PLT6008 Rev C.PDF - Monogram Aerospace Fasteners

MONOGRAM
AEROSPACE
FASTENERS
R
a TriMas company
L
BREAK-OFF LIMITS
(MEASURED FROM SKIN
SURFACE) (SEE TABLE I)
G
.332
MANUFACTURER'S IDENTIFICATION
MONOGRAM = N
3
ALCOA = VS
H
A
9
D
B
.035"
[0,89
C
MAX
.010" X 45
0,25 mm]
J MAX
F
WRENCH
FLATS
90°
R. R
.5
SLEEVE
8
FASTENER IDENTIFICATION 3
SCREW
NUT
LOCKING FEATURE 4
K
MAX
5
GRIP
DRIVE NUT WRENCH FLATS
-8 = 3/8" [9.52 mm] HEX
TYPICAL INSTALLATION
TABLE I
PART
NUMBER
PLT6008-8-( )
NOM
INCH
.2590
A
C
MAX
B
mm
INCH
mm
INCH
mm
6,579
.416
.396
10,57
10,06
.380
.340
9,65
8,64
INCH
.354
D
mm
INCH
mm
8,99
.2600
.2580
6,604
6,553
F
WRENCH
FLATS
INCH mm
INCH
mm
.135
.130
.063
.053
1,60
1,35
3,43
3,30
J
MAX
H
INCH
K
MAX
mm
.384
INCH
9,75
.325
R. R
mm
INCH
mm
8,26
.025
.015
0,64
0,38
7
BREAK-OFF
LIMITS
PART
NUMBER
PLT6008-8-( )
INCH
mm
+.053
-.035
+1,35
-0,89
TABLE I (CONTINUED)
PREVAILING
MINIMUM
HOLE SIZE
TORQUE
AVAILABLE
MIN
GRIP LENGTH
(TABLE II)
INCH mm IN-LBS Nm
-3
.264
.261
6,71
6,63
2.5
0,282
DOUBLE SHEAR
STRENGTH
MIN
LBS
N
9000
40030
TENSILE
STRENGTH
MIN
LBS
N
2100
9340
EXAMPLE PART NUMBER:
PLT6008 ( ) -
8 -
5
GRIP LENGTHS IN 1/16THS (SEE TABLE II)
NOMINAL BODY DIAMETER IN 1/32" (SEE TABLE I)
DESIGNATES SPECIAL FINISH CODE (SEE PLT5003) 6
BASIC PART NUMBER, SELF-LOCKING BLIND FASTENER
R
MONOGRAM
AEROSPACE
FASTENERS
a TriMas company
3423 SOUTH GARFIELD AVENUE
COMMERCE, CALIFORNIA 90040
(323) 722-4760 FAX (323) 727-1029
TITLE:
DRAWING NO:
VISU-LOK® II, FASTENER, BLIND,
DOMED HEAD, SELF-LOCKING WITH DRIVE NUT,
ALLOY STEEL
PROPRIETARY AND CONFIDENTIAL:
NOTICE: THIS DRAWING IS PART OF THE PROPRIETARY ARTICLE HEREIN DISCLOSED, OWNED BY MONOGRAM AEROSPACE FASTENERS, ANY PARTY BY ACCEPTING THIS DOCUMENT
ASSUME CUSTODY THEREOF AND AGREES:
A: THE INFORMATION SET FORTH HEREIN IS GIVEN IN CONFIDENCE AND THIS DOCUMENT WILL NOT BE COPIED OR REPRODUCED IN WHOLE OR IN PART, NOR ITS CONTENTS
REVEALED IN ANY MANNER TO ANY PERSON EXCEPT TO MEET THE PURPOSE FOR WHICH IT WAS DELIVERED.
B: WITHOUT THE WRITTEN CONSENT OF MONOGRAM AEROSPACE FASTENERS, THIS DOCUMENT AND THE INFORMATION CONTAINED HEREIN UNDER NO CIRCUMSTANCES WILL
BE USED IN THE MANUFACTURE OR REPRODUCTION OF THE ARTICLE DISCLOSED, AND THE DELIVERY OF THIS DOCUMENT SHALL NOT CONSTITUTE ANY RIGHT OR LICENSE TO DO SO.
PLT6008( )-( )-( )
DRAWN BY:
A PEREZ
APPROVED BY:
Alcoa
MONOGRAM
5M902
98524
CAGE CODE:
CAGE CODE:
DRAWN DATE:
04/05/2014
CHECKED DATE:
ECN NO:
14-0286
ECN DATE:
REV:
C
04/05/2014 SHEET 1 OF 2
R
MONOGRAM
AEROSPACE
FASTENERS
a TriMas company
2ND
DASH
NO.
-3
-4
-5
-6
-7
G
+.040/-.010
[+1,02/-0,25 mm]
INCH
mm
.202
.244
.285
.320
.447
5,13
6,20
7,24
8,13
11,35
TABLE II
GRIP RANGE
INCH
MIN
.162
.203
.245
.280
.407
mm
4,11
5,16
6,22
7,11
10,34
(L)
MAX
INCH
mm
INCH
.202
.244
.285
.320
.447
1.848
1.890
1.931
1.966
2.093
5,13
6,20
7,24
8,13
11,35
-8
mm
46,94
48,01
49,05
49,94
53,16
APPLICABLE SPECIFICATIONS:
PROCUREMENT SPECIFICATION: NAS1675, CLASS I, EXCEPT HEAD STYLE, GRIP RANGE AND BREAK-OFF LIMITS.
