models
Construction Details:
•
•
•
Aluminum casing
Stainless steel pump shaft
Stainless steel or polyurethane impeller
Prosser Submersible Pumps
Dewatering
Pumps
Model
Hymergible Series
Flow Capacity to
359 gpm
Heads to
348’
Discharge Sizes
1.5” - 4”
HP
up to 50hp
RPM
varies depending on
hydraulic pressure
Features:
•
•
•
•
•
•
Slim-line design allows pumps to
fit where other pumps can’t
Lightweight for easy portability
Require no priming, suction hose or foot valve
Operate in any position
Able to run dry for a reasonable
period of time without damage
Hydraulically driven with pressures of
350 - 2000 psi and power input of
7 - 12 GPM
Construction Details:
22
•
•
•
•
Aluminum casing
Stainless steel impeller
Stainless steel shaft
Hydraulic driven
Applications:
– Mining and
other applications
with explosive
environments
Barnes Submersible Pumps
Applications:
– Construction dewatering
– Emergency flood dewatering
– Telecom vault dewatering
Model
SED Series
Flow Capacity to
1,860 gpm
Heads to
127’
Discharge Sizes
2” - 6”
HP
.50hp - 40hp
RPM
1750
Features:
•
•
Compact design
No priming, suction hose or foot valves
are required
Construction Details:
•
•
•
Cast iron housing
Cast iron open impeller
Ductile iron strainer
Applications:
– Excavation
– Construction
– Landscaping
– Agriculture
– Industrial
– Commercial
– Residential
– Decorative water
features
– Dewatering
emergencies
Model
70, 71, 125, 126
Series
Flow Capacity to
100 gpm
Heads to
50’
Discharge Sizes
2”
HP
.75hp - 1.25hp
RPM
3450
Features:
•
•
•
•
•
•
•
•
•
Stainless steel motor housing
Polyurethane wear resistant semi-open
impellers and diffusers
Rubberized strainers for durability
25’ polypropylene lifting rope provided
with pump
•
Dewatering
Pumps
Barnes Submersible Pumps
Compact design
Portability – Model 70 weighs 30lb and
model 125 weighs 35lb with ergonomically
designed lifting handle
Job site flexibility – Each model includes a
50’ power cord to reach remote locations
No control box – Start and run capacitors
are in the pump motor shell
Low current requirements allows an
existing generator to be used
Pumps can run dry for extended periods
without damage
Construction Details:
•
•
Motors are standard with Class F insulation
Tandem oil lubricated silicon carbide
mechanical seals are standard
23
Municipal Products
Accessories
Basins
• Custom molded fiberglass reinforced polyester resin
• Wall thickness sufficient to withstand a water-saturated
sand load of 120 lbs per cubic foot with a 1.5 safety factor
• Ballast support flange extends three inches on the radius
of the basin
• Basin will withstand a maximum temperature of 150˚F
• Factory pre-wiring available
• Simplex or duplex configuration
4' to 20'
in length
C-Channel Rail Options:
• Stainless steel discharge piping
• For use with 1.25” and 2”
NPT discharge grinder, solids
handling, and effluent pumps
• 24” - 72” basin diameters
• 48” - 240” basin lengths
Flex Hose Options:
• EPDM Hose and PVC Piping
• For use with 1.25” NPT
discharge grinder
• 24” basin diameter
• 48” - 96” basin lengths
Covers
24" to 72"
in diameter
C-Channel rail system
Free-standing pump
and level control
Accessories
UltraCAP2
• Rugged, polyethylene removable self-venting
drywell and cover are engineered to fit the 24"
and 30” reduced opening diameter basins used
on pre-wired package systems.
Molded Polyethylene
• Rugged, light weight rotomolded polyethylene
grass green cover that is self-vented and
engineered to fit all standard 24" and 30” reduced
diameter basins.
Fiberglass
• Reinforced plastic and are grass green in color.
Covers for 24" and 30" diameters are 3/8" thick,
36" and 42" diameters are 1/2" thick.
Steel
• Steel cover has a black powder coating. Covers
available for basin diameters 36" through 60" and
are 3/8" thick.
Aluminum
• Available for basin diameters 36" and 42” are 1/4"
thick. 48” and 60” are 3/8” thick.
Molded Polyethylene
Steel
Aluminum
24
Accessories
Level Controls
Float Tree
• Slim, rigid column with NO
• Simple design
moving parts. Unit is unaffected
• Field adjustable operating points
by solids, grease buildup, or liquid
• Easily mounts into basin guide rail swirling in basin.
with a heavy duty slide bracket
• Mounts easily in Engineered
Basins with a rail system using a
ESPS Design Features
heavy duty slide bracket.
• Pressure switch parts are
•
NO
field adjustment required
protected from the basin
because
operating levels are
environment with a Barnes
factory
preset.
exclusive sealed design.
This product may be covered by one or
more of the following patents and other
patent(s) pending: US Patent 7,578,657
Break Away Fittings (BAF)
Barnes break away fittings allow pump installation and removal
without wet well entry or piping disconnection. Break away fittings
provide easy access to all Barnes 1 1/4” (32mm) thru 8” (200mm)
submersible pumps; units may be adapted for other submersibles
with similar discharge sizes. Available in non-sparking design.