MATERIAL:
NUT AND SCREW:
SLEEVE:
DRIVE NUT:
ALLOY STEEL 4130 PER AMS-S-6758, ALLOY STEEL 4140 PER AMS6382 OR AMS6349 OR ALLOY STEEL 8740 PER AMS6322.
CRES 303 OR CRES 304 PER AMS-QQ-S-763, AMS5639 OR AMS5641.
MILD STEEL.
HEAT TREAT:
NUT AND SCREW:
SLEEVE:
DRIVE NUT:
HEAT TREAT PER NAS1675.
AS REQUIRED FOR PERFORMANCE.
AS REQUIRED FOR PERFORMANCE.
6
FINISH:
NUT AND SCREW:
SLEEVE:
DRIVE NUT:
CADMIUM PLATED PER AMS-QQ-P-416 TYPE II, CLASS 2 OR PER NAS672 (EXCEPT THERMAL INDICATOR MAY BE OMITTED).
PASSIVATE PER AMS2700. CADMIUM PLATED PER AMS-QQ-P-416, TYPE I, CLASS 3.
BLACK OXIDE.
6
LUBRICATION:
NUT:
SCREW AND SLEEVE:
WWM CARBO-WAX, PARAFFIN WAX, LAURIC ACID AND/OR CETYL ALCOHOL.
SOLID DRY FILM LUBRICANT, WWM CARBO-WAX, PARAFFIN WAX, LAURIC ACID AND/OR CETYL ALCOHOL.
LUBRICANTS LISTED MAY BE APPLIED TO ANY OR ALL COMPONENTS AS REQUIRED FOR PERFORMANCE.
GENERAL NOTES:
1.
OUTSIDE DIAMETER OF HEAD OF SCREW AND OUTSIDE DIAMETER OF SLEEVE SHALL NOT BE GREATER THAN MAXIMUM "
D".
2. REMOVE ALL LOOSE OR HANGING BURRS.
3. HEAD MARKINGS ON NUT DEPRESSED .010 INCH [0,254 mm] MAXIMUM. POSITION OPTIONAL.
4. LOCKING FEATURE CONSISTS OF THREE (3) INDENTATIONS LOCATED 120 APART ON THE PERIPHERY OF THE NUT COMPONENT
AND APPROXIMATELY .040" [1,02 mm] ABOVE THE INTERSECTION OF THE NUT NOSE ANGLE AND O.D. (MEAN GRIP OF FASTENER).
5. DISTORTION OF "
D" PERMISSIBLE IN LOCKING AREA.
6. STANDARD FINISHES AND LUBRICANTS ARE SHOWN ABOVE. REFER TO SPECIFICATION PLT5003 FOR SPECIAL FINISHES AND/OR
LUBRICANTS, IF REQUIRED.
7. MUST ENTER A .2610" [6,63 mm] HOLE WITH FINGER PRESSURE.
8. ALTERNATE PART IDENTIFICATION: "1077".
9. PLATING IS OPTIONAL ON PINTAIL.
R
MONOGRAM
AEROSPACE
FASTENERS
a TriMas company
3423 SOUTH GARFIELD AVENUE
COMMERCE, CALIFORNIA 90040
(323) 722-4760 FAX (323) 727-1029
TITLE:
DRAWING NO:
VISU-LOK® II, FASTENER, BLIND,
DOMED HEAD, SELF-LOCKING WITH DRIVE NUT,
ALLOY STEEL
PROPRIETARY AND CONFIDENTIAL:
NOTICE: THIS DRAWING IS PART OF THE PROPRIETARY ARTICLE HEREIN DISCLOSED, OWNED BY MONOGRAM AEROSPACE FASTENERS, ANY PARTY BY ACCEPTING THIS DOCUMENT
ASSUME CUSTODY THEREOF AND AGREES:
A: THE INFORMATION SET FORTH HEREIN IS GIVEN IN CONFIDENCE AND THIS DOCUMENT WILL NOT BE COPIED OR REPRODUCED IN WHOLE OR IN PART, NOR ITS CONTENTS
REVEALED IN ANY MANNER TO ANY PERSON EXCEPT TO MEET THE PURPOSE FOR WHICH IT WAS DELIVERED.
B: WITHOUT THE WRITTEN CONSENT OF MONOGRAM AEROSPACE FASTENERS, THIS DOCUMENT AND THE INFORMATION CONTAINED HEREIN UNDER NO CIRCUMSTANCES WILL
BE USED IN THE MANUFACTURE OR REPRODUCTION OF THE ARTICLE DISCLOSED, AND THE DELIVERY OF THIS DOCUMENT SHALL NOT CONSTITUTE ANY RIGHT OR LICENSE TO DO SO.
PLT6008( )-( )-( )
DRAWN BY:
A PEREZ
APPROVED BY:
Alcoa
MONOGRAM
5M902
98524
CAGE CODE:
CAGE CODE:
DRAWN DATE:
04/05/2014
CHECKED DATE:
ECN NO:
14-0286
ECN DATE:
REV:
C
04/05/2014 SHEET 2 OF 2

Download Report