Control Panels • Indoor/Outdoor High Water Alarms
A variety of remote alarms with warning lights
and/or annunciators for indoor or outdoor use
may be specified. Require 120v power supply.
The pump monitor relay provides motor over
temperature alarm and seal leakage alarm for
submersible pumps.
Accessories
Barnes control panels provide proven, reliable
performance and potential malfunction
warning. Simplex and duplex models are
contained within a NEMA 4X enclosure and are
available with single or three phase power. All
components are UL listed.
25
Municipal Products
Accessories
1. Flexible Inlet Pipe Fittings
The flexible pipe fitting is super tough for weather and corrosion
resistance. The fitting has superior vapor and water leakproof
sealing ability. Available 1¼" thru 6".
7
2. Flexible Discharge
Braided stainless steel flexible discharge protects against
damage from soil settling. 1.25” - 2.50” NPT.
5
3
3. Inlet Hubs
Cast iron inlet hubs are recommended for cast iron, ceramic,
plastic or ductile iron gravity sewer pipe, and are designed to fit
curvature of basin. 4”, 6” and 8”.
1
6
4. Electrical Conduit Hubs
Bolt-on hub, constructed of glass filled nylon. 1.25”, 1.50”, 2” NPT.
5. Discharge Couplings
Stainless steel bolt-on couplings available in 1¼", 1½", 2", and 2½"
NPT sizes.
6. Bulkhead Fitting
Safety lock design permits safe, quick pipe connection. Fitting
comes standard with heavy duty buttress threads to help
prevent leaks under pressure. 1.25” NPT.
10
4
7. “C” Channel Guide Rails
Rail mounts to the upper and lower horizontal brackets, attached
to the basin wall. The rail rests on the bottom of the basin floor,
supporting the pump and the required distance from the basin
floor. Guide brackets are attached to the pump for positioning of
the unit on the guide rail during installation and removal.1.25”
and 2” NPT.
2
8. True Union Ball Valves
Manufactured of Sch. 80 PVC type I with EPDM o-rings for
superior chemical and corrosion resistance. 1.25” & 2.00” NPT ball
valves are of quick disconnect design with full port bore, ¼ turn
leak tight shut-off and NSF listed for use in water service.
8
9. Ball Check Valve
1.25”, 1.50” and 2.00” NPT are available in cast iron or PVC. Works
both vertically and horizontal. Ball has sufficient weight to seat
tightly and moves freely to open. Head loss is low as the ball is
set completely to one side at the maximum rate of flow.
Accessories
26
10. Swing Check Valve
Made of high impact Sch. 40 PVC type II material, suitable in
systems where fluid is corrosive or contains debris, industrial
waste disposal, sewage, etc. The EPDM swing gate lifts to provide
unobstructed flow. 1.25” through 2.00” NPT.
9
18
Accessories
11. Swing Check Valve with Integrated Anti-Siphon
Available in 1.25” and 2.00” NPT C-Channel and 1.25” NPT In-Line
configurations. Cast iron construction with powder coat finish.
14
12. Remote Alarm Wall Plate
Allows the homeowner to install a fault warning light indoors.
Available in various color options and installs in a standard single
gang style enclosure.
13. Adapter Kits
Prosser adapter kits allow for operation where the discharge of
one pump is directly connected to the suction of another. The
same small diameter casing can be utilized while effectively
doubling the head at a given flow. *Photo not shown
12
14. Lifting Hoist
Designed to be moved from pump station to pump station, to
raise and lower submersible grinder or effluent pumps.
15. Mushroom strainers
Prosser mushroom strainers pump water levels down to within
1/4” of level floor. (available with .75hp and 1.0hp pumps)
16. Sludge strainers
Prosser strainers are constructed of 300 series stainless steel.
Strainer kits include, strainer, and mounting hardware.
15
17. Nema 4 watertight control & dual level control
The combination pump and dual float level control is in a Prosser
NEMA 4 watertight enclosure with manual on-off switch, circuit
breaker with short circuit and overload protection, magnetic
contactor, transformer to reduce line voltage to 24 volt, two level
sensing float switches with cable and float override switch for
manual operation.
11
18. Level controls, wide angle, pipe mounted
Level controls are available in pipe mounted configuration with a
115 volt molded on male and female piggy-back plug w/ ground.
Cable lengths are of 15 (5M), 25 (8M), 30 (9M) and 50 feet (15M).
The unit has a piggy-back plug attached to the cord, allowing
the user to plug the pump plug directly into it, and then plug the
entire unit into a 115 volt or 230 volt grounded outlet.
Accessories
17
11
16
27
A Crane Co. Company
Crane Pumps & Systems
420 Third Street
Piqua, Ohio 45356
(937) 778-8947
Fax (937) 773-7157
www.cranepumps.com
Crane Pumps & Systems Canada
83 West Drive
Brampton, Ont. Canada L6T 2J6
(905) 457-6223
Fax (905) 457-2650
brands you trust.
 2013 Crane Pumps & Systems, Inc.
A Crane Co. Company
Printed in U.S.A.
MUNIFULLBRO - Rev. A (5/13)

Download Report